Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY MWM 900
Hardware Pack
HOME GYM
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
PREMIER
Retain This
Manual for
Reference
08-05-03
IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
i
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 PARTS LIST…………………………………………………………………………………..17 RESISTA
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
Streszczenie treści zawartej na stronie nr. 4
HARDWARE PACK 3
Streszczenie treści zawartej na stronie nr. 5
HARDWARE PACK 4
Streszczenie treści zawartej na stronie nr. 6
HARDWARE PACK 5
Streszczenie treści zawartej na stronie nr. 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Slide two Ø2 ½” Round Rubber Bumpers (#43) onto the Guide Rods (#7). Insert the two Guide Rods into the holes on the Rear Stabilizer (#8). Secure each Guide Rod with one M10 x 1” Allen Bolt (#72) and ∅ ¾” Washer (#77) from the bottom. B
Streszczenie treści zawartej na stronie nr. 8
DIAGRAM 1 7
Streszczenie treści zawartej na stronie nr. 9
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#37) onto the Guide Rods (#7). Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Use a L-shaped Pin (#31) to select the number of Weight Plates. Slide the Selector Stem (#36) onto the Guide Rods. B.) Attach the holes on the Upper Frame (#6) onto the Guide Rods. Place the Upper Frame onto the Vertical Frame (#2). C.) Secure the Upper Frame (#6) to the Guide Rods (#7) with two M10 x 1” Allen Bolt
Streszczenie treści zawartej na stronie nr. 10
STEP 3 (See Diagram 3) A.) Place the Seat (#55) onto the Seat Support (#10). Secure it with two M8 x 1 5/8” Allen Bolts (#69) and Ø 5/8” Washers (#78). B.) Insert the Seat Support into the opening on the Main Base Frame (#1). Use a Lock Knob (#32) to secure the Seat Support at desired height. C.) Attach two ∅1” x ½” Bushings (#34) to the Leg Developer (#9). Attach the Leg Developer to the bracket on the Main Base Frame. Secure it with one M12 x 3 1/8” Allen Bolt (#71), two Ø 1” Washe
Streszczenie treści zawartej na stronie nr. 11
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#3) to the Upper Frame (#6). Secure it with one Axle (#24), two Spacers (#79), and two M10 Aircraft Nuts (#81). Do not over tighten the Nuts. B.) Insert the axle on the Right Butterfly (#4) through the hole on the Front Press Base from the bottom. Slide a Lock Ring (#60) onto the axle. Align the holes and secure it with one M6 x 1 5/8” Hex Bolt (#61) and M6 Aircraft Nut (#73). Repeat the same step to install the Left Butterfly (#5
Streszczenie treści zawartej na stronie nr. 12
CABLE LOOP DIAGRAM 11
Streszczenie treści zawartej na stronie nr. 13
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 144” Upper Cable (#57) to the front opening on the Upper Frame (#6). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two Ø 7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81). C.) Draw the Cable towards the back of the machine to another opening on the Upper Frame. Repeat Step B above to install a Pulley. D.
Streszczenie treści zawartej na stronie nr. 14
DIAGRAM 5 13
Streszczenie treści zawartej na stronie nr. 15
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 108” Butterfly Cable (#58) to the hook on the Right Butterfly (#4). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B.) Attach a Pulley (#41) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#65), two ∅ ¾” Washers (#77), and one M10 Aircraft Nut (#81). C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#15). Install a Pulley
Streszczenie treści zawartej na stronie nr. 16
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 144” Lower Cable (#59) to the opening on the bottom of the Leg Developer (#9). B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two ∅ 7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81). C.) Draw the Cable underneath the Pulley towards the back of the machine through the opening on the bottom of the Main Base Frame (#1) to an open bracket. D.) Attach a Pulley to the bracket.
Streszczenie treści zawartej na stronie nr. 17
DIAGRAM 7 16
Streszczenie treści zawartej na stronie nr. 18
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Base Frame 1 51 2” x 1” End Cap 4 2 Vertical Beam 1 52 Ø 1” End Cap 3 3 Front Press Base 1 53 Front Press Handle 2 4 Right Butterfly 1 54 Foam Roll End Cap 4 5 Left Butterfly 1 55 Seat 1 6 Upper Frame 1 56 Backrest Board 1 7 Guide Rod 2 57 144” Upper Cable 1 8 Rear Stabilizer 1 58 108” Butterfly Cable 1 9 Leg Developer 1 59 144” Lower Cable 1 10 Seat Support 1 60 Lock Ring 2 11 Lat Bar 1 61 M6 x 1 5/8” Hex Bolt 2 12
Streszczenie treści zawartej na stronie nr. 19
18
Streszczenie treści zawartej na stronie nr. 20
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
