Streszczenie treści zawartej na stronie nr. 1
A
N
S
A
S
C
C
O
N
E
I
G
R
C
I
R
T
®
VENT-FREE PROPANE GAS HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
Model: CGP11
WARNING: If the information in this manual WARNING: Improper installation,
is not followed exactly, a fire or explosion
adjustment, alteration, service, or
may result causing property damage, per-
maintenance can cause injury or
sonal injury, or loss of life.
property damage. Refer to this
— Do not store or use gasoline or other
manual for correct installation and
flammable vap
Streszczenie treści zawartej na stronie nr. 2
SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Local Codes ................................................................................... 4 Unpacking...................................................................................... 4 Product Features ............................................................................
Streszczenie treści zawartej na stronie nr. 3
SAFETY ! WARNINGS Continued WARNING ICON G 001 1. Use only propane gas. Do not convert heater to use different fuel type. INFORMATION 2. Do not place propane supply tank(s) inside any structure. Locate propane Continued supply tank(s) outdoors. 3. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electrical switch; do not use any phone in your building • immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions
Streszczenie treści zawartej na stronie nr. 4
Control Knob PRODUCT IDENTIFICATION Grill Guard Burners Heater Front Cabinet Panel Figure 1 - Vent-Free Propane Gas Heater Install and use heater with care. Follow all local codes. In the absence of local LOCAL CODES codes, use the latest edition of the National Gas Code ANSI Z223.1, also known as NFPA 54*. *Available from: American National Standards Institute, Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc. Batterymarch Park Quincy, MA 02269 1. Remove heater
Streszczenie treści zawartej na stronie nr. 5
INSTALLING NOTICE TO WALL A qualified service person must install heater. Follow all local codes. CHECK GAS TYPE Use only propane gas. If your gas supply is not propane, do not install heater. Call dealer where you bought heater for proper type heater. INSTALLATION ITEMS Before installing heater, make sure you have the items below: • external regulator (supplied by • ground joint union installer-see page 9) • test gauge connection * (see • piping (check local codes) Figure 11, page 10) • sealant
Streszczenie treści zawartej na stronie nr. 6
For convenience and efficiency, install heater • where there is easy access for operation, inspection, and service • in coldest part of room CEILING 36" Minimum 8" Minimum From Sides Of Heater Right Side Left Side 3" Minimum To Top Surface Of Carpeting, Tile Or Other Combustible Material FLOOR Figure 2 - Mounting Clearances As Viewed From Front of Heater INSTALLING HEATER TO WALL Marking Screw Locations 1. Determine where you will locate heater. ! WARNING WARNING ICON G 001 Maintain minimum cl
Streszczenie treści zawartej na stronie nr. 7
Installing Two Mounting Screws Note: Wall anchors and mounting screws are in hardware package. The hardware package is provided with heater. Attaching to wall stud method For attaching mounting screw to wall stud 1. Drill hole at marked location using 9/64" drill bit. 2. Insert mounting screw into wall stud. 3. Tighten screw until 1/16" space (thickness of penny) is between screwhead and wall. Attaching to wall anchor method Follow instructions below to attach mounting screws to hollow walls (wa
Streszczenie treści zawartej na stronie nr. 8
Placing Heater On Mounting Screws 1. Locate two keyhole slots on back panel of heater (see Figure 7). 2. Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots. Keyhole Slots Figure 7 - Location Of Keyhole Slots On Back Panel Of Heater Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel. 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forw
Streszczenie treści zawartej na stronie nr. 9
CONNECTING NOTICE TO GAS A qualified service person must connect heater to gas supply. Follow all local codes. SUPPLY ! CAUTION WARNING ICON G 001 Never connect heater directly to the propane supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane supply. The installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure between 11 and 14 inches o
Streszczenie treści zawartej na stronie nr. 10
