Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY SMITH MACHINE
Safety Notice
MXM-5
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MXM-5
Retain This
Manual for
Reference
09-01-05
OWNER'S
IMPEX
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK….......…..........................................………………………. 4 ASSEMBLY INSTRUCTIONS...........................................……………………. 8 EXPLODED DIAGRAM…………………………………………………………….. 23 PARTS LIST………..……………………………………………………………….. 25 WARRANT
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
Streszczenie treści zawartej na stronie nr. 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown. 3
Streszczenie treści zawartej na stronie nr. 5
HARDEWARE PACK 4
Streszczenie treści zawartej na stronie nr. 6
HARDEWARE PACK 5
Streszczenie treści zawartej na stronie nr. 7
HARDEWARE PACK 6
Streszczenie treści zawartej na stronie nr. 8
HARDEWARE PACK 7
Streszczenie treści zawartej na stronie nr. 9
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so. B.) Connect the Left & Right Base Frames (#17 & #18) by a Cross Brace (#20) in the mid- span. Secure each end of the Cross Brace with two M10 x 2 ½” Carriage Bolts (#92), one 4 3/8
Streszczenie treści zawartej na stronie nr. 10
DIAGRAM 1 9
Streszczenie treści zawartej na stronie nr. 11
STEP 2 (See Diagram 2) A.) Attach the Rear Vertical Beam (#23) onto the Cross Brace (#20). Attach the Weight Glide Post (#22) to the Rear Vertical Beam and Cross Brace. Align the holes and secure them with two M10 x 2 ¾” Carriage Bolts (#93), ∅ ¾” Washers (#82), and M10 Aircraft Nuts (#99). B.) Slide the Sliding Weight Post (#34) onto the Weight Glide Post (#22). C.) Place the Upper Frame (#21) onto the Rear Vertical Beam (#23), Weight Glide Post (#22), and Front Top Beam (#32). D
Streszczenie treści zawartej na stronie nr. 12
DIAGRAM2 11
Streszczenie treści zawartej na stronie nr. 13
STEP 3 (See Diagram 3) A.) Attach the Butterfly Base (#24) and Butterfly Pulley Bracket (#33) to the Rear Vertical Beam (#23). Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#92), ∅ ¾” Washers (#82), and M10 Aircraft Nuts (#99). B.) Insert the pivot on the Right Butterfly (#26) through the hole on the Butterfly Base. Secure it with one Lock Ring (#73), M6 x 1 ¼” Allen Screw (#100), and M6 Aircraft Nut (#101). C.) Push a Butterfly Arm Pad (#49) onto the Right Butter
Streszczenie treści zawartej na stronie nr. 14
STEP 4 (See Diagram 4) A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting Sleeve (#38) in between the two Safety Stop Frames (#37). Align the holes and insert the Weight Bar (#39) into the Safety Stop Frame from one end through the Weight Lifting Sleeve to the other Safety Stop Frame on the opposite end. Secure the Weight Bar to each Safety Stop Frame with a M8 x 3/8” Allen Bolt (#103). B.) Turn the safety hook on the Weight Lifting Sleeve to
Streszczenie treści zawartej na stronie nr. 15
CABLE LOOP DIAGRAM 14
Streszczenie treści zawartej na stronie nr. 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach a 124” Cable (#51) to the front opening on the Upper Frame (#21). Attach a Pulley (#74) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#87), two Ø 7/8” Bushings (#79), and one M10 Aircraft Nut (#99). Make sure the ball stopper of the Cable is underneath the Upper Frame. B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper Frame. Attach a Pulley to the opening. Secure it wit
Streszczenie treści zawartej na stronie nr. 17
DIAGRAM 5 16
Streszczenie treści zawartej na stronie nr. 18
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 79” Butterfly Cable (#52) to the clip on the Left Butterfly (#25). Draw the Cable to the left Butterfly Pulley Bracket (#33). B.) Attach a Pulley (#74) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#36). Install a Pulley to the Bracket. Let t
Streszczenie treści zawartej na stronie nr. 19
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one 124” Cable (#51) to the lower opening on the Rear Vertical Beam (#23). Attach a Pulley to the opening. Secure it with M10 x 2 3/8” Allen Bolt (#88), two Ø 1” Bushings (#78), and one M10 Aircraft Nut (#99). B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post (#22). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99)
Streszczenie treści zawartej na stronie nr. 20
STEP 8 (See Diagram 8) A.) Attach the Main Seat Support (#1) to the Front & Rear Stabilizers (#3 & #4). B.) Secure each end with two M10 x 3 1/8” Carriage Bolts (#94), one 4 ¾” Curve Bracket (#8), two ∅ ¾” Washers (#82), and two M10 Aircraft Nuts (#99). DIAGRAM 8 19
