Resumo do conteúdo contido na página número 1
ENG
Prestigio P400MW / P460MW
Colour Television
Owner’s Manual
Please read this manual carefully before operating your set. Retain it for future reference.
See the label attached on the back cover and quote this information to your dealer when you require service.
PRESTIGIO P400MW / P460MW 1
Resumo do conteúdo contido na página número 2
Contents Installation ........................................................ 3 Sound adjustment ........................................... 22 SSM (Sound Status Memory) ............................... 22 Remote control handset ..................................... 4 Balance ............................................................... 23 Controls ................................................................ 4 AVL (Auto Volume Leveler) .................................. 23 Battery installa
Resumo do conteúdo contido na página número 3
ENG Installation Power This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or power-cuts, please pull out the aerial and mains plugs. Warning To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently. Service Never remove the back cover o
Resumo do conteúdo contido na página número 4
Remote control handset Controls Before you use the remote control handset, please install the batteries. -All the functions can be controlled with the remote control handset. -Some functions can also be adjusted with the buttons on the front panel of the set. POWER MUTE switches the set On from standby or switches the sound On or Off. Off to standby. SSM (Sound Status Memory) NUMBER BUTTONS recalls your preferred sound setting. PSM (Picture Status Memory) ARC recalls your preferred picture setti
Resumo do conteúdo contido na página número 5
ENG Battery installation -Your remote control handset is powered by two AAA type batteries. 1 To insert batteries, turn the remote control handset over and remove the battery cover. 2 Put the two batteries into the compartment observing battery polarity. 3 Replace the cover. To avoid damage from possible bat-tery leakage, remove the batteries if you do not plan to use the remote con-trol handset for an extended period time. Do not use batteries of differing age or type. Always discard of batter-
Resumo do conteúdo contido na página número 6
Controls of Front panel -Shown is a simplified representation of the set. -Here shown may be somewhat different from your set. -This manual explains the features available on the P400MW / P460MW series. 1. MAIN POWER 5. INPUT SELECT switches the set On or Off. selects TV , AV1, AV2, AV3, AV4, S-VIDEO, COMPONENT1, COM- PONENT2, PC-RGB, HDMI1, HDMI2 mode. 2. /\ / \/ (Programme Up/Down) selects a programme or a menu item. 6. POWER switches the set On from standby. switches the set On from standby o
Resumo do conteúdo contido na página número 7
ENG Connections of Back panel 8 9 AUDIO AUDIO R R L Y Y Pb b Pr r ANT. IN RGB INPUT HDMI1 INPUT HDMI2 INPUT AUDIO INPUT RS-232C INPUT AUDIO INPUT AV1 AV2 AV3 OPTICAL AC INPUT (480i/480p/720p/1080i/1080p) (CONTROL/SERVICE) COMPONENT1 INPUT 2 3 4 5 6 7 1 1. HDMI1INPUT / HDMI2 INPUT / AUDIO INPUT 6. Digital Audio (OPTICAL) / RGB INPUT SOCKETS Connect digital audio from various types of equipment. Connect the set output socket of the PERSONAL COMPUTER to this socket. Note : In standby m
Resumo do conteúdo contido na página número 8
Connection to External equipment -You can connect additional equipment, such as VCRs, camcorders etc. to your set. However please check with your manufacturers instruction books for specific information. Make sure all connections are made with both your set and additional appliance unplugged from the mains to avoid damaging your equipment. Here shown may be somewhat different from your set. 1 Connect to Aerial socket Connect the RF out socket of the VCR to the aerial socket on the back of the se
Resumo do conteúdo contido na página número 9
ENG 3 Watching Cable TV - After subscribing for a local cable TV station and installing a converter you can watch cable TV. - For further information of cable TV, contact the local cable TV station. In using connection 1 Select programme number in programme switch of cable box. Match the set programme with selected programme of cable box. Select your desired programme with the remote control for cable box. In using connection 2 Use the INPUT SELECT button on the remote control and select AV1, AV
Resumo do conteúdo contido na página número 10
5 Watching DVD How to connect Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD INPUT) and audio inputs to Audio sockets of AUDIO INPUT. How to use Turn on the DVD player, and insert a DVD. Use INPUT SELECT button on the remote con- trol to select COMPONENT1, COMPONENT2. Refer to the DVD play-er’s manual for operat- ing instructions. � COMPONENT Input ports You can get better picture quality if you con- nect DVD player with COMPONENT input ports as below. 6 Connecting HDMI (DTV) Connect th
Resumo do conteúdo contido na página número 11