IMPORTANT: Hold pressure regulator with wrench when connecting it to gas piping and/or fittings. Pressure Regulator 3/8" NPT Heater Pipe Nipple Cabinet Ground Joint Union Tee Joint Manual Shutoff Reducer Test Valve * Bushing to Gauge 1/8" NPT Connection * From External 1/8" NPT Regulator Plug Tap (11" W.C. to Tee 14" W.C. Pressure) Joint 3" Minimum Sediment Trap Pipe Nipple Cap Figure 11 - Gas Connection * An A.G.A. design certified manual shutoff valve with 1/8" NPT tap is an acceptable alter
Streszczenie treści zawartej na stronie nr. 11
3. Pressurize supply piping system by either using compressed air or opening propane supply tank valve. 4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak. 5. Correct all leaks at once. Test Pressures Equal To or Less Than 1/2 PSIG 1. Close manual shutoff valve (see Figure 12). 2. Pressurize supply piping system by either using compressed air or opening propane supply tank valve. 3. Check all joints from propane supp
Streszczenie treści zawartej na stronie nr. 12
FOR YOUR SAFETY READ BEFORE LIGHTING OPERATING HEATER ! WARNING WARNING ICON G 001 If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the
Streszczenie treści zawartej na stronie nr. 13
4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you then smell gas, STOP! Follow “B” in the safety information at the top of page 12. If you don’t smell gas, go to the next step. 5. Press in control knob. Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system. • If control knob does not pop up when rele
Streszczenie treści zawartej na stronie nr. 14
TO SELECT HEATING LEVEL ! WARNING WARNING ICON G 001 When running heater, set control knob at LOW or HIGH locked positions. Never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result. ! CAUTION WARNING ICON G 001 Do not try to adjust heating levels by using the manual shutoff valve. C-clockwise 1. Slightly press in control knob and turn counterclockwise to the LOW or HIGH positions. IMPORTANT: Release downward pressure while turning control
Streszczenie treści zawartej na stronie nr. 15
TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise to the OFF position. Clockwise Shutting Off Burner Only (pilot stays lit) 1. Turn control knob clockwise to the PILOT position. Clockwise MANUAL LIGHTING PROCEDURE 1. Remove front panel (see Figure 8, page 8). 2. Follow steps 1 through 6 under LIGHTING INSTRUCTIONS, pages 12 and 13. 3. With control knob pressed in, strike match. Hold match to pilot until pilot lights. 4. Keep control knob pressed in for 10 seconds
Streszczenie treści zawartej na stronie nr. 16
BURNER FLAME PATTERN Figure 19 shows a correct burner flame pattern. Figure 20 shows an incorrect burner flame pattern. Figure 19 - Correct Burner Flame Pattern Figure 20 - Incorrect Burner Flame Pattern If burner flame pattern is incorrect, as shown in Figure 20 • turn heater off (see TO TURN OFF GAS TO APPLIANCE, page 15) • see TROUBLESHOOTING, pages 17 through 20 16
Streszczenie treści zawartej na stronie nr. 17
CLEANING ! WARNING WARNING ICON G 001 AND Turn off heater and let cool before cleaning. MAINTENANCE ! CAUTION WARNING ICON G 001 You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, etc. ODS/PILOT AND BURNER ORIFICE • Use a vacuum cleaner, pressurized air, or small
Streszczenie treści zawartej na stronie nr. 18
OBSERVED POSSIBLE PROBLEM CAUSE REMEDY When control knob is 1. Gas supply turned off or 1. Turn on gas supply or pressed in and turned manual shutoff valve open manual shutoff to the PILOT/IGN po- closed valve sition, there is spark at 2.Control knob not 2. Press in control knob ODS/pilot but no igni- pressed in while being while turning to PILOT/ tion turned to PILOT/IGN IGN position position 3. Air in gas lines when 3. Continue holding down installed control knob. Repeat ig- niting operation u
Streszczenie treści zawartej na stronie nr. 19
OBSERVED POSSIBLE PROBLEM CAUSE REMEDY Burner(s) does not 1. Burner orifice(s) is 1. Clean burner orifice(s) light after ODS/pilot is clogged (see CLEANING AND lit MAINTENANCE, page 17) or replace burner orifice(s) 2. Burner orifice(s) di- 2. Replace burner orifice(s) ameter is too small 3. Inlet gas pressure is too 3. Contact local propane gas low company Delayed ignition of 1. Manifold pressure is too 1. Contact local propane gas burner(s) low company 2. Burner orifice(s) is 2. Clean burner or
Streszczenie treści zawartej na stronie nr. 20
! WARNING WARNING ICON G 001 If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. POSSIBLE OBSERVED PROBLEM CAUSE REMEDY 1. Heater burning vapors Heater produces un- 1. Ventilate room. Stop us- from paint, hair spray, wanted odors
