Streszczenie treści zawartej na stronie nr. 1
SH7046 Group FP-80Q
User System Interface Board
HS7046ECH61H User’s Manual
Renesas Microcomputer Development Environment System
TM
SuperH Family/SH7046 Series
Rev.4.00
2004.1.29
Streszczenie treści zawartej na stronie nr. 2
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflam
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. • User system interface boa
Streszczenie treści zawartej na stronie nr. 4
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of
Streszczenie treści zawartej na stronie nr. 5
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. The Warranty is Void in the Following Cases: Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse, misapplication, neglect, improper h
Streszczenie treści zawartej na stronie nr. 6
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an imminently hazardous
Streszczenie treści zawartej na stronie nr. 7
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3. Always before connecting any BOARDS, make sure that p
Streszczenie treści zawartej na stronie nr. 8
Preface The HS7046ECH61H is a user system interface board that connects a user system for the SH7046 FP-80Q package to the SH7046 E6000H emulator (HS7046EPH60H). i
Streszczenie treści zawartej na stronie nr. 9
Contents Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 Connecting User System Interface Board to User System ................................................3 2.1.1 Installing IC Socket..............................................................................................3 2.1.2 Installing Cable Head................
Streszczenie treści zawartej na stronie nr. 10
Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-80Q package. Please make sure you have all of these components when unpacking. EV-chip board Screws (M2.0 x 8 mm) with flat washers Screws (M2.0 x 12 mm) with flat washers Board Socket cover Spacer IC socket User system Figure 1 User System Interface Board for the SH7046 FP-80Q Package 1
Streszczenie treści zawartej na stronie nr. 11
CAUTION Use an IC149-080-017-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80Q package IC socket on the user system. Table 1 HS7046ECH61H Components No. Component Quantity Remarks With two spacers (2.6MP x 6 mm) 1 Board 1 2 IC socket 1 For the FP-80Q package (to be mounted on the user system) 3 Socket cover 1 For the FP-80Q package (for installing MCU) 4 Screws (M2.0 x 12 mm) 4 For fastening board (with four flat washers) 5 Screws (M2.0 x 8 mm) 4 For installing an FP-80Q-
Streszczenie treści zawartej na stronie nr. 12
Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. To con
Streszczenie treści zawartej na stronie nr. 13
2.1.2 Installing Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80Q package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 2. 2.1.3 Fastening Cable Head CAUTION 1. Use a Phillip-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accuratel
Streszczenie treści zawartej na stronie nr. 14
Screws (M2.0 x 12 mm) with flat washers Board Pin 1 IC socket (IC149-080-017-B5 manufactured by User system YAMAICHI ELECTRONICS Co., Ltd.) Figure 2 Connecting User System Interface Board to User System 5
Streszczenie treści zawartej na stronie nr. 15
2.2 Connecting User System Interface Board to EV-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. 2.
Streszczenie treści zawartej na stronie nr. 16
EV-chip board Connector No. EV-Chip Board Board Connector No. Connector No. UCN1 UCN1 UCN2 UCN2 Board Spacer User system Figure 3 Connecting User System Interface Board to EV-Chip Board 7
Streszczenie treści zawartej na stronie nr. 17
2.3 Recommended Dimensions for User System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-80Q package (IC149-080-017-B5: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 4 are somewhat different from those of the actual chip's mount pad. 20.50 min 14.70 max 0.65 × 19 = 12.35 ± 0.1 + 0.1 0.35 0.65 ± 0.05 - 0.05 Unit: mm Figure 4 Recommended Dimensions for Mount Pad
Streszczenie treści zawartej na stronie nr. 18
2.4 Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 5. 140.0 EV-chip board 100.0 19.5 31.0 33.5 16.0 User system interface board Unit: mm Spacer Tolerance: ±0.5 mm Figure 5 Dimensions for EV-Chip Board and User System Interface Board 9 69.0 5.0 34.5 29.5 92.0 116.0
Streszczenie treści zawartej na stronie nr. 19
2.5 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 6. EV-chip board 31.0 IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Spacer (ϕ6.0) 31.0 Unit: mm Tolerance: ±1.0 mm Figure 6 Resulting Dimensions after Connecting User System Interface Board 10 33.0 29.5 29.5 11.0 58.0
Streszczenie treści zawartej na stronie nr. 20
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error m
