Streszczenie treści zawartej na stronie nr. 1
REJ10J1870-0300
H8SX/1638 Group E6000H PLQP0120LA-A
User System Interface Board
HS1638ECN61H User’s Manual
Renesas Microcomputer Development Environment System
H8SX Family / H8SX/1600 Series
HS1638ECN61HE
Rev.3.00
Revision Date: Sep. 08, 2008
Streszczenie treści zawartej na stronie nr. 2
Rev. 3.00 Sep. 08, 2008 Page ii of iv REJ10J1870-0300
Streszczenie treści zawartej na stronie nr. 3
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this do
Streszczenie treści zawartej na stronie nr. 4
Rev. 3.00 Sep. 08, 2008 Page iv of iv REJ10J1870-0300
Streszczenie treści zawartej na stronie nr. 5
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. � KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. • User system inte
Streszczenie treści zawartej na stronie nr. 6
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole re
Streszczenie treści zawartej na stronie nr. 7
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. The Warranty is Void in the Following Cases: Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse, misapplication, neglect,
Streszczenie treści zawartej na stronie nr. 8
SAFETY PAGE READ FIRST � READ this user's manual before using this user system interface board. � KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an immi
Streszczenie treści zawartej na stronie nr. 9
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3. Always before
Streszczenie treści zawartej na stronie nr. 10
Rev. 3.00 Sep. 08, 2008 Page VI of VI REJ10J1870-0300
Streszczenie treści zawartej na stronie nr. 11
Preface The HS1638ECN61H is a user system interface board that connects a user system for the H8SX/1638 PLQP0120LA-A (former code: FP-120B) package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1638 group is only possible when this user system interface board is connected to the HS1650EPH60H.
Streszczenie treści zawartej na stronie nr. 12
Contents Preface ......................................................................................................................i Section 1 Configuration...........................................................................................1 Section 2 Connection Procedures............................................................................3 2.1 Connecting the User System Interface Board to the User System........................................ 3 2.1.1 Installing the IC S
Streszczenie treści zawartej na stronie nr. 13
Section 1 Configuration Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0120LA-A package. Please make sure you have all of these components after you have unpacked the box. Evaluation-chip board Screws (M2 × 6 mm) Spacer Screws (M2 × 10 mm) (for fastening the board) Socket cover User system interface board IC socket User system Figure 1 User System Interface Board for the PLQP01
Streszczenie treści zawartej na stronie nr. 14
Section 1 Configuration CAUTION Use an NQPACK120SE-ND socket and an HQPACK120SE cover (manufactured by Tokyo Eletech Corporation) for the PLQP0120LA-A-packaged IC socket on the user system. Table 1 HS1638ECN61H Components No. Component Quantity Remarks 1 User system interface 1 board 2 IC socket 1 For the PLQP0120LA-A package (to be mounted on the user system) 3 Socket cover 1 For installing a PLQP0120LA-A-packaged MCU 4 Screws (M2 x 10 mm) 4 For fastening the board 5 Screws (M
Streszczenie treści zawartej na stronie nr. 15
Section 2 Connection Procedures Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSON
Streszczenie treści zawartej na stronie nr. 16
Section 2 Connection Procedures To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. Use the guide pins provided with the product to dete
Streszczenie treści zawartej na stronie nr. 17
Section 2 Connection Procedures 2.1.2 Soldering the IC Socket After fastening, solder the IC socket for a PLQP0120LA-A package to the user system. CAUTION Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location of pin 1 before inserting. After checking the location of pin 1 on the user system interface board and
Streszczenie treści zawartej na stronie nr. 18
Section 2 Connection Procedures 2.1.4 Fastening the IC Socket Connector CAUTION 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error may be ca
Streszczenie treści zawartej na stronie nr. 19
Section 2 Connection Procedures Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 IC socket (NQPACK120SE-ND manufactured by User system Tokyo Eletech Corporation) Figure 3 Connecting the User System Interface Board to the User System Rev. 3.00 Sep. 08, 2008 Page 7 of 30 REJ10J1870-0300
Streszczenie treści zawartej na stronie nr. 20
Section 2 Connection Procedures 2.2 Exchanging the Spacers of the Evaluation-Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. Evaluation-chip board Spacer (2.6MP × 25 mm) Figure 4 Exchanging the Spacers Rev. 3.00 Sep. 08, 2008 Page 8 of