Streszczenie treści zawartej na stronie nr. 1
2217Pwc User Manual
1. Preface
About This Guide
This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to change without notice.
The sections are as follows:
• Safety Instructions: lists safety information.
• Setup: describes the initial setup process.
• Using the Monitor: gives an overview of how to use the monitor.
• Drivers: provides driver installation instructions for Windows.
• Technical Support : provides tips and solut
Streszczenie treści zawartej na stronie nr. 2
2. Safety Introduction FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordanc
Streszczenie treści zawartej na stronie nr. 3
Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. Read and follow these precautions when connecting and using your computer monitor: PRECAUTIONS • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If t
Streszczenie treści zawartej na stronie nr. 4
Adjusting Viewing Angle • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor's angle. • You are able to adjust the monitor's angle from -5°to 15°.
Streszczenie treści zawartej na stronie nr. 5
NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Audio 3. DVI 4. Analog 5. USB up 6. USB down x 3 Turn off your computer before performing the procedure below. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
Streszczenie treści zawartej na stronie nr. 6
Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm
Streszczenie treści zawartej na stronie nr. 7
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4. Insert the 4 screws into the holes and tighten. 5. Reconnect the cables. Refer to the user's manual that came with the o
Streszczenie treści zawartej na stronie nr. 8
1 Eco Mode / Up 2 Auto (Exit) / Left 3 Menu / Right 4 Volume 5 Power on/off 6 Camera 7 microphone Operation Steps 1) Press the MENU-button ( ) to activate the OSD window. 2) Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it. 3) Press or to change the settings of the selected function. Press or to select another func
Streszczenie treści zawartej na stronie nr. 9
OSD Settings • Press the MENU-button to activate the OSD window. • Press+ or - to navigate through the functions. Once the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub-menu, press or again to navigate through the sub-menu functions.Once the desired function is highlighted, press MENU-button to activate it. • Press+ or - to change the settings of the selected function. To exit and save, select the exit function. If you want to adjus
Streszczenie treści zawartej na stronie nr. 10
DCC: Dynamic color control ICM: Intelligent color management 1) How to use Color Boost? YCM adjustment: In addition to the basic R (red), G (green), B (blue) color adjustments, Color Boost has added Y (yellow), C (cyanine), and M (magenta) for more color fine-tuning options. YCM adjustments are in the third icon labeled "Color Temperature "in the OSD menu. When adjusting YCM values, RGB values will also be changed automatically due to the color correlation between RGB a
Streszczenie treści zawartej na stronie nr. 11
Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all colors become more vibrant. Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents human skin with more natural and truer colors. "Natural Skin" setting is ideal for viewing human portrait and detailed skin texture.
Streszczenie treści zawartej na stronie nr. 12
Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain landscape would look more natural and fresh. “Green Field” setting is ideal for watching mountain scenery and outdoor sports. Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will look more vivid and in-depth. "Sky Blue" setting is ideal for viewing sky and ocean images.
Streszczenie treści zawartej na stronie nr. 13
Auto Detect: When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively picture. Demo: Screen divided into two for demonstration purposes. 2) How to use Picture Boost? Users can change the color settings of a self-selected zone on the screen. The size and position of the selected zone can also be adjusted. "Picture Boost" is located in the fifth icon labeled "Picture Boost" in the OSD menu. Turn on "Bright Frame" to sele
Streszczenie treści zawartej na stronie nr. 14
Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations. DCR Adjustment What is DCR? Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in more depths. By increasing the darkness of the dark areas and the brightness of the bright areas, contrast ratio is uplifted to exceed 2000:1. DCR value varies subject
Streszczenie treści zawartej na stronie nr. 15
DCR Demos: Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations. Function Control Illustration Luminance Adjust Range Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Eco mode Standard Standard Mode Text Text Mode
Streszczenie treści zawartej na stronie nr. 16
Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports Mode Gamma1 Adjust to Gamma1 Gamma Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 Off Disable dynamic contrast ratio DCR On Enable dynamic contrast ratio Image Setup Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Focus 0-100 Adjust Picture Phase to reduce Horizontal-Line noise H.Position 0-100 Adjust the verticalposition of the picture. V.Position 0-100 Adjust the hor
Streszczenie treści zawartej na stronie nr. 17
OSD Setup H.Position 0-100 Adjust the verticalposition of OSD V.Position 0-100 Adjust the horizontal position of OSD Timeout 0-100 Adjust the OSD Timeout Language Select the OSD language Extra Digital Select Digital Sigal Source as Input Input Select Analog Select Analog Sigal Source as Input Auto Config yes or no Auto adjust the picture to default Reset yes or no Reset the menu to default DDC-CI Turn ON/OFF DDC-CI Support Information Show the information
Streszczenie treści zawartej na stronie nr. 18
9. Click on the 'Open' button, then click on the 'OK' button. 10. Select your monitor model and click on the 'Next' button. 11. Click on the 'Finish' button then the 'Close' button. If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button. Windows ME 1. Start Windows® Me 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'.
Streszczenie treści zawartej na stronie nr. 19
13. Click on the 'Finish' button then the 'Close' button. 14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box. Windows Vista 1. Start Windows® Vista 2. Click the Start button; select and click on 'Control Panel'. 3. Select and click on 'Hardware and Sound' 4. Choose 'Device Manager' and Click on 'Update device drivers'. 5. Select 'Monitor' and then right click on 'Generic PnP Monitor'. 6. Click on 'Update Driver Software'. 7. Select '
Streszczenie treści zawartej na stronie nr. 20
• The Computer Video Card should be snugly seated in its slot. • Make sure the monitor's video cable is properly connected to the computer. • Inspect the monitor's video cable and make sure none of the pins are bent. • Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. • Inspect the monitor's video cable and make sure that none of the pins arebent.
