Instrukcja obsługi Field Controls UV-AIRE UV-E

Streszczenie treści zawartej na stronie nr. 1

UV-AIRE™ AIR PURIFYING SYSTEM
Model: UV-E
(For use with 12”, 18” and 28” Field Controls Lamps)
(120/240 volt application)
ITEMS INCLUDED IN KIT:
1-UV-E power unit (NEMA3 housing)
1-Mounting Template
4-Sheet metal mounting screws
1-Angled mounting bracket
1-Flat mounting bracket
1-Instruction Sheet
1-Wing nut
2-Hex nuts
1-Lamp

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a
homes’ heating and air conditioning system. The treatment

Streszczenie treści zawartej na stronie nr. 2

I. GENERAL INFORMATION This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. There are different size units available, depending on the square footage of your home. See chart below for determining your homes needs. Minimum Max Air Lamp Intensity at 1 Recommended Lamp Length Duct Volts Amps Watts Temp Hz meter Max Sq. Feet Width °F 2 12” 9 120

Streszczenie treści zawartej na stronie nr. 3

WARNING: Disconnect electrical power supply before wiring 9. Connect to an appropriate power source such as an AC power disconnect box or to a circuit breaker panel. (See Figure 8) 10. Determine length of wire and conduit necessary according to power connection and install wiring conduit and water tight connector as shown in example figure 4. (Supplied by installer.) 11. Remove wiring access cover to expose terminal block. (Figure 5) Acces Cover Figure 4 Figure 5 12. Push power source w

Streszczenie treści zawartej na stronie nr. 4

15. Determine whether to use flat or angled bracket. (Refer to UV-Aire Configurations in Section III for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 10) Figure 10 b. Angled Bracket Installation NOTE: For angled bracket mounting, refer to specifications outlined by Diagram A for mounting distances in the “An

Streszczenie treści zawartej na stronie nr. 5

18. Swing securing bracket over end of lamp and hand-tighten the provided wing nut on stud. (See Figure 13) Figure 13 19. Plug ballast plug into end of lamp and reconnect power supply. (See Figure 14) Figure 14 20. Flip the red power switch to the on position. (Light on switch should be on indicating power.) 21. Look through view port to be sure lamp is working. You should see a blue glow. (The view port is covered with a plastic lens that blocks the UVC rays.) 22. If the lamp is not g

Streszczenie treści zawartej na stronie nr. 6

III. BULB MOUNTING BRACKET SELECTION AND INSTALLATION TM The UV-AIRE units come with an angled mounting bracket and flat mounting bracket to position the bulb either straight or at an angle. Choose one or the other bracket method best suited for your needs. Refer to the configurations chart below when making your selection. UV-Aire™ Configurations Good Better Standard 90° Installation Standard 90° Installation Patent Pending 45° Patent Pending 45° (Flat Bracket) (Flat Bracke

Streszczenie treści zawartej na stronie nr. 7

IV. MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2. Replace your UV-Aire™ Air Purifying System lamp once a year to maintain the lamps maximum output intensity. The lamp should operate continuously for maximum lamp life and light effectiveness. V. REPLACEMENT PROCEDURE VERY IMPORTANT: Turn switch on unit to ‘OFF’ position and disconnect from power source. 1. Remove wire tie or locking mechanism from latch on unit. 2. Unplug ballast plug from end of lamp. 3. Remove the wi

Streszczenie treści zawartej na stronie nr. 8

VIII. FLEX DUCT INSTALLATION For installations on duct systems with a metallic main duct and flex duct branches, follow the instructions in figure 15 below. Figure 15 Limited Warranty Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under normal use for eighteen (18) months from date of manufacturing by the consumer excepting the provisions numbered below. UV-LAMPS/BULBS Field Control