Instrukcja obsługi Land Pride 4210

Streszczenie treści zawartej na stronie nr. 1

CVT And Cover Kit
Assembly Instructions
Treker 4210/4410 ST Series Manual No. 700-520M
Further Assistance
Before You Start
Your dealer wants you to be satisfied with your new CVT
When you see this symbol, the subsequent
And Cover Kit. If for any reason you do not understand
instructions and warnings are serious - follow
any part of this manual or are not satisfied with the
!
without exception. Your life and the lives of
service received, the following actions are suggested:
others depend on it!

Streszczenie treści zawartej na stronie nr. 2

Land Pride Assembly Instructions 2. Loosen hose clamp (#1B). Remove 1/4" Phillips Left Side Panel Detachment head self-tapping drive screws (#4), intake air hose The fuse box on the left side panel can interfere with (#9) and snorkel (#8). removing and assembling the CVT enclosure. It is simpler to detach the side panel from the frame than to detach the 3. Remove twelve 1/4" x 3/4" Phillips head screws (#2) fuse box. and outer enclosure (#6). Refer to Figure 1: 1. Remove five 1/4" hex flange lock

Streszczenie treści zawartej na stronie nr. 3

Land Pride Assembly Instructions 3. Remove CVT pulleys (#15 & #16) and CVT belt Removal of Pulleys & Inner Enclosure (#14). The following removed components will not be reused in assembly of the new CVT drive. 4. Remove CVT spacer (#1), shims (#19) and 3/16" x 1/4" x 2 1/2" key (#3) from engine drive shaft. Refer to Figure 3: 5. Remove 3/16" sq. x 3" long key (#2) from trans-axle 1. Remove 3/8" x 3 1/2" hex bolt (#7), lock washer (#9) driven shaft. and CVT adapter (#17) from CVT drive pulley (#1

Streszczenie treści zawartej na stronie nr. 4

Land Pride Assembly Instructions CVT Inner Enclosure Installation NOTE: A thin layer of silicon can be added to the Refer to Figure 4: gasket to hold it against the engine block and in 1. Loosen engine mounting hardware. alignment with mounting holes. NOTE: Clutch alignment tool (P/N 790-001A) may 4. Install gasket (#15) over engine drive shaft. Make be purchased from your nearest Land Pride Dealer. certain gasket holes are in alignment with mounting holes on engine block. 2. Use clutch alignmen

Streszczenie treści zawartej na stronie nr. 5

Land Pride Assembly Instructions and secure with twelve 1/4"-20 x 3/4" screws (#4). Do Assembly of CVT Pulley and Belt not tighten until all screws are installed. Tighten each Refer to Figure 4: screw to 5.6 ft-lbs. of torque. IMPORTANT: Pulley flanges will bend and nick easily 2. Install drain cap (#6) over drain nozzle and secure if handled roughly. Always handle pulleys gently to with 1" spring clamp (#3). prevent damage. 3. Install CVT diverter outlet (#8) to outer enclosure with two 3/16” po

Streszczenie treści zawartej na stronie nr. 6

Kit No. 700-519A Treker CVT/Cover Kit Qty. Part No. Part Description 1 700-112A CVT SHIM KIT TREKER / ATR 1 700-503S ASSEMBLY, CVT INNER COVER 1 700-520M CVT/COVER UPDATE MANUAL 1 710-097D KEY 3/16" x 3" 2 800-219C RIVET POP 3/16" .251"-.375" LF 1 800-235C SPRING CLAMP 1" OD HOSE 1 800-259C CLAMP WORM DRIVE #36SS (1.81-2.75) 1 800-350C KEY .187" x .247" x 2.25" LG 12 801-180C TTHMS 1/4"-20 x 3/4" 2 801-199C SCR SELF TAP #10 x 3/4" 4 801-215C HSFHCS 5/16"-24 x 1 1/4", BLK 1 802-329C HHCS 1/2"-20