Instrukcja obsługi Merco Savory POP-2/4

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION
&
PARTS AND SERVICE MANUAL
POP-2/4
POP-UP TOASTER
The POP-2/4 Pop-Up Toaster is designed to
allow the operator to toast a wide vaariety of
bread products. The wide mouth opening (1”)
will accommodate varioues thicknesses of
bread, from thin sliced to Texas toast.
Each of the two toasting slots can hold one or
two slices of bread and the self-centering toast
guides assure each slice, regardless of thick-
ness, will be perfectly toasted, time and time
again. All controls are located

Streszczenie treści zawartej na stronie nr. 2

TABLE OF CONTENTS OPERATING INSTRUCTIONS------------------------------------------------------------------- 2 CLEANING INSTRUCTIONS--------------------------------------------------------------------- 2 INSTALLATION--------------------------------------------------------------------------------------- 3 SPECIFICATIONS----------------------------------------------------------------------------------- 3 WARRANTY---------------------------------------------------------------------------------

Streszczenie treści zawartej na stronie nr. 3

INSTALLATION Install the POP-2/4 in the most convenient location for ease of cleaning, maintenance, and general operation. Avoid installing in locations with drafts, close proximity to grease or vapor-producing appliances, or other high ambient heat equipment. Allow approximately 1” clearance on sides and back of unit for proper air circulation. Allow sufficient overhead clearance for proper operation of this unit. WARNING: This toaster must be plugged into the proper voltage which is specified

Streszczenie treści zawartej na stronie nr. 4

SEQUENCE OF OPERATIONS On the POP2/4 toaster, the sequence of operations is separate but identical for both left and right toasting slots. Power is permanently supplied to the power switch. Depressing the toast arm closes the power switch which supplies voltage to the control board. The control board energizes an electro magnet which holds the toast arm in a down position. The control board also supplies power to the heating elements. Adjusting the Light/Dark knob will change the amount of time

Streszczenie treści zawartej na stronie nr. 5

REMOVAL, INSTALLATION AND ADJUSTMENTS CAUTION: UNPLUG UNIT AND ALLOW TO COOL BEFORE ATTEMPTING ANY SERVICE PROCEDURES IN THIS MANUAL A. CASE COVER / CONTROL PANEL 1. Carefully place toaster upside down on a non-abrasive surface 2 Remove crumb tray. 3. Pry our rubber foot plugs adn use 1/3” nut driver to remove legs. 4. Push panel sides outward to gain clearance and slide out floor panel. 5. Push panel sides outward and lift out toaster chassis. 6. Unscrew both toast level handles and remove. 7.

Streszczenie treści zawartej na stronie nr. 6

C. P.C. BOARD 1. Remove case cover and control panel. (Section A) 2. Remove knob from front of control panel. NOTE: Thecontrol knob on the front panel consists of two parts the knob and the knob cap. The cap must be snapped off before removing the knob. Use a span ner wrench to loosen the knob and pull off the shaft. 3. Remove wire connections from the p.c. board. 4. Remove the 4 mounting nuts and remove the p.c. board. 5. When installing the new p.c. board make sure the sensing probe is inserte

Streszczenie treści zawartej na stronie nr. 7

WARNING (FOR MODELS MANUFACTURED BEFORE 9/1/90) WHEN ATTACHING WIRE CONNECTIONS< MAKE SURE CARGLAS SLEEVING IS FULLY INSERTED THROUGH OPENINGS AND COMPLETELY COVER TERMINAL ENDS. FAILURE TO DO SO WILL CAUSE ELECTRICAL SHORTING. G. Center Heater Card Assembly 1. Remove case cover. (Section A) 2. Remove 4 machine metal screws securing upper chassis. 3. Straghten twist tabs on upper chassis. 4. Disconnect both return springs at front of unit. 5. Remove both snap rings on upper chassis. 6. Slip o

Streszczenie treści zawartej na stronie nr. 8

Figure 5 Figure 6 8