Streszczenie treści zawartej na stronie nr. 1
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION . . . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 2
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor. • Do not locate th
Streszczenie treści zawartej na stronie nr. 3
UTOPIAN PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA LOCK™ HARDWARE • ALLEN SET SCREW DOWNROD & BALL 1 1 ⁄4-20 x ⁄4" ASSEMBLY 3mm (PRE-INSTALLED) ALLEN WRENCH FAN PREPARATION CAUTION: Before trimming wires or installing the downrod, pull the wires on the bottom of the fan to assu
Streszczenie treści zawartej na stronie nr. 4
UTOPIAN CEILING HARDWARE ADDITIONAL HARDWARE 1 2 /4″ x 8-32 ROUNDED HEAD SCREW (2) CROSSBAR WIRE NUT (4) 1″ x 8-32 ROUNDED MOUNTING FLAT WASHER (2) HEAD SCREW (2) BRACKET GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit breaker to place your Casablanca fan, an approved ceiling fixture or fuse box), lower the old fixture and d
Streszczenie treści zawartej na stronie nr. 5
UTOPIAN CANOPY INSTALLATION Step 2. Thread the wires from the ceiling through the opening in the canopy. Attach the canopy to CROSSBAR MOUNTING the crossbar mounting bracket with three of the BRACKET INSTALLED 1 8-32 x 2 /4″ long canopy screws and canopy lock washers. Using the screwdriver, tighten the screw firmly by hand only. CANOPY Note: On sloped ceilings, align the canopy opening toward the top or room peak. CANOPY LOCK WASHERS CANOPY SCREWS HANGING THE FAN Step 3. To hang the fan body in
Streszczenie treści zawartej na stronie nr. 6
UTOPIAN CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires CANOPY HATCH are clear of the canopy opening. Step 6. Install canopy hatch with the last LOCK canopy screw and lock washer. To do this, WASHER tilt the fan body away from the hatch CANOPY opening. SCREW TILT THE Using the screwdriver, tighten the screws FAN TO firmly by hand only, INSTALL LAST Step 7. Str
Streszczenie treści zawartej na stronie nr. 7
UTOPIAN BLADE INSTALLATION Step 9. Attach each blade to a blade holder securing it with the four blade screws provided. Using the screwdriver, tighten securely by hand only. BLADE BLADE SCREW (4 PER BLADE) BLADE HOLDER REMOVE SHIPPING BLOCKS Step 10. On the motor remove the five SHIPPING shipping blocks by unscrewing the screws. BLOCKS Set these screws aside for installing the blades in Step 11. Discard the five shipping blocks. BLADE/BLADE HOLDER INSTALLATION Step 11. Using the five screws rem
Streszczenie treści zawartej na stronie nr. 8
UTOPIAN REMOVE SWITCH HOUSING CAP SCREWS Step 12. Remove the two screws of the switch housing cap. Set the cap and screws aside for use in Step 15. INSTALL SWITCH HOUSING Step 13. Install 2 of the 3 switch housing screws onto the fan adapter plate, leaving 1 ⁄8" threads visible. Feed the wire connec- 2 SWITCH tor from the fan through the center of the HOUSING switch housing. SCREWS Align the 2 screws on the adapter plate with the keyhole slots of the switch housing. Raise the switch housing,
Streszczenie treści zawartej na stronie nr. 9
WHITE BLACK 3-SPEED OPERATION Pull-chain switches on the fan control the fan and lights. FAN & SPEED Using the fan control pull-chain switch: Fan off at start. REVERSE CONTROL First pull: fan ON, low speed PULL CHAIN PULL CHAIN SWITCH Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Using the optional light pull-chain switch: Light off at start. First pull: light ON Second pull: light OFF Direction of blade rotation is controlled by the reverse pull OPTIONAL LIGHT chain o
Streszczenie treści zawartej na stronie nr. 10
Product SPecificationS ™ ® Model name: Utopian Motor: 172mm x 20mm Direct Drive Model number: 77xxD Blade Span With: 50" Blade Pitch: 16° dimensions: A = 10.7" no. of Blades: 5 B = 12.22" t echnology: 3-Speed C = 3" D = 11.2" Airflow: 6,152 cfm E = 5.6" electricity use: 80 watts Airflow Efficiency: 76 cfm/watt Weight: 25 lbs.