ENG 7 Connecting PC (DTV) Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the RGB INPUT sock-et of the set. Connect the audio cable from the PC to the AUDIO INPUT sockets of the set. Press the INPUT SELECT button to select PC- RGB. Switch on the PC, and the PC screen ap- pears on the set. The set can be operated as the PC monitor. RGB-DTV input signal : 480p-60Hz, 576p- 50Hz, 720p-50Hz, 720p-60Hz, 1080i-50Hz, 1080i-60Hz, 1080p-50Hz, 1080p-60Hz. 8 Connecting Di
Resumo do conteúdo contido na página número 12
Basic operation 1 On and Off Press the main power button to switch the set on. If the set is in standby mode, press the POWER, /\ / \/ buttons on the remote control handset to switch it on fully. Press the POWER button on the remote control handset. The set reverts to standby mode. Press the main power button again to switch the set off. 2 Programme selection You can select a programme number with the /\ / \/ or NUMBER buttons. 3 Volume adjustment Press the < / > button to adjust the volume. If
Resumo do conteúdo contido na página número 13
ENG On screen menus Menu selection -The dialogue between you and your set takes place on screen with an operator menu. The buttons required for the operating steps are also displayed. 1 3 Press the MENU button and then use /\ / \/ button to dis- Press the > button to display the sub menu or the pull- play each menu. down menu. 2 4 Press the > button and then use /\ / \/ button to select a Change the setting of an item in the sub or pull-down menu item. menu with < / > or /\ / \/. You can move to
Resumo do conteúdo contido na página número 14
Setting up TV stations Auto programme tuning -Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the /\ / \/ or NUMBER buttons to scan the stations you programmed. Stations can be tuned using automatic or manual modes. -All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set. 1 Press the MENU button and then use /\ / \/ button to select th
Resumo do conteúdo contido na página número 15
ENG To stop auto programming, press the MENU button. When auto programming is completed, the Edit menu appears on the screen. See the ‘Programme edit’ section to edit the stored pro-gramme. Repeatedly press the MENU button to return to normal TV viewing. Manual programme tuning -Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name with five characters to each programme number. 1 Press the MENU button and then use D / E
Resumo do conteúdo contido na página número 16
4 Normally fine tuning is only necessary if reception is poor. Press the /\ / \/ button to select Fine. Press the < / > button to fine tune for the best picture and sound. Press the /\ / \/ button to select Search. Press the < / > button to commence searching on the Search pull-down menu. If a station is found the search will stop. If this station is the one required, press the OK button to store it. 5 Press the /\ / \/ button to select Name. Press the > button on the Name pull-down menu. Press
Resumo do conteúdo contido na página número 17
ENG Programme edit -This function enables you to delete or skip the stored programmes. Also you can move some stations to other pro-gramme numbers or insert a blank station data into the selected programme number. 1 Press the MENU button and then use /\ / \/ but-ton to select the STA-TION menu. Press the > button and then use /\ / \/ button to select Edit. Press the > button to display the Edit menu. 2 Deleting a programme Select a programme to be deleted with the /\ / \/ or < / > button. Press
Resumo do conteúdo contido na página número 18
Calling the programme table -You can check the programmes stored in the memory by displaying the programme table. 1 Displaying programme table Press the LIST button to display the Programme table menu.The programme table appears on the screen. One programme table con-tains ten programmes as below. You may find some blue programmes. They have been set up to beskipped by auto programming or in the programme edit mode.Some programmes with the channel number shown in the programmetable indicate ther
Resumo do conteúdo contido na página número 19
ENG Picture adjustment CSM (Colour Status Memory) To initialize values (reset to default settings), select the Normal option. Press the MENU button and then /\ / \/ button to select the PICTURE menu. Press the > button and then /\ / \/ button to select CSM. Press the > button and then /\ / \/ button to select the desired colour temperature. Repeatedly press the MENU button to return to normal TV viewing. You can adjust red, green, or blue to any colour tempera-ture you prefer. Press the MENU but
Resumo do conteúdo contido na página número 20
2 PSM (Picture Status Memory) Press the MENU button and then use /\ / \/ button to select the PICTURE menu. Press the > button and then use /\ / \/ button to select PSM. Press the > button and then use /\ / \/ button to select a picture setting on the PSM pull-down menu. Repeatedly press the MENU button to return to normal TV viewing. You can also recall a desired picture (Dynamic, Standard, Mild, Game or User) with PSM button on the remote con- trol. The picture Dynamic, Standard, Mild, Game ar
