Streszczenie treści zawartej na stronie nr. 1
1
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLATION AND
OPERATION INSTRUCTIONS
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.
GD82NT-PA
NATURAL GAS
GD82PT-PA
PROPANE
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
SAFETY INFORMATION
!
WARNING
If the information in these instructions are
not followed exactly, a fire or explosion may
result causing prope
Streszczenie treści zawartej na stronie nr. 2
2 TABLE of CONTENTS Log Shipping Bracket PG2-5 INTRODUCTION Decorative Brick Panel Installation Warranty Log Placement Fireplace Dimensions Glowing Embers Installation Overview AFK / WI FACE KIT Installation General Instructions General Information 21-22 SERVICING / REPLACEMENTS Care of Glass Glass / Door Replacement 6-11 VENTING Blower Replacement Vent lengths Burner and Valve Replacement Venting Specifi cations Spark Module Battery Replacement TM
Streszczenie treści zawartej na stronie nr. 3
3 ® ® ® ® The following materials and workmanship in your new NAPOLEON® gas fireplace are warranted against defects for as long as you own the fireplace. This covers: combustion chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, gold plated parts against tarnishing, porcelainized enameled components and aluminum extrusion trims. Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves, thermal switch, switches, wiring, remote controls,
Streszczenie treści zawartej na stronie nr. 4
4 FIREPLACE DIMENSIONS 58" FIGURE 1 46" 3 17 /4" 5 37 /8" 4" DIA. 7" DIA. 1 22 /8" 21" 5" 7 13 /8" 2" 7 /8" 7 8 /8" 14" 24" GAS INLET 28" 28" INSTALLATION OVERVIEW FIGURE 2 W415-0665 / B / 02.11.08
Streszczenie treści zawartej na stronie nr. 5
5 This fireplace is only for use with the type of gas indicated on the GENERAL INSTRUCTIONS rating plate. This fireplace is not convertible for use with other gases, unless a certified kit is used. This gas fireplace should be installed and serviced by a qualified Expansion / contraction noises during heating up and cooling installer to conform with local codes. Installation practices vary down cycles are normal and are to be expected. Change in flame from region to region and it is impo
Streszczenie treści zawartej na stronie nr. 6
6 VENTING For optimum performance, it is recommended that horizontal runs VENT LENGTHS have a minimum 1/4” rise per foot when using Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, or American Metal For safe and proper operation of the fireplace follow the venting Amerivent rigid vent components and a minimum of 1” rise per instruction exactly. Deviation from the minimum vertical vent length can create foot when using Wolf Steel flexible vent components. When venting, the horizontal run
Streszczenie treści zawartej na stronie nr. 7
7 DEFINITIONS ELBOW VENT LENGTH VALUES for the following symbols used in the venting calculations feet inches and examples are: 1° 0.03 0.5 > - greater than 15° 0.45 6.0 > - equal to or greater than 30° 0.9 11.0 < - less than 45° 1.35 16.0 < - equal to or less than 90°* 2.7 32.0 H - total of both horizontal vent lengths (H ) and offsets T R (H ) in feet O * the fi rst 90° offset has a zero value and is shown in the H - combined horizontal vent lengths in feet R formula as -90°
Streszczenie treści zawartej na stronie nr. 8
8 HORIZONTAL TERMINATION V = V = 6 ft when (H ) > (V ) 1 T T T H = 3 ft 1 Simple venting confi guration (only one 90° elbow) H = 5 ft 2 H = H + H = 3 + 5 = 8 ft R 1 2 H = .03 (two 90° elbows - 90°) = .03(180° - 90°) = 2.7 FIGURE 7 O ft H = H + H = 8 + 2.7 = 10.7 ft T R O See graph to determine the required verti- H + V = 10.7 + 6 =16.7 T T cal rise V for the required horizontal run T Formula 1: H < 4.2 V H . T T T 4.2 V = 4.2 x 6 = 25.2 ft T 10.7 < 25.2 Formula 2: H + V < 24.7
Streszczenie treści zawartej na stronie nr. 9
9 VERTICAL TERMINATION when (H ) < (V ) Example 4: T T FIGURE 10 FIGURE 11 V 90° 3 90° H V 2 2 H 1 90° V 1 90° See graph to determine the required vertical rise V for the T required horizontal run H . T REQUIRED VERTICAL RISE IN FEET V = 5 ft 1 V V = 6 ft T 2 V = 10 ft 3 V = V + V + V = 5 + 6 + 10 = 21 ft T 1 2 3 H = 8 ft 1 H = 2.5 ft 2 H = H + H = 8 + 2.5 = 10.5 ft R 1 2 H = .03 (four 90° elbows - 90°) HORIZONTAL VENT RUN PLUS OFFSET IN FEET H O T = .03 (90 + 90 + 90 + 90 - 90) = 8.
