Streszczenie treści zawartej na stronie nr. 1
ATTACHMENT
OPERATOR’S
MANUAL
Snow/Dozer
Blade & Hitch
Snow Plow/Dozer Blade
Mfg. No. Description
1691520 42” Snow Plow/Dozer Blade
Hitch
Mfg. No. Description
1692039 Hitch (for Landlord / 1700 / 2700 Series
& Broadmoor / 1600 / 2600 Series)
1692624 Hitch (for Regent / 500 / 2500 Series)
1715046-02
Rev 10/97
TP 100-2122-02-AT-SMA
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Recommended Accessories...................................................................................................................................1 Safety Rules.............................................................................................................................................................2 Components.................................................................................................................................................
Streszczenie treści zawartej na stronie nr. 4
Safety Rules Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The tri- angle in the text signifies important cautions or warnings which must be followed. WARNING For operation on slopes greater than 15% (8.5°), weight box, tire chains, and wheel weights are rec- ommended. Never operate on slopes greater than 30% (16.7°) General • Do not ru
Streszczenie treści zawartej na stronie nr. 5
Components F A B C H I G D M E L K J P L O N Figure 1. Mfg. No. 1691520 42” Snow Plow/Dozer Blade Components A. Blade Assembly I. Hex Capscrew, 1/2-13 x 1 (2) B. I.D. Plate J. Shoe Assembly (2) C. Hex Nut, 5/16-18 (4) K. Plain Washer, 3/8 (4) D. Eyebolt (2) L. Lockwasher, 3/8 (10) E. Tension Spring (2) M. Hex Head Capscrew, 3/8-16 x 3/4 (4) F. Pivot Frame Assembly N. Wear Plate G. Hex Lock Nut, 1/2-13 (2) O. Hex Nut, 3/8-16 H. Spacer (2) P. Carriage Bolt, 3/8-16 x 1 3
Streszczenie treści zawartej na stronie nr. 6
Components Broadmoor/LT/1600/2600, & Landlord/GT/1700/2700 Series Parts Manual Lift Rod Lift Rod Assembly Electric Lift Rod Push Bar Assembly Spring Assist & Chain Assembly Figure 2. Mfg. No. 1692039 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) M. Lockwasher, 5/16 B. Setscrew, 5/16 x 1/2 (Qty. 2) N. Full Hex Nut, 5/16-18 C. Rod Guide Assembly O. Hitch Pin D. Spring P. Plain Washer, 5/16 (Qty. 2) E. Lift Rod, (Manual or Electric Lift) Q. Chain F. Clip, Spring (Qty. 3) R. Spring G. K
Streszczenie treści zawartej na stronie nr. 7
Components Regent/500/2500 Series Parts Lift Rod Assembly I J Push Bar Assembly L K M Spring Assist & Chain Assembly N Figure 3A. Mfg. No. 1692624 Push Bar & Lift Rod Components A. Set Collar (Qty. 2) H. Push Bar Assembly B. Setscrew, 5/16 x 2 (Qty. 2) I. Hitch Pin C. Rod Guide Assembly J. Plain Washer 5/16 D. Spring K. Safety Clip E. Lift Rod L. Chain F. Spring Clip (Qty. 3) M. Spring G. Clevis Pin, 3/8 (Qty. 2) N. Pivot Pin 5
Streszczenie treści zawartej na stronie nr. 8
Components Regent/500/2500 Series Parts F C B C D D E M A L J K Q P I N O G F H Q G Figure 3B. Mfg. No. 1692624 Hitch Assembly A. Hitch Assy. J. Capscrew, 3/8-16 x 2 B. Rear Support Assy. K. Spacer, 25/64 x 5/8 x 17/64 C. Washers (Qty. 2) L. Spacer, 13/32 x 1 x 13/16 D. Hairpin Clip (Qty. 2) M. Nut, Whizlock, 3/8-16 E. Pin N. Lockwasher, 1/2 F. Spring Clip (Qty. 4) O. Hex Nut, 1/2-13 G. Clevis Pin, 3/8 (Qty. 2) P. Capscrew, 1/2-13 x 1-1/4 H. Rod Q. Upstop (Qty. 2) I. Spring Assist Bracket 6
Streszczenie treści zawartej na stronie nr. 9
Assembly All Models 1. Place the blade on a flat surface. 2. Regent/500/2500 & Broadmoor/LT/1600/2600 Series: See Figure 4. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B). Do not install second bar stop. Landlord/GT/1700/2700 Series: Do not install bar stops. Figure 4. Bar Stop A. Bar Stop B. Taptite Screw, 5/16-18 x 1 3. See Figure 5. Insert threaded end of eyebolt (A) thru lug on blade, and screw on 5/16 nut (B) just far enough so that it is flush with the end of the
Streszczenie treści zawartej na stronie nr. 10
Assembly NOTE: On single cylinder tractors, clevis pin (B, Figure 6) must be installed to bracket before mount- ing bracket on tractor frame. NOTE: Spring-assist bracket (A, Figure 6) does not need to be installed on units with electric lift. Broadmoor/LT/1600/2600 Series & Landlord/GT/1700/2700 Series Only: 7. See Figure 6. Install the spring-assist bracket (A) to tractor frame (bracket is mounted underneath frame). Secure with capscrew (from top), lock- washer, and nut. Place clevis pin (B)
