Streszczenie treści zawartej na stronie nr. 1
Important Safety Notice
Use, Care and Installation Guide
Read and save these instructions
Read all Instructions before Installing and operating this appliance
Important Safety Notice
d. Use an extinguisher ONLY if:
AK8000AS, AK8100S, AK8200S
MODEL:
1. You know you have a Class ABC extinguisher, and you already know how
to operate it.
READ AND SAVE THESE INSTRUCTIONS
2. The fire is small and contained in the area where it started.
3. The fire department is being calle
Streszczenie treści zawartej na stronie nr. 2
INSTALLATION MOUNT HEIGHTS Minimum mount height between range top to hood bottom should be no less than 24". Maximum mount height should be no higher than 32". It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire haz- ard; while hoods mounted too high will be hard to reach and will loose its performance Min 24"-Max 32" and efficiency. If available, also refer range manufacturer's height clearance requirements and recom- men
Streszczenie treści zawartej na stronie nr. 3
26-19/32” 27-9/16” 11-13/16” 10-11/16” INSTALLATION INSTALLATION DUCTING SPECIFICATIONS Twister (AK8000AS) WARNING FIRE HAZARD 5-15/16” NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling,attics or garages. All exhaust must be ducted to the outside. Use Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape. Some Ducting Options: side wall cap 4-3/32” side wall cap w/ gravity damper w/ gr
Streszczenie treści zawartej na stronie nr. 4
INSTALLATION INSTALLATION SPECIFICATIONS SPECIFICATIONS Tornado 1 unit (AK8100S) Tornado 2 unit (AK8200S) 33-7/16" 26-19/32” 16-3/16" 11-3/16” 10-5/16” 15-9/32” 27-9/16” 34-7/16” 9-27/32” 7-7/8” 2-3/8" 2-13/16" 27-9/16” 34-7/16 1-3/8” 2” 1/2" Elec. K.O. 6" 8" 1/2"Elec. K.O. 11-3/16” 16-3/16" 5-1/8” 10” C/L C/L 10-5/8” cut out dimension (cut out) 15-3/8” cut out dimension (cut out) 26-7/8” = cut out dimension 33-1/2” (cut-out) (cut out) = cutout dimension Page 4 Page 5
Streszczenie treści zawartej na stronie nr. 5
INSTALLATION CONTROLS&FEATURES INSTALLATION CONTROLS & FEATURES (AK8100S/AK8200S) Front View Mounting the Range Hood Ductwork 1. Determine and mark the mounting wood frame wood frame position of the range hood with a pencil. 2 Lights On/Off 1 Speed Selection 2. Cut out the opening where the range hood will be installed. 3. Cut out wall or ceiling area for clearance of ductwork. Install ductwork prior to range hood. 4. Determine location for the power Controls supply cable. After drilling access
Streszczenie treści zawartej na stronie nr. 6
MAINTENANCE MAINTENANCE CLEANING (AK8100S, AK8200S) CLEANING (AK8000AS) Models AK8100S and AK8200S hoods are designed with a self cleaning feature. The AK8000AS metal mesh filter fitted by the factory is intended to The centrifigal blower system automatically liquefies cooking residue accumulated filter out residue and grease from cooking. It need not be replaced in its internal housing and deposits the residue in the residue cups. Nevertheless, on a regular basis but is required to be kept cl
Streszczenie treści zawartej na stronie nr. 7
MAINTENANCE LIGHTS ReplacingLightBulbs CAUTION: Lightbulbbecomesextremelyhotwhenturnedon. DO NOT touchbulbuntilswitchedoffandcooled.Touchinghot bulbscouldcauseseriousburns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approx. the diameter of the bulb and turn. Replacement bulbs are available at specialty lighting stores. Purchase type GU-10 120V 35W halogen