Streszczenie treści zawartej na stronie nr. 10
10 VERTICAL TERMINATION when (H ) > (V ) T T FIGURE 12 90° 90° V 3 H 2 V V 1 2 H 1 90° 90° FIGURE 13 Example 5: V = 2 ft 1 V = 1 ft 2 Simple venting confi gurations V = 1.5 ft 3 See graph to determine the required vertical rise V for the T V = V + V + V = 2 + 1 + 1.5 = 4.5 ft T 1 2 3 required horizontal run H . T H = 6 ft 1 H = 2 ft 2 H = H + H = 6 + 2 = 8 ft R 1 2 MAXIMUM H = .03(four 90° elbows - 90°) O VERTICAL = .03(90 + 90 + 90 + 90 - 90) = 8.1 ft RISE IN H = H + H = 8 + 8.1 = 16
Streszczenie treści zawartej na stronie nr. 11
11 MINIMUM AIR TERMINAL LOCATION CLEARANCES FIGURE 14 GD-301 W415-0665 / B / 02.11.08
Streszczenie treści zawartej na stronie nr. 12
12 INSTALLATION WALL AND CEILING PROTECTION HORIZONTAL VENT SECTIONS: A minimum clearance of 2” all around the vent pipe on all horizontal runs to combustibles is required. Use firestop spacer W010-1799 (supplied). VERTICAL VENT SECTIONS: A minimum of 1” all around the vent pipe on all vertical runs to combustibles is required except for clearances in fireplace enclosures. Use firestop spacer W500-0096 (not supplied). HORIZONTAL INSTALLATION VERTICAL INSTALLATION This application occurs when
Streszczenie treści zawartej na stronie nr. 13
13 USING FLEXIBLE VENT COMPONENTS For safe and proper operation of the fireplace, follow the venting FIGURE 19 instructions exactly. ! WARNING ELBOW All inner exhaust and outer intake vent pipe joists may be sealed Do not allow the inside vent pipe to using either red RTV high temp silicone sealant or black high bunch up on horizontal or vertical runs temp Mill Pac with the exception of the fireplace exhaust flue and elbows. Keep it pulled tight. A 1 collar which must be sealed using Mill
Streszczenie treści zawartej na stronie nr. 14
14 7. Aligning the seams of the terminal and air terminal connector, FIREPLACE VENT CONNECTION place the terminal over the FIGURE 22c air terminal connector 1. Install the 4” diameter flexible vent pipe to the fireplace. making sure the liner goes Secure with 3 screws into the hole in the terminal. and flat washers. Seal Secure with the three screws the joint and screw 2” AIR INLET FIGURE 23 provided. holes using the high BASE 8. Apply a heavy bead of temperature sealant weatherpr
Streszczenie treści zawartej na stronie nr. 15
15 7. Aligning the seams of the terminal and air terminal connector, 4. When flexing any gas line, support the gas valve so that the place the terminal over the air terminal connector making sure lines are not bent or kinked. the liner goes into the hole in the terminal. Secure with the three 5. Check for gas leaks by brushing on a soap and water screws provided. Figure 22c solution. 8. Apply a heavy bead of weather-proof caulking 2” above the Do not use open flame. flashing. NOTE: Maintain
Streszczenie treści zawartej na stronie nr. 16
16 1" MIN 44" 1 22 /2" 1" MIN FIGURE 30a-b 10" 29" MIN ! WARNING Do not build into this area - it must be left clear to provide adequate clearance for the vent in this 14” wide area centered along the front of the fireplace. No combustibles FIGURE 31 are allowed. 3 1/2” MAXIMUM 72” 14” MINIMUM MINIMUM ENCLOSURE HEIGHT 1 1/2” MAXIMUM 22 1/2” 58 1/4” 29” GAS INLET 2” W415-0665 / B / 02.11.08 8 7/8” 29" 1 62 /8"
Streszczenie treści zawartej na stronie nr. 17
17 HORIZONTAL VENT SECTIONS: A minimum clearance of 2” all around MINIMUM ENCLOSURE CLEARANCES the vent pipe on all horizontal runs to combustibles is required. Use fi restop spacer W010-1799 (supplied). Minimum clearance to combustible construction from fi replace VERTICAL VENT SECTIONS: A minimum of 1” all around the vent pipe and vent surfaces: on all vertical runs to combustibles is required except for clearances in Combustible framing: fi replace enclosures. Use fi restop spacer W500
Streszczenie treści zawartej na stronie nr. 18
18 MINIMUM MANTEL AND ENCLOSURE CLEARANCES Combustible mantel clearance can vary according to the mantel depth. Use the graph to help evaluate the clearance needed. FIGURE 34 COMBUSTIBLE NON-COMBUSTIBLE FIGURES 33 COMBUSTIBLE BRICK 0” IF NON- 8” MANTEL COMBUSTIBLE NON-COMBUSTIBLE FINISHING IS 6” 2” 2” USED SUCH AS 8” 4” BRICK AND STONE 2” 14” TOP OF 26” 12” FIREPLACE 10” 8” 12 1/4” INSULATION SLEEVE TOP OF FIREPLACE 2” OPENING 72” NON- COMBUSTIBLE 14 56” MINIMUM 13 PLUS RISE* M H 12 A E
Streszczenie treści zawartej na stronie nr. 19
19 FINISHING DOOR REMOVAL LOG SHIPPING BRACKET Before the glass door can be removed, the optional front must be FIGURE 38 removed. The glass door is secured to the top front edge of the fi rebox with two latches. Pull the handles of the latches forward, then lift the hooks out from the slots in the door frame to release the top of the door. Next, pivot forward until the top edge of the door clears the front of the fi replace. Next gripping the sides of the door lift the door out from the re
Streszczenie treści zawartej na stronie nr. 20
20 LOG PLACEMENT NOTE: Decorative brick panels must be installed before the logs. See installation instructions supplied with the panel kit. TM ® PHAZER logs, exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. 4. Place log #4 with the charred FIGURE 39 a-f branch facing inward. Position 4 the pin in log #4 into the hole 1 on the right of log #2. 1. Place the rear log #1 onto the locating studs along the back edge of