Streszczenie treści zawartej na stronie nr. 11
Assembly Regent/500/2500 Series Only: 1. Increase front tire pressure to 20 psi (138 kPa) to compensate for added weight of the hitch, plus bar and blade. Be sure both tires have equal pressure. D 2. From the front of tractor, slide the hitch under the tractor so that the hitch bar is positioned at the front of the unit. E 3. See Figure 8. Turn the wheels fully left and lift the front hitch bar (A) up onto the tractor brackets (D). Make sure it is fully seated into the tractor brack- ets. Insta
Streszczenie treści zawartej na stronie nr. 12
Installation Broadmoor/LT/1600/2600 Series & Landlord/GT/1700/2700 Series 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. See Figure 10. Position the push bar hitch (A) into the tractor frame brackets (B). Secure push bar with pin (C) and safety clip (D). Figure 10. A. Push Bar Hitch C. Hitch Pin B. Frame Bracket D. Safety Clip Regent/500/2500 Series Only: C 1. Drive the tractor over the push bar until the
Streszczenie treści zawartej na stronie nr. 13
Installation All Models 4. See Figure 12. Raise the push bar and attach the spring (A) to the push bar bracket and the open end link of the 4-link spring assist chain. Figure 12. A. Spring 5. See Figure 13. Insert front of push bar (A) into pivot frame (B) on rear of blade. Then install king pin (C) down thru front holes in hitch and pivot frame. Secure king pin with spring clip (D). 6. See Figure 13. Using the king pin as a pivot, swiv- el the dozer blade to the desired position (angled left
Streszczenie treści zawartej na stronie nr. 14
Installation Viewed from Right Side of Tractor Figure 15. Electric Lift Bracket Figure 14. A. Lift Arm E. Front Attachment A. Rod Guide B. Clevis Pin Lift Rod B. Push Bar C. Safety Clip F. Clevis Pin C. Spring Clip D. Lift Lever G. Spring Clip Extension Assy. H. Rear Attachment Lift Rod (Optional) NOTE: Two lift rods are packaged with the Broadmoor/LT/1600/2600 & Landlord/GT/1700/2700 hitch assembly. Use the correct lift rod for manual or electric lift as shown in Figure 2. C B 7. Assemble lift
Streszczenie treści zawartej na stronie nr. 15
Removal 1. Lower the blade. 5. Remove the latch rod and spring clip securing push bar to tractor frame brackets, or clevis pins 2. Remove blade and lift rod from push bar. and spring clips securing push bar to hitch rail 3. Raise push bar and unhook the spring from the extensions. Remove push bar. chain. Remove the chain from the frame bracket. 6. Reinstall all pins (king pin, pivot pin, hitch pin) and Reinstall safety clip to clevis pin. secure with spring clip or safety clip for storage. 4. D
Streszczenie treści zawartej na stronie nr. 16
Adjustments Lift Rod See Figure 17. For initial setting, place front set collar (A) one inch from rod guide with blade fully lowered. Place rear set collar (B) against spring (C). Tighten the setscrews in the two set collars.To adjust, perform the following: 1. Fully raise the blade by pulling back on the tractor lift lever. Measure distance between scraper bar and ground. If it measures approximately six inch- es, it is properly adjusted. If not, proceed to step 2. 2. Lower the blade. Loosen t
Streszczenie treści zawartej na stronie nr. 17
Adjustments Spring Tension See Figure 19. This snow plow/dozer blade is spring loaded so that when the blade strikes a solid object, the springs will allow the blade to release as shown, rather than cause damage. The blade will go back to its original position after object is cleared. Figure 19. Dozer Blade “Released” See Figure 20. To adjust spring tension hold rear nut (B) and loosen front nut (E). Tighten rear nut (B) to increase spring tension, or loosen to decrease ten- sion. For initial
Streszczenie treści zawartej na stronie nr. 18
0 1 2 3 4 1/2 1/2 1/2 1/2 1/4 3/4 1/4 3/4 1/4 3/4 1/4 3/4 Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer No Hardware Lockwasher Marks Grade Carriage Bolt SAE Grade 2 SAE Grade 5 SAE Grade 8 Hex Nut Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. Standard Hardware Sizing 8-32 19 2.1 30 3.4 41 4.6 When a washer or nut is identified as 1/2”, this is the
Streszczenie treści zawartej na stronie nr. 19
Streszczenie treści zawartej na stronie nr. 20
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 1997 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.
