Instrukcja obsługi Vision Fitness E4100

Streszczenie treści zawartej na stronie nr. 1

E4100
ASSEMBLY INSTRUCTIONS
To avoid possible damage to this Fitness Cycle,
please follow these assembly instructions.
Carefully remove all its parts from the box,
lay them out and review the parts list.
If any parts are missing, please call 1-800-335-4348, Ext 12
Before proceeding, find your Fitness Cycle’s serial number,
located on the underside of main frame, and enter here:
______________________________
Refer to this number when calling for service.
A41.2
IT ALL STARTS WITH A VISION

Streszczenie treści zawartej na stronie nr. 2

E4100 Parts Diagram

Streszczenie treści zawartej na stronie nr. 3

E4100 Parts VISION FITNESS E4100 Parts Description Part # Description Count Dimensions Front Wheel Parts #60 Front Foot Wheel Axle 1 #61 Front Transport Wheels 2 #182 Outside Wheel Washers 2 #183 Wheel Attachment Nuts 2 Arm Assembly Parts #116 Right Arm 1 #115 Left Arm 1 #74 Plastic Arm Cam Cover 2 #105 Inside Cam Pulley 2 #106 Outside Cam Pulley 2 #169 Pulley Washer 4 Flat #107 Cam Pulley Spring 2 #183 Cam Pulley Locknuts 2 Frame Parts #62 Rear Foot Assembly 1 #167 Rear Foot Attach Bolts 4 20mm

Streszczenie treści zawartej na stronie nr. 4

E4100 Assembly NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. Step 1 • Rear Foot 1:Secure the Rear Foot Assembly (62) to the Frame by using the four Rear Foot Attachment Bolts (167). Step 2 • Seat and Seat Post 1: Slide the Seat Post (65) into the frame seat post receiver tube. The seat post numbers should be facing the right or seat pin side of the Fitness Cycle. NOTE: Both nuts in the Seat Clamp

Streszczenie treści zawartej na stronie nr. 5

E4100 Assembly Step 5 • Connect Magnet Shift Cable 1: Turn the Tension Knob to position 8. Reach inside the opening of the Console Mast (70) and connect the Upper Magnet Shift Cable (179) to the rectangular red cable-slide on the end of the Lower Magnet Shift Cable (143), as shown in the accompanying illustrations. 2:While holding the metal separating tab (Figure 5), turn the Tension Knob to Level 1 and then pull the tab out and discard. 3:Press the Console Mast Plug (78) into the opening o

Streszczenie treści zawartej na stronie nr. 6

E4100 Assembly 6: Slip the Front Transport Wheel (61) onto the right side of the Front Foot Wheel Axle (60). Secure this wheel with the Outside Wheel Washer (182) and the Wheel Attach Nut (183). This nut should be tightened until the wheel has no side-to-side play, but it can still be easily rotated with your fingers. 7:Tighten the Cam Pulley Locknut (183). NOTE: This nut must be tightened all the way down or the Pulleys may loosen. When the Locknut is properly adjusted, the Outside Cam Pull

Streszczenie treści zawartej na stronie nr. 7

E4100 Final Assembly Step 7 • Pedals 1: Identify the left and right Pedals (91). Grease the Pedal threads, thread each Pedal into the correct left and right crank arms and tighten. NOTE: It is very important to FULLY TIGHTEN each pedal using a long wrench. Failure to do so will result in loosening and NOISE. Step 8 • Install Batteries and Test Operation 1:Remove the battery compartment lid on the back of the Console (95) and install the Batteries. Two AA-cell batteries are required. 2:The C

Streszczenie treści zawartej na stronie nr. 8

E4100 CAM PULLEY WHEEL W/SPRING INSTRUCTIONS (SERIAL #1198-CURRENT) CAM ARM SILVER INSIDE CAM WASHER PULLEY WHEEL OUTSIDE CAM PULLEY WHEEL SILVER COMPLETE SIDE VIEW WASHER CAM ARM INSIDE CAM OUTSIDE CAM NUT PULLEY WHEEL PULLEY WHEEL NUT SPRING BLACK WASHER SILVER SILVER SPRING BLACK WASHER WASHER WASHER

Streszczenie treści zawartej na stronie nr. 9

621-D East Lake Street P.O. Box 280 Lake Mills, WI 53551 (920) 648-4090