Streszczenie treści zawartej na stronie nr. 1
IP-4MTS6B
(IP-4GMS6F)
Series
(Embedded Board)
INSTALLATION GUIDE
Installation Guide Revision A1
600700246BA10
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
© COPYRIGHT All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
Streszczenie treści zawartej na stronie nr. 4
CONTENTS SECTION 1 INTRODUCTION 1 1.1 Unpacking IP-4MTS6B / 4GMS6F Series 1 1.2 Description 3 1.3 Features 3 1.3.1 Graphic & Ethernet 3 1.3.2 Ultra ATA/66/100 4 1.3.3 Hardware Monitoring 4 1.3.4 I/O Shield Connector 4 1.3.5 Power-On/Off 5 1.3.6 IP-4MTS6B / IP-4GMS6F Series Overview 5 1.3.7 System Block Diagram 6 1.4 Specifications 7 1.5 Mechanical Dimensions 8 SECTION 2 INSTALLATIONS 9 2.1 System Installation 9 2.1.1 CPU Installation 9 2.1.2 H
Streszczenie treści zawartej na stronie nr. 5
CONTENTS SECTION 3 AWARD BIOS SETUP 33 3.1 BIOS Instructions 33 3.2 Main Menu 34 3.3 Standard CMOS Features 36 3.4 IDE Adapters 38 3.5 Advanced BIOS Features 40 3.6 Advanced Chipset Features 44 3.7 Integrated Peripherals 47 3.8 Power Management Setup 52 3.9 PnP/PCI Configurations 55 3.10 PC Health Status 57 3.11 Frequency/Voltage Control 58 3.12 Load Fail-Safe Default 59 3.13 Load Optimized Defaults 59 3.14 Supervisor/User Password Setting 60 3.15 Ex
Streszczenie treści zawartej na stronie nr. 6
iv
Streszczenie treści zawartej na stronie nr. 7
SECTION 1 INTRODUCTION 1.1 Unpacking IP-4MTS6B / 4GMS6F Series 1. Take out the IP-4MTS6B / 4GMS6F series unit from the carton box, check if the unit is properly secure in the plastic bag. 2. Check the contents of the carton box: Industrial board (IP-4MTS6B) Industrial board (IP-4GMS6F) ATA-66/100 HDD ribbon cable Floppy ribbon cable Installation guide Audio line-out cable 1
Streszczenie treści zawartej na stronie nr. 8
Introduction External K/B & M/S cable Driver CD (6-pins to 6-pins) Heat sink with fan Heat sink without fan (for IP-4MTS6B series) (for IP-4GMS6F series) I/O Shield 2
Streszczenie treści zawartej na stronie nr. 9
Introduction 1.2 Description The IP-4MTS6B series combines the high performance and exceptional ® value of Intel 855GME chipset with a full-featured, new generation, ® industrial board. The Intel advanced 855GME chipset support socket ® ® ® 479-pins Intel Pentium M / Celeron M processor of 1.3GHz and up to 2.0GHz (Dothan™ Core), that memory base on the FSB 400 MHz operation supports DDR SDRAM interface. In the meantime, the 855GME chipset integrated the LVDS & VGA function. The IP
Streszczenie treści zawartej na stronie nr. 10
Introduction Memory: - DDR SDRAM 200/266/333 - 1 x 184-pins DIMM socket, with support ECC - 1.0GB Max. IO Connectivity - ICH4: - 6 Hi-Speed USB2.0 ports - AC97 Audio Codec 1.3.2 Ultra ATA/66/100 The ICH4 provides two channel Ultra ATA/66/100 Bus Master IDE controller, that support Ultra ATA/66/100 protocols, perfect for such demanding applications as real-time video, multimedia, and high performance operating system. A new IDE cable is required for Ultra ATA/66/100. T
Streszczenie treści zawartej na stronie nr. 11
Introduction 1.3.5 Power-On/Off (Remote) The board has a single 20-pins connector for ATX power supplies. For ATX power supplies that support the Remote On/Off feature, this should be connected to the systems front panel for system Power On/Off button. The systems power On/Off button should be a momentary button that is normally open. The board has been designed with “Soft Off" functions. You can turn off the system from one of two sources: The first is the front panel Power O
Streszczenie treści zawartej na stronie nr. 12
Introduction 1.3.7 System Block Diagram Socket 479-pins for VRM Clock Intel Pentium M ADDR CTRL DATA 400MHz FSB LVDS or VGA DVI / CRT GMCH (855GME) DDR266/333 X1 Device 732 Micro FCBGA Dual Intel IDE Primary ATA100 Ac97 82541GI Audio 10/100/1000 IDE Secondary Codec Base-TX ICH4 421 BGA USB2.0 USB Port 1/2 PCI BUS USB Port 3/4 USB Port 5/6 Super I/O W83627HF FWH Keyboard Mouse COM Port LPT Port Floppy Figure 2: System Block Diagram ® IP-4GMS6F onboard Celeron M 600MHz without L2 c
