Instrukcja obsługi Stiga SNOW RISE 8218-2220-70

Streszczenie treści zawartej na stronie nr. 1

STIGA
DUO LINE
Snow Rise
BRUKSANVISNING SV.... 5
KÄYTTÖOHJEET FI ... 12
BRUGSANVISNING DA . 19
BRUKSANVISNING NO. 26
GEBRAUCHSANWEISUNG DE .. 33
INSTRUCTIONS FOR USE EN.. 40
MODE D’EMPLOI FR... 47
ISTRUZIONI PER L´USO IT.... 54
INSTRUKCJA OBS£UGI PL ... 61
»HC“P”K÷»fl œOÀ‹«Œ¬¿“EÀfl RU.. 69
NÁVOD K POU®ITÍ CS... 78
HASZNÁLATI UTASÍTÁS HU . 85
NAVODILA ZA UPORABO SL.... 92
8218-2220-70

Streszczenie treści zawartej na stronie nr. 2

1 13 2 4 6 7 5 9 8 12 10 11 16 13 14 15 3 2 B A C 2

Streszczenie treści zawartej na stronie nr. 3

4 5 F D G E 6 7 H H T V I U A B 8 9 3

Streszczenie treści zawartej na stronie nr. 4

EN ENGLISH 2.2 PREPARATIONS 1 SYMBOLS • Check the area to be cleared and remove any loose or foreign objects. The following symbols appear on the machine. They are • Disengage all controls before starting the engine. there to remind you of the care and attention required in use. This is what the symbols mean: • Never use the snow thrower unless properly dressed. Warning. Wear footwear that improves your grip on a slippery surface. • Warning – Petrol is highly inflammable. a. Always store

Streszczenie treści zawartej na stronie nr. 5

EN ENGLISH out of its place of storage. In this case ensure the door to the storage place is open. Exhaust fumes are toxic. 3 ASSEMBLY • Never drive across a slope. Move from the top down, and Note: Instructions to the left and right sides start from the from the bottom to the top. Be careful when changing driving position behind the snow thrower. direction on a slope. Avoid steep slopes. 3.1 CONTENTS - OUTER PACKING • Never operate the machine with insufficient protection or The packing c

Streszczenie treści zawartej na stronie nr. 6

EN ENGLISH 5. Tighten the screw (V) until the gear lever remains in the 4.8 OIL DRAINING PLUG (14) gear positions in the panel plate. For draining the old engine oil when changing the oil. 6. Set down the machine on its wheels. 4.9 SPARK PLUG PROTECTION (1) 3.7 CHECKING THE CONTROL WIRES The protection is easily removable by hand. The spark plug The control wires might need adjusting before using the is located under the protection. snow thrower for the first time. 4.10 GEAR LEVER (4) See ADJ

Streszczenie treści zawartej na stronie nr. 7

EN ENGLISH 3. Turn the choke (3) to position . Note: A warm engine 5 USING THE SNOW THROWER does not need the choke. 4. Pull on the starter cord until you feel resistance. Start the engine with a sharp pull. 5.1 GENERAL 5. When the engine starts, reset the choke until it is fully Never start the engine until all the above measures under open. ASSEMBLY have been carried out. Never use the snow thrower without first reading 5.5 STOPPING and understanding the instructions and all the 1. Re

Streszczenie treści zawartej na stronie nr. 8

EN ENGLISH 5.8 AFTER USE 6.5 TYRE PRESSURE 1. Check for loose or damaged parts. If required, change The air pressure should be equal in both tires for best damaged parts. performance. Be sure to keep caps on valves to prevent entry of debris into the valve stem when tires are filled. 2. Tighten loose screws and nuts. Recommended air pressure: 1.5 bar. 3. Brush all the snow from the machine. 4. Move all the controls backwards and forwards a few 6.6 LUBRICATION times. No service must be carri

Streszczenie treści zawartej na stronie nr. 9

EN ENGLISH 8. Reassemble the parts in the reverse order. NOTE! Only Auger does not Foreign matter Clean. genuine STIGA belts are to be used. rotate. blocking. 9. Adjust the control wire according to the instructions Shear pin broken. Replace the broken below. pin. 7.5 REPLACING THE DRIVE BELT Auger drive belt Adjust the belt and The drive drive belt (J) is shown in fig. 10. slipping. wire. 1. Dismantle the auger belt as described above. Auger drive belt Replace the belt. 2. When all parts a

Streszczenie treści zawartej na stronie nr. 10

EN ENGLISH 4. Remove the object that has fastened in the auger. 10 PURCHASE TERMS 5. Align the holes in the shaft and auger. 6. Remove the broken bolt parts. A full warranty is issued against manufacturing and material 7. Assemble a new original shear bolt. defects. The user must carefully follow the instructions given in the enclosed documentation. Exceptions: 8 STORAGE The warranty does not cover damage due to: - Neglect by the user to acquaint themselves with Never store the snow thrower

Streszczenie treści zawartej na stronie nr. 11

www.stiga.com GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS