Resumo do conteúdo contido na página número 1
User’s manual
TL7000
Handset lifter
for use with AT&T models
TL7610/TL7650
Resumo do conteúdo contido na página número 2
Congratulations on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety information on page 22 of this manual. Please thoroughly read the user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. You can also visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Model #: TL7000 Type: Handset lifter Serial #:
Resumo do conteúdo contido na página número 3
Parts checklist Check to make sure the handset lifter package includes the following items: User's manual Handset lifter Ring detector Telephone line cord (4 conductor) with a color label in orange Large lifter pad Anti-slip pad Color label (light blue)
Resumo do conteúdo contido na página número 4
User’s manual TL7000 Handset lifter for use with AT&T models TL7610/TL7650 Table of contents Getting started Quick reference guide Handset lifter ................................................................................................1 Handset lifter installation Lifter installation .......................................................................................3 Installation of large lifter pad (optional) ........................................5 Installation o
Resumo do conteúdo contido na página número 5
Troubleshooting Troubleshooting ............................................................................................17 Maintenance and safety Maintenance ...................................................................................................21 Important safety information .................................................................22 Appendix Limited warranty................................................................................................................23
Resumo do conteúdo contido na página número 6
Getting started Quick reference guide - Handset lifter ALERT ON/OFF SENSOR ADJ knob Turns the ring detector on or off. Adjusts the sensitivity When the ringer detector is turned of the ring detector off, the cordless headset does not (page 12). receive a call alert tone. Lifter arm STATUS light The light quickly Holds the corded telephone handset. flashes when there is an incoming call that the ring detector senses. The light flashes slowly when the switch hook presser is raised a
Resumo do conteúdo contido na página número 7
Getting started Quick reference guide - Handset lifter Small lifter pad Holds the earpiece of the corded telephone handset. Lifter arm height control Pushes / to adjust the height of the lifter arm. 2
Resumo do conteúdo contido na página número 8
Getting started Handset lifter installation The TL7000 handset lifter (lifter) works with the TL7610 or the TL7650 cordless headset to provide a complete communication solution. The lifter raises and lowers the handset to make and end phone calls. The ring detector provides an incoming call indica- tion through the cordless headset, so you can answer calls even if you are away from the telephone base. The lifter works with most corded telephones. Lifter installation Lifter arm 1. Make sur
Resumo do conteúdo contido na página número 9
Getting started Handset lifter installation 5. Pick up the lifter, turn it over, and peel the paper from the adhesive tape. 6. Carefully return the lifter to the same position that you noted before and press down. Adhesive tape 7. Follow the headset base installation steps on pages 6-10. 8. Remove the handset from your tele- ON/OFF phone. button 9. Press ON/OFF on the headset and listen for the dial tone. Make sure the switch hook presser is in its non-extended Motor condition. 10. Adj
Resumo do conteúdo contido na página número 10
Getting started Handset lifter installation 12. Place the telephone handset on the lifter arm. 13. Test to make sure the hook is cor- rectly operated by pressing the ON/OFF button on the headset. It may take some adjustments and testing to find the right position for the lifter. For the lifter to work properly, the switch hook must release completely when you press the ON/OFF button on the headset. The switch hook must also be pressed all the way when you press the ON/OFF button on the he
Resumo do conteúdo contido na página número 11
Getting started Handset lifter installation Connect the headset base The cords provided with your lifter have colored labels attached to help you plug them into the headset base. The back of the headset base has color-coded dots above the jacks, and the jacks’ names on the rear bottom plastic piece of the headset base that correspond to the colored labels on the cords (see Figure 1 below). You may attach the light blue label to the end of your telephone curly handset cord that you will plu
Resumo do conteúdo contido na página número 12
Getting started Handset lifter installation Before installing the headset base: Remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure 2). Figure 2 Install the headset base as shown on pages 9-10. After completing the headset base installation, slide the rear bottom piece towards the base until it clicks into place (as shown in Figure 3). Figure 3 7
Resumo do conteúdo contido na página número 13
Getting started Handset lifter installation 2 DSL filter 6 1 8 5 3 9 7 Color label (light blue) 4 Figure 4: The headset base connections (The numbers in this figure correspond to the steps on page 9.) NOTE: For complete instructions on using the headset base, please refer to the manual provided with your TL7610/TL7611/TL7650/TL7651 product, or visit www.telephones.att.com to download the manual. 8
Resumo do conteúdo contido na página número 14
Getting started Handset lifter installation Headset base installation with lifter (see Figure 4) 1. Plug one end of the telephone line cord (provided with your telephone) into the telephone jack. 2. Plug the other end of the telephone line cord into the wall jack. 3. Make sure the small end of the power adapter is plugged into the green POWER jack on the headset base. 4. Plug the large end of the power adapter into a power outlet not controlled by a wall switch. 5. Plug the lifter control
Resumo do conteúdo contido na página número 15
Getting started Handset lifter installation On Adjust lifter audio 1. Make sure that the LIFTER MODE light on the headset base is on. Press the MODE button on the headset base to change the mode. MODE 2. Put the headset next to your ear. (AT&T model TL7610/TL7611/TL7650/ ON/OFF TL7651). button 3. Press ON/OFF on the headset and listen for the dialing tone. If there is no dialing tone or buzzing noise, slide the LIFTER AUDIO ADJUST on the side of the headset base from A to G until the d
Resumo do conteúdo contido na página número 16
Getting started Ring detector installation The ring detector senses the telephone ringing and sends a call alert tone to the headset earpiece. Adhesive tape Ring detector’s sensor Ring detector plug Install the ring detector 1. Insert the ring detector plug into the RING DETECT jack on the lifter. RING DETECT jack Speaker 2. Remove the paper from the adhesive tape on the ring detector sensor. Adhesive tape 3. Stick the adhesive tape as close to the telephone speaker as possible. 11
Resumo do conteúdo contido na página número 17
Getting started Ring detector installation Adjust the sensitivity level The ring detector sensitivity level is designed to work with most corded telephones. However, the ring detector may need some adjustments to recognize less common telephone ring tones. To adjust the ring detector sensitivity while the telephone is ringing: • Turn the SENSOR ADJ knob clockwise to the right to increase the sensitivity. • Turn the SENSOR ADJ knob counterclockwise to the left to decrease the sensitiv
Resumo do conteúdo contido na página número 18
Getting started Ring detector installation • Press the ALERT ON/OFF button on the lifter to turn to the ring detector on or off. The STATUS light is blue if the ring detector is turned on. The STATUS light is red if the ring detector is turned off. • If you turn the ring detector off, the incoming alert tone is not sent to the headset(s). The ON/OFF light on the headset still flashes when there is an ON/OFF incoming call. button STATUS light • The light is blue when the lifter is not
Resumo do conteúdo contido na página número 19
Handset lifter operation Handset lifter operation After successful installation of the handset lifter, press the MODE button on the headset base until the LIFTER MODE light turns on. Make a call with the corded handset As indicated in the figure, lifting the handset causes the lifter arm to raise and release the switch hook. You will hear a dial tone through the handset. You can dial normally using the telephone dial pad. Release switch hook 14
Resumo do conteúdo contido na página número 20
Handset lifter operation Handset lifter operation Make and answer calls with the handset lifter and cordless headset You can use the cordless headset to make calls, answer calls and end calls without using the corded handset. Answer a call • Press ON/OFF on the headset to answer an incoming call. The switch ON/OFF hook presser on the lifter raises and button releases the switch hook on the corded telephone. You will hear the caller through the headset earpiece. Make a call 1. Press ON/