Streszczenie treści zawartej na stronie nr. 13
Introduction 1.4 Specifications Processor: (IP-4MTS6B) ® ® - Support socket 479 Intel Pentium M with 1MB L2 cache processor, Speed at 1.1GHz ~ 1.7GHz (Banias™ core) ® ® - Support socket 479 Intel Pentium M with 2MB L2 cache processor, Speed at 1.5GHz ~ 2.0GHz (Dothan™ core) - System bus frequency at 400 MHz FSB ® ® - IP-4GMS6F onboard Intel Celeron M 600MHz (without L2 cache) Chipset: (IP-4MTS6B) ® - Intel 855GME + ICH4 AGPset ® - IP-4GMS6F used the Intel 852GM + ICH4 AGP
Streszczenie treści zawartej na stronie nr. 14
Introduction Rear I/O Connectors: - PS/2 mouse and PS/2 style keyboard - D-Sub 25-pins printer port connector D-Sub 9-pins COM1 serial port connector for RS-232 D-Sub 15-pins VGA connector - RJ-45 Ethernet (LAN1) and 2 x USB2.0 (USB 0/1) connectors - RJ-45 Ethernet (LAN2) and 2 x USB2.0 (USB 2/3) connectors Internal I/O Connectors (pin-header): - 2 x USB2.0 connectors (for optional USB cable with bracket) - Audio Line-out pin-header Power Connector: - 20-pins ATX power con
Streszczenie treści zawartej na stronie nr. 15
SECTION 2 INSTALLATIONS 2.1 System Installation 2.1.1 CPU Installation (IP-4MTS6B series) Carefully follow the steps below in order to install the CPU: 1. Check and confirm that you are going to install correctly CPU type and pin numbers (figure 3). 2. Take the screwdriver and releasing screw-nut of the socket 479. 3. Rotate mark of screw-nut to face the “OPEN”. 4. Align the pins of the CPU against the pinholes of the socket 479. Be sure to pay attention to the orie
Streszczenie treści zawartej na stronie nr. 16
Installations Removing a CPU: 1. Before removing the CPU, turn off the IP-4MTS6B series power; then wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools down. 2. Rotate mark of screw-nut to face the “OPEN”. 3. To remove the CPU. Note: The CPU and the heat radiation plate are hot. They may cause burns. To remove the CPU, reverse the installation steps. 2.1.2 Heat Sink Installation Make sure that good contact is made between t
Streszczenie treści zawartej na stronie nr. 17
Installations 2.1.3 Memory Module Installation Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIMMs have 184-pins and two notches, that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight down (figure 6) until it fits tightly into the DIMM socket. Figure 5: DIMM Memory and 184-pins Socket Figure 6: Memory I
Streszczenie treści zawartej na stronie nr. 18
Installations Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static electricity and damaging the DIMM, ground yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM. 2. Do not touch the connector of the DIMM. Dirt residue may cause a malfunction. 3. Hold the DIMM with its notch to the front side of the IP-4MTS6B series and insert it completely into the socket. A DIMM should be inserted into the inner
Streszczenie treści zawartej na stronie nr. 19
Installations 2.1.4 Setting Jumpers There are jumpers on the Embedded Board of the IP-4MTS6B series. You can set the jumpers to make the necessary operations. Figure 7: Jumper Connector For any three-pins jumpers (Figure 7), the jumper setting is 1-2 when the jumper connects pins 1 and 2. The setting is 2-3 when pins 2 and 3 are connected and so on. You see one of the lines surrounding a jumper, which indicates pin NO.1. To move a jumper from one position to
Streszczenie treści zawartej na stronie nr. 20
Installations 2.2 Board Layout IP-4MTS6B Jumper & Connector Location KB/MS 93004 IR-CONN VGA COM1 CN4 CN1 CN2 LAN1-LED LAN2-LED LPT1 CN5 JP1JP2 CN3 CN8 LAN2 LAN1 USB2/3 USB0/1 EXT. KB/MS CN6 CN7 CN12 COM2 CN9 JP6 CN11 LVDS-CONN CN10 USB4/5 JP4 BATT1 CN14 CN13 SYSTEM-FAN CPU-FAN DIMM1 LINE-OUT JP5 FLOPPY AUTO POWER ON CN15 IDE2 CN17 CN18 CN16 CD-IN CN21 -PW LED LOCK PW ON IDE1 CN19 CN20 SPKR +HDLED RESET ® IP-4GMS6F onboard Celeron M 600MHz without L2 cache processor. So the board l
