Streszczenie treści zawartej na stronie nr. 1
User Guide
Architectural Connectivity
HSA 822
®
Hideaway Surface Access Enclosure
Extron USA - West Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East
Headquarters
+800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +400.883.1568 +971.4.2991800
+800.633.9876
Inside USA and Inside Europe Only Inside Asia Only +81.3.3511.7656 FAX Inside China Only +971.4.2991880 FAX
Inside USA and
Canada Only
Canada Only
+31.33.453.4040 +65.6383.4400 +86.21.3760.1568
Streszczenie treści zawartej na stronie nr. 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended This symbol is intended to alert the user of important to be used with a main power system with a grounded (neutral) Extron® Warranty operating and maintenance (servicing) instructions in the conductor. The third (grounding) pin is a safety feature, do not literature provided with the equipment. attempt to bypass
Streszczenie treści zawartej na stronie nr. 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电池。
Streszczenie treści zawartej na stronie nr. 4
Contents Maintenance and Modifications .17 Introduction .......................................1 About the HSA 822 Replacing an AAP .............................17 Hideaway Enclosure .........................1 Replacing the Bezels ........................19 Features ..............................................3 Removing and Replacing the Enclosure ..................................20 Replacing the Gas Lift ......................23 Installation .........................................5 Adjust
Streszczenie treści zawartej na stronie nr. 5
Introduction This section gives an overview of the Extron HSA 822 Hideaway Enclosure Series and describes its features. Topics that are covered include: • About the HSA 822 Hideaway Enclosure • Features About the HSA 822 Hideaway Enclosure The HSA 822 is a furniture-mounted, architectural solution for inconspicuous computer video interface connector access and control. The HSA 822 provides space for four double space (double-height) or eight single space Extron Architectural Adapter Plates
Streszczenie treści zawartej na stronie nr. 6
AUDIO IS NE PL U E T CT COMPUTER INPUTS SOG V-SYNC WIDTH AUDIO ANALOG C AO N B T CR O D L E VIDEO OUTP SU E DR D T R SP NC EG O M SP Y S NC YNC LEVEL PEAKING RGB 580xi AUD O I S IN EP LE UT CT COMPUTER With an optional conversion kit, one or more of the RJ-45 (data) lines Features can be converted to an RJ-11 (telephone) line. • UL/c-UL listed The installed enclosure fits nearly flush within a table or podium top, • CSA certified storing the AAPs and connectors out of the way and out of
Streszczenie treści zawartej na stronie nr. 7
Installation This section describes installation of the HSA 822, including connections and features. Topics that are covered include: • Installation Overview • Preparing the Routing Template • Preparing the Table and Mounting the Enclosure • Cabling and Installing the AAPs • Cabling the Enclosure • Routing the AAP Cables • Bezels Installation Overview Install and set up the HSA 822 as follows: 1 If desired, install the optional flexible conduit kit to replace the removable AC power c
Streszczenie treści zawartej na stronie nr. 8
Width of Mounting Surface Preparing the Routing Template Preparing the Table and Mounting the Enclosure Extron offers a metal routing template for the HSA 822, The preferred and recommended method for preparing the table is to part number 70-191-01. Extron recommends using this template as a use the appropriate Extron metal routing template and a router. guide to cut the hole in the table where the HSA will be installed. Alternatively, you can use a paper cut-out template (see “Reference Inf
Streszczenie treści zawartej na stronie nr. 9
AUDIO INPUT SELECT COMPUTER CAUTION: Do not use isopropyl alcohol or other solvents to clean the HSA. Strong solvents will ruin some finishes. 8. From the underside of the table, bolt the clamshell to the enclosure with two bolts of optimum length (included) (see figure 5). 9. Peel any remaining protective coating from the enclosure. HSA 822 Figure 4. Cutting the Opening with a Router WARNING: Wear safety glasses when operating the router. Failure to comply can result in eye injury. 4. Us
Streszczenie treści zawartej na stronie nr. 10
HSA 822 AUDIO INPUT COMPUTER SELECT HSA 822 2. Cable the rear of the AAPs before fastening the AAPs to the Cabling and Installing the AAPs AAP panel. Route the cables through the hole in the underside of the surface mount enclosure and connect them to the rear of NOTE: The online Connectivity Configurator, available at the AAPs. If applicable, refer to the cabling information in the www.extron.com, offers guidance as to the fit of AAPs documentation for the AAP. into this space. 3. Inser
Streszczenie treści zawartej na stronie nr. 11
