Streszczenie treści zawartej na stronie nr. 1
Product Manual
®
Momentus Thin Series SATA
ST92503010AS
ST91603010AS
100586949
Rev. A
October 2009
Streszczenie treści zawartej na stronie nr. 2
Revision history Revision Date Sheets affected or comments Rev. A 10/21/09 Initial release. Copyright © 2009 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100586949, Rev. A August 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in
Streszczenie treści zawartej na stronie nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 4
ii Momentus Thin Series SATA Product Manual, Rev. A
Streszczenie treści zawartej na stronie nr. 5
List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 6
Streszczenie treści zawartej na stronie nr. 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus Thin Series SATA model drives: • ST92503010AS • ST91603010AS These drives provide the following key features: • 5400-RPM spindle speed. • 8-MB buffer. • Quiet operation. Fluid Dynamic Bearing (FDB) motor. • High instantaneous (burst) data-transfer rates (up to 3Gb/s). • Perpendicular recording technology. • State-of-the-art cache and on-the-fly error-correction alg
Streszczenie treści zawartej na stronie nr. 8
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels. In addition, Serial ATA makes the tran
Streszczenie treści zawartej na stronie nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST92503010AS and ST91603010AS models. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual. Table 1: Drive specifica
Streszczenie treści zawartej na stronie nr. 10
Table 1: Drive specifications Drive specification ST92503010AS ST91603010AS Read/write power (typical) Read: 1.4W; Write: 1.78W Idle mode, low power (typical) 0.58W Standby mode 0.20W (typical)*** Sleep mode 0.20W (typical)*** Voltage tolerance (including noise) +5V ± 10% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient 20°C (operating) (°C per hour max) 35°C (nonoperating) Relative humidity 5% to 95% (operating) 5% to 95% (nonoperating) Relative hum
Streszczenie treści zawartej na stronie nr. 11
2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST92503010AS 250 GB 488,397,168 512 ST91603010AS 160 GB 312,581,808 *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Sect
Streszczenie treści zawartej na stronie nr. 12
2.6 Physical characteristics Drive specification Height (mm) 6.8 +/-0.2 (in) 0.268 +/-0.0079 Width (mm) 69.85 +/-0.25 (in) 2.75 +/-0.0098 Length (mm) 100.35 +0.20/-0.25 (in) 3.951 +0.008/-0.010 Weight (max) ST92503010AS and ST91603010AS 92.0 g 0.203 lb 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an av
Streszczenie treści zawartej na stronie nr. 13
2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. • Seek mode During seek mode, the read/write actuator arm
Streszczenie treści zawartej na stronie nr. 14
2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Deferred spinup Momentus Thin Series SATA drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 2.9.3 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a m
Streszczenie treści zawartej na stronie nr. 15
2.9.5 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
Streszczenie treści zawartej na stronie nr. 16
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour
Streszczenie treści zawartej na stronie nr. 17
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock level t
Streszczenie treści zawartej na stronie nr. 18
2.11 Acoustics Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted sound power levels for steady state, idle, and active seek modes of operation. Table 5: Drive A-weighted Sound Power Levels (SWL, BA) Idle* Performance seek 2.0 bels (typ) 2.4 bels (typ) 2.2 bels (max) 2.5 bels (max) *During periods of drive idle, some offline activity m
Streszczenie treści zawartej na stronie nr. 19
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Annualized Failure Rate (AFR) <0.48% Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 600,000 software-controlled power on/off cycles 5°C, 80% relative humidity 20,000 hard power on/off cycles 5°C, 10% relative humidity 55°C, 16% relative humidity Warranty To determine
Streszczenie treści zawartej na stronie nr. 20
Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). 2.14.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually ma
