Streszczenie treści zawartej na stronie nr. 1
Find and replace list
Find Examples to Replace With
Wxxxx W1736
21˚ Framing Nailer 18 Gauge Stapler Kit
Nailer Stapler
MODEL W1781
21˚ FRAMING NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9572BL Printed in China
Streszczenie treści zawartej na stronie nr. 2
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ��������������������������������������������������������������� � �������� �����������������������������������������������������
Streszczenie treści zawartej na stronie nr. 3
Model W1781 21˚ Framing Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accide
Streszczenie treści zawartej na stronie nr. 4
Model W1781 21˚ Framing Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckties,
Streszczenie treści zawartej na stronie nr. 5
Model W1781 21˚ Framing Nailer Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work puncturing your hand or fingers. without stretching. However, an overly long air hose in the work 2. COMBUSTIBLE GASES: Never area may be a tripping
Streszczenie treści zawartej na stronie nr. 6
Model W1781 21˚ Framing Nailer INTRODUCTION Woodstock Technical Tool Data Support Nail Type .......................... Roundhead Nail Angle .................................. 21° This tool has been specially designed Nail Diameter ...........................0.113" to provide many years of trouble-free 1 Nail Length .............................2"–3 ⁄2" service. Close attention to detail, Magazine Capacity ...................75 Nails ruggedly built parts and a rigid quality 1 Air Inlet ......
Streszczenie treści zawartej na stronie nr. 7
Model W1781 21˚ Framing Nailer Compressed Air System The Model W1781 is designed to be operated at 80-110 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfactory result
Streszczenie treści zawartej na stronie nr. 8
Model W1781 21˚ Framing Nailer SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1781. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
Streszczenie treści zawartej na stronie nr. 9
Model W1781 21˚ Framing Nailer — If you find that the safety Safety Nose Mechanism nose mechanism is not working A safety mechanism on the nose of properly, check the lubrication of the nailer protects against accidental its sliding components. firing. When the trigger is pressed, the nailer will not fire until the safety nose — If the nailer fires when the trigger mechanism is depressed. is pulled, without the safety nose mechanism being depressed, then Before you use your nailer for the
Streszczenie treści zawartej na stronie nr. 10
Model W1781 21˚ Framing Nailer OPERATIONS 4. Slide the nails all the way down to Loading the nose of the nailer. When replacing nails in your Model W1781, follow these guidelines: 5. With one hand on the magazine handle for control, release the Type: .............................. Round Head magazine catch and slowly allow the Angle: ....................................... 21° magazine to press against the nails. Diameter: ............................... 0.113" 1 Length: .................
Streszczenie treści zawartej na stronie nr. 11
Model W1781 21˚ Framing Nailer 3. Depress the safety nose mechanism Adjusting Depth against your workpiece. A depth adjustment knob is attached to 4. Before pulling the trigger, make sure the nose for setting the nail depth. your free hand and other body parts are positioned out of the way of a To adjust the depth, do these steps: potential path of a nail in case of deflection. 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Deflection is caused when grain irregularities, knots or foreign obje
Streszczenie treści zawartej na stronie nr. 12
Model W1781 21˚ Framing Nailer Clearing Jammed Nails Replacing Pistons and O-Rings A jammed nail must be cleared before using the nailer again. Under heavy use, a piston or piston shaft may wear out. Replacement is quick and To clear a jammed nail from the dis- easy. Contact your authorized Shop Fox charge area, do these steps: dealer to obtain the Piston Repair Kit (part number X1781001). 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull the magazine handle all the way back until it
Streszczenie treści zawartej na stronie nr. 13
Model W1781 21˚ Framing Nailer 6. Open the nose cover as if to clear a 10. Insert the new piston in the cylinder. jammed nail. Make sure that the grooves on the piston shaft line up with those on the 7. Watch the discharge area and push guide at the bottom of the cylinder. the top of the piston with your The new piston should easily slide finger. You will see the piston shaft into the cylinder. DO NOT force the slide down the discharge area. piston into the cylinder! If the piston is not
Streszczenie treści zawartej na stronie nr. 14
Model W1781 21˚ Framing Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the nailer. Always be sure included with your new Shop Fox nailer that the nailer is dry before using it to help maintain its useful life. Place two again. to six drops of oil in the nailer air inlet (as shown in Figure 8) before every use, Do not allow dust, chips, sand, etc. or after 2 hours of continuous use. into the air conne
Streszczenie treści zawartej na stronie nr. 15
Model W1781 21˚ Framing Nailer PARTS BREAKDOWN �� �� � �� �� �� �� �� �� � �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � �� � � � � � � � -13-
Streszczenie treści zawartej na stronie nr. 16
Model W1781 21˚ Framing Nailer PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 X1781001 PISTON �REPAIR �KIT 50 XPSB03M CAP �SCREW � M5-.8 � X � 8 2 XPAW06M HEX �WRENCH � 6MM 51 X1781051 SAFETY � YOKE 3 XPAW05M HEX �WRENCH � 5MM 52 X1781052 COMPRESSION �SPRING 4 XPAW04M HEX �WRENCH � 4MM 53 X1781053 SAFETY � GUIDE 5 XPAW03M HEX �WRENCH � 3MM 54 XPRP02M ROLL � PIN� 3� X �16 6 X1781006 CARRYING �CASE 55 X1781055 SAFETY � SPACER 7 X1781007 AIR � PLUG � DUST � CAP 56 X1781056 TRIGGER
Streszczenie treści zawartej na stronie nr. 17
Model W1781 21˚ Framing Nailer Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at trig- 1. O-rings in trigger valve 1. O-rings must be replaced ger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Reseal and tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring. and hose 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking 1. Damaged seal. 1. Replace damaged
Streszczenie treści zawartej na stronie nr. 18
� � � � � � � �� � � �� � � � � � � � � � � � � � � ��� � � � � � � � � � � � � � �� � � � �� � � � � � � � �� � � �� � � � � � � � � �� � � ��� � � � �� � �� � �� � � � �� � �� � � � � � � �� � � � �� � � � � � � � � � ��� � � �� � � � � � � � � �� � � �� �� � � � � � �� � �� �� � � � �� � � � �� � � �� � � � �� � �� � � � � �� � �� � � � �� � � � �� � � �� � � � � � � � � �� � � � � �� � � � �� � � � � � � � �� � � � � �� � � �� � � � � � �� � � �� � � � �� � � �� � � � � �� � � ��� � � �� � �
Streszczenie treści zawartej na stronie nr. 19
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Streszczenie treści zawartej na stronie nr. 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
