Streszczenie treści zawartej na stronie nr. 1
THE ADVANCED
D F - 3 0
DARK FLEET
GAMING FORCE
U S E R M A N U A L
Streszczenie treści zawartej na stronie nr. 2
DF-30 USER’S MANUAL Congratulations on your purchase of the Antec Dark Fleet DF-30. Meet the swifter, lighter Dark Fleet enclosure with the heavyweight feature set: the Dark Fleet DF-30. Up front sit two Fleet-Release™ access doors with tool-free washable fan filters, allowing rapid access to a massive array of drive bays – enough room for 11 total drives. Each Fleet-Release™ door comes standard with a variable- speed black 120 mm blue LED fan with stepless knob controls allowing precise
Streszczenie treści zawartej na stronie nr. 3
TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to know your case…………………………………………………. 5 1.2 Case specifications…………………………………………………………. 6 1.3 Before you begin…………………………………………………………… 7 1.4 Locating and positioning your computer…………………………………... 8 SECTION 2: HARDWARE INSTALLATION 2.1 Setting up…………………………………………………………………... 10 2.2 Motherboard installation…………………………………………………… 12 2.3 Standard ATX power supply installation…………………………………... 14 2.4 Cable management…………………………………………………………
Streszczenie treści zawartej na stronie nr. 4
SECTION 1 INTRODUCTION 4
Streszczenie treści zawartej na stronie nr. 5
1.1 GETTING TO KNOW YOUR CASE 5 4 10 1 6 8 2 7 7 9 3 Drive bays Hardware mounts 1 5.25” drive bays 8 Motherboard standoffs (pre- 2 3.5” drive bays installed) 3 2.5” internal SSD bay 9 Power supply mounts 4 2.5” external hot-swap 10 Front I/O ports Cooling 5 140 mm top TwoCool™ fan 6 120 mm rear TwoCool™ fan 7 Fleet-Release access door modules w/front variable- speed 120 mm b
Streszczenie treści zawartej na stronie nr. 6
1.2 CASE SPECIFICATIONS CASE TYPE Mid Tower COLOR Matte black 19.1″ (H) x 7.8″ (W) x 19.1″ (D) DIMENSIONS 485 mm (H) x 198 mm (W) x 486 mm (D) WEIGHT 15.1 lbs / 6.9 kg 1 x top 140 mm TwoCool™ fan COOLING 1 x rear white 120 mm TwoCool™ black-bladed fans with blue LED 2 x front variable-speed 120 mm black -bladed LED fans with blue LED 1 x side 120 mm fan for graphics cards (optional) DRIVE BAYS 6 x internal 3.5 ″ 3 x external 5.25 ″ 1 x top external 2.5 ″
Streszczenie treści zawartej na stronie nr. 7
1.3 BEFORE YOU BEGIN In order to ensure that your building experience with the Dark Fleet DF-30 will be a positive one, please take note of the following: • While working inside your Dark Fleet DF-30, keep your case on a flat, stable surface. Make sure your build area is clean, well-lit, and free of dust. • Antec cases feature rounded edges that minimize the occurrence of hand injuries. Nonetheless, exercise caution and control when handling case interiors. We strongl
Streszczenie treści zawartej na stronie nr. 8
1.4 LOCATING AND POSITIONING YOUR COMPUTER Your DF-30 has backwards- and top-facing exhaust fans, as well as front-mounted intake fans and one side- mounted front air intake. For optimum performance, we recommend leaving the front air intakes unobstructed. When open, the DF-30’s Fleet-Release™ doors take up an additional 15.5 cm of space in the front. Since loading and unloading the DF-30’s internal Fleet-Swap™ SATA bays through the doors will require opening and closing t
Streszczenie treści zawartej na stronie nr. 9
SECTION 2 HARDWARE INSTALLATION 9
Streszczenie treści zawartej na stronie nr. 10
2.1 SETTING UP Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. To remove the left and right side panels, remove these thumbscrews: Note: Place the panel thumbscrews aside carefully and remember where they are – they look very similar to the HDD cage thumbscrews, but they are NOT interchangeable. 10
Streszczenie treści zawartej na stronie nr. 11
Now rest your case with the left side up. Here’s what we’ll be working with first: E D B C A A – Power supply mounts B – 5.25” drive bay area C – 3.5” drive bay area D – Front panel wiring E – I/O panel Note: Do not use your fingernails to pry or lift the panels. Damage to the panels or injury to your fingernails may result. Note: This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult your motherboard manual for specific mounting
Streszczenie treści zawartej na stronie nr. 12
