Streszczenie treści zawartej na stronie nr. 1
AOC MONITOR
USER`S GUIDE
2236Swa
SAFETY INTRODUCTION…………………………………………………………….2
SETUP…………………………………………………………………………………….7
ADJUSTING…………….…………………………………………………...………….11
DRIVER INSTALLATION GUIDE…………………….….…………………………19
PRODUCT INFORMATION………………………………………………………….26
TROUBLESHOOT……...………………………………………………………….…..29
- 1 -
Streszczenie treści zawartej na stronie nr. 2
SAFETY INTRODUCTION FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance
Streszczenie treści zawartej na stronie nr. 3
Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. Read and follow these precautions when connecting and using your computer monitor: PRECAUTIONS • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If t
Streszczenie treści zawartej na stronie nr. 4
National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or lo
Streszczenie treści zawartej na stronie nr. 5
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand: - 5 -
Streszczenie treści zawartej na stronie nr. 6
CLEANING Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. OTHER If the product is emitting a strange smell, sound or smoke, disconnect the pow
Streszczenie treści zawartej na stronie nr. 7
SETUP CONTENTS IN BOX Not all signal cables (Analog, DVI, USB, Audio, and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation. - 7 -
Streszczenie treści zawartej na stronie nr. 8
SETUP STAND & BASE Please setup or remove the base following the steps as below. Setup: Remove: ADJUSTING VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. • Hold the stand so you will not topple the monitor when you change the monitor's angle. • You are able to adjust the monitor's angle from -5° to 20 ° NOTE: Do not touch the LCD screen when you change the angle. It may caus
Streszczenie treści zawartej na stronie nr. 9
CONNECTING MONITOR Cable Connections On Back of Monitor and Computer 1. Power 2. Analog (DB-15 VGA cable) 3.Audio To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3. Connect the audio cable to audio in port on the back of the monitor 4.
Streszczenie treści zawartej na stronie nr. 10
Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4. Insert the 4 screws into the holes and tighten.
Streszczenie treści zawartej na stronie nr. 11
The recommended resolution for this monitor is 1920 by 1080. To setup the monitor to this resolution, follow the steps below. For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization - 11 -
Streszczenie treści zawartej na stronie nr. 12
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. - 12 -
Streszczenie treści zawartej na stronie nr. 13
4 Click Appearance and Themes. 5 Double click DISPLAY. 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. - 13 -
Streszczenie treści zawartej na stronie nr. 14
HOTKEYS Power Press to turn on or turn off the monitor. 4:3 or wide / Up Press key to change the screen aspect ratio between standard 4 ：3format or Wide format. When the input resolution is wide format, the aspect ratio hotkey is disabled. When the main menu or sub-menu is active, the key functions as to select up or increase value. Auto / Down Auto configure hot key: When the OSD is closed, press Auto button to do auto configure. OSD SETTING
Streszczenie treści zawartej na stronie nr. 15
Eco mode ---DCR, Standard, Text, Internet, Game, Movie, Sports DCR Standard - 15 -
Streszczenie treści zawartej na stronie nr. 16
TEXT INTERNET Game - 16 -
Streszczenie treści zawartej na stronie nr. 17
Movie Sports Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as “On”, Contrast, Brightness, Eco mode and Gamma can not be adjusted. - 17 -
Streszczenie treści zawartej na stronie nr. 18
LED INDICATOR Status LED Color Full Power Mode Blue Active-off Mode Orange - 18 -
Streszczenie treści zawartej na stronie nr. 19
DRIVER INSTALLATION GUIDE Windows 2000 Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given bel
Streszczenie treści zawartej na stronie nr. 20
3. Select and click on the category ‘Appearance and Themes’ 4. Click on the 'Display' Item. 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button. Please follow the steps below. - 20 -
