Streszczenie treści zawartej na stronie nr. 1
LM929
LM929
19” LCD Monitor
User’s
Manual
By Envision Peripherals, Inc.
www.aocmonitor.com
Streszczenie treści zawartej na stronie nr. 2
LM929 TABLE OF CONTENTS Table of Contents 1 For Your Safety 2 Precautions 3 General Notes 4-5 Before You Operate The Monitor 6 Installation Instructions 7-13 Operating Instructions 14-19 Technical Support (FAQ) 19-21 Appendix 21-25 1
Streszczenie treści zawartej na stronie nr. 3
LM929 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins
Streszczenie treści zawartej na stronie nr. 4
LM929 PRECAUTIONS ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. ! Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and
Streszczenie treści zawartej na stronie nr. 5
LM929 GENERAL NOTES SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • • • • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • • • • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • • • • The LCD panel used in this monitor is a very high
Streszczenie treści zawartej na stronie nr. 6
LM929 GENERAL NOTES (cont) • • • • Plug & Play DDC 2B Feature - This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. 2 The DDC 2B is a bidirectional data channel based on the I C protocol. The host can request EDID information over the DDC 2B channel. • • This monito
Streszczenie treści zawartej na stronie nr. 7
LM929 BEFORE YOU OPERATE THE MONITOR FEATURES • 19” (48cm) TFT Color LCD Monitor • Crisp & Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @ 60Hz ® • EPA ENERGY STAR • 3W + 3W Stereo Speakers • Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Base Quick Start Guide (QSG) Monitor Warrabty Bookl
Streszczenie treści zawartej na stronie nr. 8
LM929 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Figure 1 - Installing the Base. INSTALLING THE BASE 1. Set the bottom base on a flat surface. 2. Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing the Base. REMOVING THE BASE 1. Never remove the base while the height adjustment lock pin is installed. Set the monitor standing on a flat firm surface.
Streszczenie treści zawartej na stronie nr. 9
LM929 INSTALLATION INSTRUCTIONS (Cont) POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into your LCD monitor’s AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC,
Streszczenie treści zawartej na stronie nr. 10
LM929 INSTALLATION INSTRUCTIONS (Cont) Connecting The Cables Figure 2 Connecting Cables 1. 15-pin D-SUB Cable 2. 24-Pin DVI Cable 3. Audio Cable 4. AC Power Cord Turn off your computer before performing the procedure below. 1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. (Optional – Requires a video card with DVI port) Connect one end of the 24-
Streszczenie treści zawartej na stronie nr. 11
LM929 INSTALLATION INSTRUCTIONS (cont) How To Install The INF & ICM Files • • This is a Plug & Play monitor. Microsoft Windows will automatically install • • a Plug & Play driver for it when you first install this monitor. It is not necessary to install the INF driver file included in the floppy diskette or CD if Microsoft Windows successfully installed a Plug & Play driver. If you would still like to install the driver included in the floppy diskette or CD that came with
Streszczenie treści zawartej na stronie nr. 12
LM929 INSTALLATION INSTRUCTIONS (cont) Height, Tilt, Pivot & Swivel Adjustment Your monitor features a multi-adjustable stand that will enable it move 110mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 90 degree landscape/portrait (pivot adjustment) and 70 degree side/side (swivel adjustment). To make an adjustment, grasp the monitor with both hands on the right and left edge of the casing and move it to the desired position. Figure 3
Streszczenie treści zawartej na stronie nr. 13
LM929 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (Not Included) This monitor can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Lay the monitor face down on a soft surface. 1. Remove the two rubber screw covers. 2. Remove the 2 screws that hold the plastic hinge cover. 3. Remove the plastic hinge cove
Streszczenie treści zawartej na stronie nr. 14
LM929 INSTALLATION INSTRUCTIONS (cont) Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws into the holes and tighten. 3. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instrucstions on attaching it
Streszczenie treści zawartej na stronie nr. 15
LM929 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls EXTERNAL CONTROLS 1. Power Button 4. < or Volume Button 2. MENU or ENTER Button 5. Auto Adjust or Exit Button 3. > or Volume Button • Power Button: Press this button to turn the monitor ON or OFF. • MENU / ENTER: This button will activate the OSD menu when OSD is OFF or activat
Streszczenie treści zawartej na stronie nr. 16
LM929 OPERATING INSTRUCTIONS (cont) • Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu. 2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. • Power Indicator: Green — Power On mode. Orange — Off mode. • Osd-Lock Function: To lo
Streszczenie treści zawartej na stronie nr. 17
LM929 OPERATING INSTRUCTIONS (cont) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 4). 2. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press < or > again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3. Press < or > to change the setting
Streszczenie treści zawartej na stronie nr. 18
LM929 OPERATING INSTRUCTIONS (cont) The descriptions for function control LEDS Main Main Sub Menu Sub Menu Menu Item Menu Reset Value Description Item Icon Icon Lumina Contrast Contrast from Recall Cool nce Digital-register. Contrast Value Brightness Backlight Recall Cool Adjustment Brightness Value Image Focus Adjust Picture Do Auto Config Setup Phase to reduce Horizontal-Line noise Clock Adjust picture Do Auto Config Clock to reduce Vertical-Line noise.
Streszczenie treści zawartej na stronie nr. 19
LM929 Select input signal Digital N/A from digital source (DVI) OSD H. Position Adjust the 50 Setup horizontal position of the OSD. V. Position Adjust the 50 verticalposition of the OSD. OSD Adjust the OSD 10 Timeout timeout. Langua English N/A Set OSD display The Language will ge language to be set to English. English. Deutsch N/A Set OSD display language to German. Français N/A Set OSD display language to French. Español N/A Set OSD display l
Streszczenie treści zawartej na stronie nr. 20
LM929 Reset Yes N/A Clear each old N/A status of Auto- configuration and set the color temperature to Cool. No N/A Do not execute N/A reset, return to main menu. Exit N/A N/A Exit OSD N/A 19