2.2 MOTHERBOARD INSTALLATION Before proceeding: - Check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard - Make sure you have the correct I/O panel for your motherboard. If the panel provided with the case isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. Make sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the road. 1. Lay the
Streszczenie treści zawartej na stronie nr. 13
3. Now remove your motherboard by lifting it up. Lift your motherboard out to install the standoffs. 4. Install standoffs as needed and put the motherboard back in. 5. Screw in your motherboard to the standoffs with the provided Phillips-head screws. Caution: Make sure to remove any unused motherboard standoffs. They may come into contact with the back of the motherboard and may electrify your case exterior if left connected. Step 5: Screwing in the motherboard after standoffs ar
Streszczenie treści zawartej na stronie nr. 14
Note: The DF-30 comes with a CPU cutout on the motherboard tray, which will allow you to change your CPU heatsink without removing the motherboard. 2.3 STANDARD ATX POWER SUPPLY INSTALLATION The DF-30 can accommodate a standard-size ATX power supply. 1. With the case upright, place the power supply on the bottom of the case. PSU resting on the standard PSU mount. 2. Push the power supply to the back of the case and align the mounting holes. 3. Attach the p
Streszczenie treści zawartej na stronie nr. 15
Use these screws to secure your power supply to the case. Note: Power supplies with fans on the bottom of the power supply will need to be mounted so that the fan is facing the top of the case. The DF-30 provides mounting holes for power supplies with standard mounting layouts to be installed right side up or upside down. 2.4 CABLE MANAGEMENT There is a cable management compartment behind the 3.5” drive cage. You can tuck or route excess cables in this compartment.
Streszczenie treści zawartej na stronie nr. 16
2.5 INTERNAL 3.5” DEVICE INSTALLATION The DF-30 includes two Fleet-Release™ access doors. With the front bezel facing you, they are located by default on the bottom nine drive bay slots (each door covers three drive bays). TM 1. Open the Fleet-Release access door. Opening the Fleet-Release™ access door by gently pressing the left side to release it, and then swing it open. 2. Insert your 3.5” device into the 3.5” drive cage from the front of the case. You will fe
Streszczenie treści zawartej na stronie nr. 17
Installing a 3.5” internal device 3. Fasten the device in place with the provided screws on both side of the drive cage. Make sure to install screws on the left side… …as well as the right side. 4. Mount any other 3.5” HDD devices accordingly. 5. Connect the appropriate power and data cables to the device(s), using cable routing as desired. 6. Close the Fleet-Release™ access door. 17
Streszczenie treści zawartej na stronie nr. 18
2.6 EXTERNAL 3.5” DEVICE INSTALLATION There is one external 3.5” drive bay under the 5.25” drive bays. Remove this drive bay cover. 1. Carefully remove the 3.5” drive bay cover from the bezel. Load the drives from the front, lining them up to the front of the drive cage. Insert your drive as shown. 2. With one hand supporting the drive, fasten the drive with the screws provided. 3. Find a small 4-pin white connector on the power supply and connect it to the male 4-pin connect
Streszczenie treści zawartej na stronie nr. 19
2.7 USING THE TOP 2.5” HOT-SWAP BAY The DF-30’s top 2.5” hard drive bay is hot-swap capable. To use the hot-swap feature, ensure that your motherboard is configured for hot-swap. Make sure to install all related drivers that come with your motherboard and turn on the AHCI function in the BIOS to activate the hot swap feature. Using the top 2.5” hot-swap drive bay A. LOADING: 1. Align your SATA HDD with the drive bay with the connector facing the case. 2. Push the HDD
Streszczenie treści zawartej na stronie nr. 20
2.8 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Before you begin, remove both side panels. 1. First, remove the drive bay faceplate and metal cover plate as shown below. The plastic drive bay faceplate should pop free. A screwdriver may be needed to remove the metal cover plate. 2. Slide your 5.25” device into the bay from the front of the case. 5.25” device installation 3. Secure the drive into position in the dr
