Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
MWM 900
Table of Contents
HOME GYM
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 900
Retain This
Manual for
Reference
OWNER'S
MANUAL
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 2 IMPORTANT SAFETY PRECAUTIONS.........................................................……….. 3 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST………………………………………………………………………………….. 18 RESISTANCE CHAR
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY PRECAUTIONS This gym built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or use your gym. In particular, note the following safety precautions: 1. Keep children and pets away from the gym at all times. Do not leave children unattended in the same room with the gym. The gym is not a toy and therefore parents and guardians should be aware of the natural
Streszczenie treści zawartej na stronie nr. 4
HARDWARE PACK 4
Streszczenie treści zawartej na stronie nr. 5
5
Streszczenie treści zawartej na stronie nr. 6
6
Streszczenie treści zawartej na stronie nr. 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A) Slide two Ø2 ½” Round Rubber Bumpers (#43) onto the Guide Rods (#7). Insert the two Guide Rods into the holes on the Rear Stabilizer (#8). Secure each Guide Rod with one M10 x 1” Allen Bolt (#72) and ∅ ¾” Washer (#77) from the bottom. B) Attach t
Streszczenie treści zawartej na stronie nr. 8
DIARGRAM 1 8
Streszczenie treści zawartej na stronie nr. 9
STEP 2 (See Diagram 2) A) Slide 9 Weight Plates (#37) onto the Guide Rods (#7). Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Use a L-shaped Pin (#31) to select the number of Weight Plates. Slide the Selector Stem (#36) onto the Guide Rods. B) Attach the holes on the Upper Frame (#6) onto the Guide Rods. Place the Upper Frame onto the Vertical Frame (#2). C) Secure the Upper Frame (#6) to the Guide Rods (#7) with two M10 x 1” Allen Bolts (#72)
Streszczenie treści zawartej na stronie nr. 10
STEP 3 (See Diagram 3) A) Place the Seat (#55) onto the Seat Support (#10). Secure it with two M8 x 1 5/8” Allen Bolts (#69) and Ø 5/8” Washers (#78). B) Insert the Seat Support into the opening on the Main Base Frame (#1). Use a Lock Knob (#32) to secure the Seat Support at desired height. C) Attach two ∅ 1” x ½” Bushings (#34) to the Leg Developer (#9). Attach the Leg Developer to the bracket on the Main Base Frame. Secure it with one M12 x 3 1/8” Allen Bolt (#71), two Ø 1” Washer
Streszczenie treści zawartej na stronie nr. 11
STEP 4 (See Diagram 4) A) Attach the Front Press Base (#3) to the Upper Frame (#6). Secure it with one Axle (#24), two Spacers (#79), and two M10 Aircraft Nuts (#81). Do not over tighten the Nuts. B) Insert the axle on the Right Butterfly (#4) through the hole on the Front Press Base from the bottom. Slide a Lock Ring (#60) onto the axle. Align the holes and secure it with one M6 x 1 5/8” Hex Bolt (#61) and M6 Aircraft Nut (#73). Repeat the same step to install the Left Butterfly (#5).
Streszczenie treści zawartej na stronie nr. 12
CABLE LOOP DIAGRAM 12
Streszczenie treści zawartej na stronie nr. 13
STEP 5 (See Diagram 5 & Cable Loop Diagram) A) Attach the 144” Upper Cable (#57) to the front opening on the Upper Frame (#6). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two Ø 7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81). C.) Draw the Cable towards the back of the machine to another opening on the Upper Frame. Repeat Step B above to install a Pulley. B) Draw
Streszczenie treści zawartej na stronie nr. 14
DIAGRAM 5 14
Streszczenie treści zawartej na stronie nr. 15
STEP 6 (See Diagram 6 & Cable Loop Diagram A) Attach one end of the 108” Butterfly Cable (#58) to the hook on the Right Butterfly (#4). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B) Attach a Pulley (#41) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#65), two ∅ ¾” Washers (#77), and one M10 Aircraft Nut (#81). C) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#15). Install a Pulley as d
Streszczenie treści zawartej na stronie nr. 16
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 144” Lower Cable (#59) to the opening on the bottom of the Leg Developer (#9). B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two ∅ 7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81). C.) Draw the Cable underneath the Pulley towards the back of the machine through the opening on the bottom of the Main Base Frame (#1) to an open bracket. D.) Attach a Pulley to the bracket. Sec
Streszczenie treści zawartej na stronie nr. 17
DIAGRAM 7 17
Streszczenie treści zawartej na stronie nr. 18
PARTS LIST KEY NO DESCRIPTION QTY 53. Front Press Handle 2 54. Foam Roll End Cap 4 1. Main Base Frame 1 55. Seat 1 2. Vertical Beam 1 56. Backrest Board 1 3. Front Press Base 1 57. 144” Upper Cable 1 4. Right Butterfly 1 58. 108” Butterfly Cable 1 5. Left Butterfly 1 59. 144” Lower Cable 1 6. Upper Frame 1 60. Lock Ring 2 7. Guide Rod 2 61. M6 x 1 5/8” Hex Bolt 2 8. Rear Stabilizer
Streszczenie treści zawartej na stronie nr. 19
19
Streszczenie treści zawartej na stronie nr. 20
LIMITED WARRANTY Escalade warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the frame and one year on all other parts and components from the date of purchase. This warranty extends only to the original purchaser. Escalade’s obligation under this Warranty is limited to replacing damaged or faulty parts at Escalade’s option. All returns must be pre-authorised by Escalade. This warranty does no
