Streszczenie treści zawartej na stronie nr. 1
Product Manual
TM
Pulsar
ST9200011FS
ST9100011FS
ST950011FS
100596473
Rev. A
April 2010
Streszczenie treści zawartej na stronie nr. 2
Revision history Revision Date Sheets affected or comments Rev. A 04/05/10 Initial release. © 2010 Seagate Technology LLC. All rights reserved. Publication number: 100596473, Rev. A. April 2010 Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Pulsar and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countr
Streszczenie treści zawartej na stronie nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary tables . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 4
ii Pulsar Product Manual, Rev. A
Streszczenie treści zawartej na stronie nr. 5
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 4. Air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 6
Streszczenie treści zawartej na stronie nr. 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate TM Pulsar model drives: ST9200011FS ST9100011FS ST950011FS These drives provide the following key features: • Single Layer Cell (SLC) NAND Flash storage. • High instantaneous (burst) data-transfer rates (up to 300MB/s). • Parallel flash access channels. • State-of-the-art on-the-fly error-correction algorithms. • Native Command Queueing with command ordering to increase perf
Streszczenie treści zawartej na stronie nr. 8
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels. The Serial ATA interface connects each drive in a point-to-point configuration with the Serial ATA host adapter. If two driv
Streszczenie treści zawartej na stronie nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST9200011FS ST9100011FS ST950011FS Product data communicated in this manual is specific only to the model numbers listed in this manual. The data listed in this manual may not be predictive of future generation specifications or requir
Streszczenie treści zawartej na stronie nr. 10
Drive specification ST9200011FS ST9100011FS ST950011FS Sustainable 4KB Random IOPs for 5 year Endurance 10,500 (65%/35% R/W 70% Duty Cycle) Startup current (typical) 5V (peak) 0.83 amps Voltage tolerance (including noise) 5V ± 5% 5° to 60°C (operating) Ambient temperature –40° to 70°C (nonoperating) 20°C (operating) Temperature gradient (°C per hour max) 20°C (nonoperating) 5% to 95% (operating) Relative humidity 5% to 95% (nonoperating) Relative humidity gradient 20% per hour max 37.7 (oper
Streszczenie treści zawartej na stronie nr. 11
2.2 Formatted capacity Model Formatted capacity* Guaranteed LBAs Emulated LBA Size (Bytes) ST9200011FS 200GB 390,721,968 ST9100011FS 100GB 195,371,568 512 ST950011FS 50GB 97,696,368 *One GB equals one billion bytes when referring to drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (LBAs) are consecutively numbered from 0 to n–1, where n is the number of guaranteed LBAs as defi
Streszczenie treści zawartej na stronie nr. 12
2.4.3 Performance Notes 200GB 100GB 50GB Maximum Burst Transfer Rate 300MB/s Peak sequential 128KB read/write data transfer rate (MB/s max) [1] 240/220 Sustained sequential 128KB read/write data transfer rate (MB/s) [2] 200/100 200/60 200/30 Peak 4KB random read/write command rate (IOPs) [3] 30,000/25,000 Sustained 4KB random read/write command rate (IOPs) [4] 25,000/5200 25,000/2600 Sustainable 4KB Random combined IOPS for 5 year Endurance [5] 10,500 (65%/35% R/W, 70% Duty Cycle) [1] Testing p
Streszczenie treści zawartej na stronie nr. 13
2.6 Access time Access measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Page-to-page access time is an average of all possible page-to-page accesses in both directions for a sequentially preconditioned drive. • Average access time is a true statistical random average of at least 5000 measurements of accesses between programmable pages, less overhead, on a random
Streszczenie treści zawartej na stronie nr. 14
2.8 Power specifications The drive receives DC power (+5V) through a native SATA power connector. See Figure 2 on page 20. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using +5V input voltage at 35°C ambient temperature. • Startup power Startup power is measured from the time of power-on to the time that the drive reaches operating condition and can pro
Streszczenie treści zawartej na stronie nr. 15
Table 2: 200GB DC power requirements Parameter 200Gb (3.0GB) Regulation +/‐5% Voltage +5 V Current (A) Power (W) Average Idle Current DCx 0.15 0.75 Standby DCx 0.11 0.55 Average Sleep Current DCx 0.11 0.55 Maximum Start Current: DC (Peak DC) 3σ 0.83 AC (Peak AC)
Streszczenie treści zawartej na stronie nr. 16
Table 3: 100GB DC power requirements Parameter 100Gb (3.0GB) Regulation +/‐5% Voltage +5 V Current (A) Power (W) Average Idle Current DCx 0.14 0.70 Standby DCx 0.11 0.55 Average Sleep Current DCx 0.10 0.50 Maximum Start Current: DC (Peak DC) 3σ 0.80 AC (Peak AC)
Streszczenie treści zawartej na stronie nr. 17
Table 4: 50GB DC power requirements Parameter 50Gb (3.0GB) Regulation +/‐5% Voltage +5 V Current (A) Power (W) Average Idle Current DCx 0.13 0.65 Standby DCx 0.11 0.55 Average Sleep Current DCx 0.09 0.45 Maximum Start Current: DC (Peak DC) 3σ 0.83 AC (Peak AC)
Streszczenie treści zawartej na stronie nr. 18
2.8.1.1 Typical current profiles Figure 1. Typical 5V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. • Using 5-volt power, the drive is expected to operate with a maximum of 250 mV peak-to-peak sine-wave injected noise at a frequency from 100Hz up to 20 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/w
Streszczenie treści zawartej na stronie nr. 19
2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 60°C (140°F) within the operating ambient conditions. Above 1000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters). Operating: 5° to 60°C (41° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.9.2 Temperature gradient Oper
Streszczenie treści zawartej na stronie nr. 20
2.9.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. 2.9.6.1 Operating vibration The maximum random vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. This specification does not cover connection issues that may result from testing at this level. 20–2000 Hz 16 Grms 2.
