Streszczenie treści zawartej na stronie nr. 1
24" (61 CM) GAS WASHER/DRYER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER/DRYER SAFETY ..............................1 Remove Foam Packing..................................8
Connect Drain Hose.......................................8
INSTALLATION INSTRUCTIONS ....................2
Tools and Parts..............................................2 Connect Inlet Hoses ......................................8
Secure Drain Hose.........................................9
Alternate Parts ............
Streszczenie treści zawartej na stronie nr. 2
WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Clear the room, building, or area of all occupants. • Immediat
Streszczenie treści zawartej na stronie nr. 3
Parts supplied: Remove parts package from the washer basket. Check that all Location Requirements parts were included. WARNING A B C D E Explosion Hazard A. Rear leveling legs (2) D. Plastic strap Keep flammable materials and vapors, such as B. Front leveling legs (2) E. Silver double-wire hose clamp gasoline, away from dryer. C. Drain hose Failure to do so can result in death, explosion, or fire. Parts needed: Check local codes and with gas supplier, check existing gas You will need supply,
Streszczenie treści zawartej na stronie nr. 4
Washer/Dryer Dimensions Mobile home installations require: Metal exhaust system hardware, which is available for 3 15 ⁄8" purchase from your dealer. (391 mm) Mobile Home Installation Kit Part Number 346764. See “Tools and Parts” section for information on ordering. Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening. 71 ¾" (1822 mm) Drain System The washe
Streszczenie treści zawartej na stronie nr. 5
Electrical Requirements Gas Supply Requirements WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this appliance be p
Streszczenie treści zawartej na stronie nr. 6
Must include a shutoff valve: An individual shutoff valve must be installed within Venting Requirements six (6) feet (1.8 m) of the washer/dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The location should be easy to reach for opening and closing. WARNING A B Fire Hazard C Use a heavy metal vent. D Do not use a plastic vent. Do not use a metal foil vent. A. Gas shutoff valve Failure to follow these instructions can result in death 1 B. ⁄8" NPT minimum plugged tappi
Streszczenie treści zawartej na stronie nr. 7
Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor Install Leveling Legs performance. Do not install flexible metal vent in enclosed walls, ceilings, or floors. WARNING The total length of flexible metal vent should not exceed 3 Excessive Weight Hazard 7 ⁄4 ft (2.4 m). Elbows Use two or more people to move and install washer/dryer. 45° elbows provide better airflow than 90° elbows. Failure to do so can result in back or other injury. T
Streszczenie treści zawartej na stronie nr. 8
For laundry tub or standpipe drain systems 1. Make sure drain hose form is in correct position. Remove Foam Packing 1. Open the washer lid. The latch under the dryer will keep the lid open. A 2. Pull the foam packing ring out of the washer. A. Drain hose form NOTE: Keep the foam ring and use it when transporting your 2. Put the hooked end of drain hose into laundry tub or washer/dryer. This packing material is used to keep the washer standpipe. Rotate hook to eliminate kinks. tub stable durin
Streszczenie treści zawartej na stronie nr. 9
Connect the inlet hoses to the washer 1. Attach the hot water hose to the bottom inlet valve. Attaching Secure Drain Hose the hot water hose first makes it easier to tighten connection 1. Move the washer/dryer to its final location and remove any with pliers. cardboard used to move the washer/dryer. 2. Screw on coupling by hand until it is seated on the washer. 2. Locate the plastic strap included in the parts package. 3. Using pliers, tighten the couplings with an additional two- thirds turn
Streszczenie treści zawartej na stronie nr. 10
Optional exhaust installations NOTE: The following kits for close clearance alternate installations are available for purchase. Please reference the “Assistance or This washer/dryer can be converted to exhaust out the right Service” section of the Washer/Dryer User Instructions. or left side. To convert the washer/dryer, use Side Exhaust Kit Part Number 279823. If your washer/dryer was previously Over-the-Top Installation: exhausted from the right or left side, it can be converted to rear
Streszczenie treści zawartej na stronie nr. 11
Vent system chart 3. Install the adapter on the ½" rigid gas supply pipe using pipe- joint compound. NOTE: Side exhaust installations add a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart. Number of Type of Vent Box or Angled A 90º turns Louvered hoods B or elbows hoods C 0 Rigid metal 43 ft (13.1 m) 36 ft (11.0 m) D E 1 Rigid metal 33 ft (10.1 m) 26 ft (7.9 m) 2 Rigid metal 23 ft (7.0 m) 16 ft (4.9 m) A. ½" rigid gas supply pipe B. Use pipe-joint
Streszczenie treści zawartej na stronie nr. 12
Complete Installation 1. Check that all parts are now installed. If there is an extra part, 7. Check that the water faucets are on. go back through the steps to see which step was skipped. 8. Check for leaks around faucets and inlet hoses. 2. Check that you have all of your tools. 9. Remove the blue protective film on the console and any tape 3. Dispose of/recycle all packaging materials. Keep the plastic remaining on the washer/dryer. foam for use if the washer/dryer should be transported. 10.
