Instrukcja obsługi Metra Electronics MAZDA 6 2009 99-7511S

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7511S
APPLICATIONS
Mazda 6 2009
99-7511S
KIT FEATURES
• DIN Radio Provision
• ISO Mount Radio Provision
• Double DIN Radio Provision
• Stacked ISO Mount Radio Provision
• Painted To Match Silver Factory Dash
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) Filler Trim Panel • H) (2) #3 3/8” Phillips Screws
C
B
A
H
F
E G
D
TOOLS REQUIRED:
Small Flat Blade S

Streszczenie treści zawartej na stronie nr. 2

99-7511S TABLE OF CONTENTS Dash Disassembly - Mazda 6 2009 .... ... .... ... .... ... .... ... .... . . . . . . 1 Kit Assembly - DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN /Stacked ISO Mount Unit(s) Provision . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Streszczenie treści zawartej na stronie nr. 3

99-7511S DASH DISASSEMBLY MAZDA 6 2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the cup holder/parking brake trim panel. (Figure A) 3 Unclip and remove the trim panel above the glove box and down the right side of the center console. (Figure B) 4 Unclip and remove the trim panel next to the key switch and down the left B side of the center console. (Figure B) 5 Unclip and remove the trim panel surrounding the climate controls and

Streszczenie treści zawartej na stronie nr. 4

99-7511S KIT ASSEMBLY DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the filler trim panel to the back of the radio housing at the bottom edge. (Figure A) REAR OF RADIO HOUSING 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure B) FILLER TRIM PANEL 3 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure C) 4 Snap the pocket into the the bottom B opening o

Streszczenie treści zawartej na stronie nr. 5

99-7511S KIT ASSEMBLY ISO MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the filler trim panel to the back of the radio housing at the bottom edge. (Figure A) REAR OF RADIO HOUSING 2 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure B) FILLER TRIM PANEL 3 Slide the radio into the radio housing until it snaps into place. (Figure C) 4 Snap the Trim Plate onto the front of B the Radio Housing. (Figure

Streszczenie treści zawartej na stronie nr. 6

99-7511S KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNIT(S) PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the filler trim panel to the back of the radio housing at the bottom edge. (Figure A) REAR OF RADIO HOUSING 2 Cut and remove the center bar from the Radio Housing. (Figure B) 3 Snap the Double DIN brackets to the FILLER TRIM PANEL inside edge of the Radio Housing. (Figure C) B 4 Slide the Double DIN or stacked ISO mount unit(s) into the brac

Streszczenie treści zawartej na stronie nr. 7

99-7511S FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disa

Streszczenie treści zawartej na stronie nr. 8

99-7511S INSTRUCTIONS 1-800-221-0932 www.metraonline.com Rev. 01/13/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION NST99-7511S