Cabling the RJ-45 connectors Cabling the Enclosure Plug one end of a CAT 6 twisted pair (TP) cable into each of these RJ-45 female connectors. Connect the other end to an appropriate Bottom Panel Features telecommunications or data network or to an Extron TP product. 3 NOTE: All RJ-45 connectors are terminated in accordance with the TIA/EIA T 568 A standard. 2 When cabling the AAP panels and the bottom panel, the bottom RJ-45 connectors match up with the AAP panel RJ-45 connectors as 1 sh
Streszczenie treści zawartej na stronie nr. 12
Routing the AAP Cables Bezels The AAP cables must have freedom of movement to permit opening The HSA 822 ships with RJ-45 connector bezel plug-ins in a variety of and closing the surface mount enclosure. At the same time, they need colors and a black, blank bezel. Bezel to be restrained to prevent them from rubbing against the edges of To change to a different color RJ-45 connector bezel the enclosure cable access hole in the underside of the surface mount or if an RJ-45 connector is not n
Streszczenie treści zawartej na stronie nr. 13
Maintenance and Modifications This section describes modifying and maintaining the HSA 822 surface mount enclosures. Most of the maintenance procedures require removing the surface mount enclosure from the table. Topics that are covered include: • Replacing an AAP • Replacing the Bezels • Removing and Replacing the Enclosure • Replacing the Gas Lift • Adjusting the Top Surface Replacing an AAP Replace one or more AAPs as follows: WARNING: Ensure that AC power is disconnected before s
Streszczenie treści zawartej na stronie nr. 14
HSA 822 AUDIO INPUT COMPUTER SELECT HSA 822 AUDIO INPUT COMPUTER SELECT 7. Replace the AAP panel in the surface mount enclosure and secure them in place with the screws removed in step 2. If you lose an Remove two AAP panel screw, four spare screws are stored in the underside of screws ea. side. the enclosure (see figure 8 on page 12). 8. To prevent wear and tear caused by cable movement, secure the AAP cables underneath the table (see “Routing the AAP Cables” on page 14. Replacing the Be
Streszczenie treści zawartej na stronie nr. 15
Removing and Replacing the Enclosure CAUTIONS: • The flanged edges of the top of the surface enclosure are bevelled to an ultra-fine thickness of The procedures for replacing the gas lift and adjusting the levelling less than 0.04 (4/100) inch (approximately 1 mm). of the top surface require removing the HSA 822 from the table. These edges are soft and can be easily nicked Remove and replace the surface mount enclosure for maintenance as or bent. Exercise caution when handlin
Streszczenie treści zawartej na stronie nr. 16
AUDIO INPUT COMPUTER SELECT Replacing the Gas Lift The gas lift that raises the surface is rated for 100,000 opening and closing cycles. An enclosure with many cables connected or HSA 822 an enclosure with a brass top panel may require a stronger gas Enclosure lift than the standard 10 lb lift. Contact the Extron S3 Sales and Technical Support Hotline at the nearest phone number listed on the rear cover of this guide to obtain a replacement gas lift. Remove (16) Replace the gas lift as fo
Streszczenie treści zawartej na stronie nr. 17
4. Open and close the top panel as necessary to access the CAUTION: With the top panel bracket detached from the center lifting platform (see figure 17). Remove the four lifting platform, the bracket will be loose atop screws that secure the top panel bracket to the lifting platform. the gas lift. Ensure that the bracket does not contact the top flange. Marring of the soft surface of the flange may result. 5. Turn the enclosure frame rightside-up. Top Panel 6. Remove and retain the 9/32-
Streszczenie treści zawartej na stronie nr. 18
AUDIO INPUT COMPUTER SELECT Adjusting the Top Surface The top lifting panel of the HSA 822 can be adjusted to raise or lower its level flush with the flange. It can also be adjusted to ensure that the lifting panel is horizontal and not tipped. Adjusting the Height of the Top Surface NOTE: You may be able to adjust the height of the top lifting panel without removing the HSA 822 from the table. If you can reach the height adjustment lock screw slots (see figure 18) in the side of the encl
Streszczenie treści zawartej na stronie nr. 19
Adjusting the Top Surface Level Reference Information The top lifting panel of the HSA 822 can be adjusted to ensure that the lifting panel is horizontal and not tipped. Level the lifting panel of the HSA 822 as follows: 1. Remove the surface mount enclosure from the table. See “Removing and Replacing the Enclosure”, steps 1 through 9. Place This section provides additional reference information for the the enclosure on a horizontal surface. To protect the finish, place HSA 822. Topics c
Streszczenie treści zawartej na stronie nr. 20
Template, Replacement Parts, and Accessories Part Part number HSA 822 routing template 70-191-01 HSA 822 standard (10 lb) gas lift 70-193-01 HSA 822 RJ-11 cable kit 70-226-01 HSA 822 flexible conduit adapter kit 70-228-01 A Interface Accessories Part Part number C RGB 580xi 60-362-01 B RGB 580xi AAP 3' (6') (black) 70-128 (129) -02 RGB 580xi S AAP 3' (6') (black) 70-134 (135) -02 Figure 21. Clamshell Dimensions RGB 580xi SI AAP 6' (black) 70-138-02 Part Numbers Top Plate Dimensions HSA 822 Par
