Streszczenie treści zawartej na stronie nr. 1
Product Manual
®
Momentus Blade Server
ST94811AB
100339697
Rev. B
August 2007
Streszczenie treści zawartej na stronie nr. 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100339697, Rev. B August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
Streszczenie treści zawartej na stronie nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 4
ii Momentus Blade Server Product Manual, Rev. B
Streszczenie treści zawartej na stronie nr. 5
List of Figures Figure 1. Momentus disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 3. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 4. Mounting dimensions—top, side and end view . . .
Streszczenie treści zawartej na stronie nr. 6
iv Momentus Blade Server Product Manual, Rev. B
Streszczenie treści zawartej na stronie nr. 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the Seagate Momentus™ Blade Server drive: � ST94811AB These drives provide the following key features: � 5,400-RPM spindle speed and 8 Mbytes combine for superior performance. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. � Tunneling Magnetoresistive (TMR) recording heads. � State-of-the
Streszczenie treści zawartej na stronie nr. 8
2 Momentus Blade Server Product Manual, Rev. B
Streszczenie treści zawartej na stronie nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST94811AB model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual. Table 1: Specifications Drive specification S
Streszczenie treści zawartej na stronie nr. 10
Table 1: Specifications (Continued) Drive specification ST94811AB Full-stroke seek (msec) 22 (typical); 26 (max) Seek power (typical) 2.4 watts Read/write power (typical) 2.4 watts Idle, performance mode (typical) 2.5 watts Standby mode 0.36 watts (typical)** Sleep mode 0.36 watts (typical)** Voltage tolerance (including noise) 5V ± 5% Ambient temperature 5° to 55°C (operating) –40° to 65°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative humi
Streszczenie treści zawartej na stronie nr. 11
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST94811AB 40 Gbytes 78,140,160 512 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.4 Physical organization Model Read/write heads Number of discs ST94811AB 2 1 2.5 Recording and interface tec
Streszczenie treści zawartej na stronie nr. 12
2.6 Physical characteristics Height (mm) 9.5 +/–0.2 (inches) 0.374 +/–0.0078 Width (mm) 69.85 +/–0.25 (inches) 2.75 +/–0.0098 Length (mm) 100.2 +/–0.25 (inches) 3.945 +/–0.0098 Typical weight (grams) 99 (pounds) 0.218 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both di
Streszczenie treści zawartej na stronie nr. 13
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/
Streszczenie treści zawartej na stronie nr. 14
2.9.1.1 Typical current profile +5 Volt Current during spindle start — Typical Amperes 1.2 1.0 0.8 Amps 0.6 0.4 0.2 0.0 4.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Seconds Figure 2. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at u
Streszczenie treści zawartej na stronie nr. 15
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 40°C (104°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 5° to 55°C (41° to 131°F) Nonoperating –40° to 65°C (–40° to 153°F) 2.10.2 Temperature gradient Operating 20°C per hour
Streszczenie treści zawartej na stronie nr. 16
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y, or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 225 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock lev
Streszczenie treści zawartej na stronie nr. 17
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second
Streszczenie treści zawartej na stronie nr. 18
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Mean time between failures 500,000 power-on hours (8,760 POH/year) At nominal power, 25°C ambient temperature. Max case temperature: 40°C at the case measurement location shown in Figure 4. Load/Unload (U/UL) 300,000 software-controlled power on/off cycles 25°C, 50% relative humidity 20,000 hard power on/off cycles 32°C, 80% relative humidity 100,000 software-controlled po
Streszczenie treści zawartej na stronie nr. 19
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para- graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil- ity (EMI/EMS) for Cla
Streszczenie treści zawartej na stronie nr. 20
14 Momentus Blade Server Product Manual, Rev. B
