Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
PLATINUM MARCY
Safety Notice
HOME GYM
Hardware Pack
PM-3000
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
PM-3000
Retain This
Manual for
Reference
08-20-08
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST…………………………………………………………………………………..17
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person a
Streszczenie treści zawartej na stronie nr. 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Streszczenie treści zawartej na stronie nr. 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. 4
Streszczenie treści zawartej na stronie nr. 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. 5
Streszczenie treści zawartej na stronie nr. 7
HARDWARE PACK 6
Streszczenie treści zawartej na stronie nr. 8
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do NOT tighten the nuts and bolts until instructed to do so. B.) Slide two Rubber Bumpers (#32) onto the two Guide Rods (#8). Insert the two Guide Rods into the holes on the Rear Base Frame (#2). Secure each Guide Rod with one M10 x 1” A
Streszczenie treści zawartej na stronie nr. 9
DIAGRAM 1 8
Streszczenie treści zawartej na stronie nr. 10
STEP 2 (See Diagram 2) A.) Slide 14 Weight Plates (#20) onto the Guide Rods (#8). Make sure the deep grooves on the Plates all face down and to the same direction. Insert the Selector Rod (#10) into the center hole on the Plates. Slide the Selector Stem (#19) onto the Guide Rods. B.) Attach the Upper Frame (#4) onto the Guide Rods. Secure it with two M10 x 1” Allen Bolts (#54) and Ø ¾” Washers (#60). C.) Place the Upper Frame onto the Vertical Frame (#3). Secure it with two M10 x 4 ¾”
Streszczenie treści zawartej na stronie nr. 11
STEP 3 (See Diagram 3) A.) Attach the Front Press (#6) to the Upper Frame (#4). Align the holes. Insert the Front Press Axle (#35) through the holes. Secure it with one M10 x 5/8” Allen Bolt (#53), one Ø ¾” Lock Washer (#57), one Ø ¾” Washer on each end of the Axle. Do not over tighten the Bolts. Make sure the Front Press is able to swivel. Cover the two Bolts with two Ø 1 3/8” End Caps (#39). B.) Attach the Backrest Board (#18) to the Vertical Frame (#3). Secure it with two M8 x 3
Streszczenie treści zawartej na stronie nr. 12
STEP 4 (See Diagram 4) A.) Attach the Seat Support (#1) to the Vertical Frame (#3). Secure it with two M10 x 3 ¾” Carriage Bolts (#48), one 4 3/8” x 1 ¾” Bracket (#13), two Ø ¾” Washers (#60), and two M10 Aircraft Nuts (#62). B.) Attach the Leg Developer (#7) to the open bracket on Seat Support. Secure it with the Leg Developer Axle (#34), two M10 x 5/8” Allen Bolts (#53), and two Ø ¾” Washers (#60). Do not over tighten the Bolts. Make sure the Leg Developer is able to swivel. C.) Pla
Streszczenie treści zawartej na stronie nr. 13
CABLE LOOP DIAGRAM 12
Streszczenie treści zawartej na stronie nr. 14
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 149” Upper Cable (#21) to the front opening on the Upper Frame (#4). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#24) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#50), two Ø 7/8” x 5/8” Bushings (#36), and one M10 Aircraft Nut (#62). C.) Draw the Cable towards the back of the machine to another opening on the Upper Frame. Repeat Procedure B above to install a Pulley
Streszczenie treści zawartej na stronie nr. 15
DIAGRAM 5 14
Streszczenie treści zawartej na stronie nr. 16
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 123” Lower Cable (#22) to the opening on the bottom of the Leg Developer (#7). B.) Attach a Pulley (#24) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#50), two Ø 7/8” x 5/8” Bushings (#36), and one M10 Aircraft Nut (#62). C.) Draw the Cable underneath the Pulley towards the back of the machine to the opening on the Vertical Frame (#13). Install a Pulley with one M10 x 2 3/8” Allen Bolt (#51), two ∅ 7/8” x ½” Bu
Streszczenie treści zawartej na stronie nr. 17
DIAGRAM 6 16
Streszczenie treści zawartej na stronie nr. 18
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Seat Support 1 51 M10 x 2 3/8” Allen Bolt 3 2 Rear Base Frame 1 52 M10 x 1 ¾” Allen Bolt 2 3 Vertical Frame 1 53 M10 x 5/8” Allen Bolt 4 4 Upper Frame 1 54 M10 x 1” Allen Bolt 5 5 Main Base Frame 1 55 M8 x 3 ½” Allen Bolt 2 6 Front Press 1 56 M8 x 3 3/8” Allen Bolt 2 7 Leg Developer 1 57 Ø ¾” Lock Washer 2 8 Guide Rod 2 58 M8 x 5/8” Allen Bolt 2 9 Lat Bar 1 59 M6 x 5/8” Philips Screw 1 10 Selector Rod 1 60 Ø ¾” Washer 22 11 4 3/
Streszczenie treści zawartej na stronie nr. 19
WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Lat Pull 30 40 50 60 70 80 90 100 110 22 33 44 55 66 77 88 99 110 Low Pulley Front Press 20 34 48 62 76 90 104 118 132 Leg Developer 26 38 50 62 74 86 98 110 122 WEIGHT PLATE Station 10 11 12 13 14 120 130 140 150 160 Lat Pull Low Pulley 121 132 143 154 165 Front Press 146 160 174 188 202 Leg Developer 134 146 158 170 182 Note: Each plate weights 10 lbs.
Streszczenie treści zawartej na stronie nr. 20
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPE
