Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all
instructions carefully
before using this product
Table of Content
Safety Notice
Hardware Pack
MARCY
Assembly Instruction
MWB-345 BENCH
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MWB-345
Retain This
Manual for
Reference
02-25-05
OWNER'S
MANUAL
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENT BEFORE YOU BEGIN............................................................................................... 1 IMPORTANT SAFETY NOTICE................................................................................ 2 HARDWARE PACK………......................................................................................... 3 ASSEMBLY INSTRUCTIONS.................................................................................... 4 EXPLODED DIAGRAM................
Streszczenie treści zawartej na stronie nr. 3
PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the
Streszczenie treści zawartej na stronie nr. 4
3
Streszczenie treści zawartej na stronie nr. 5
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span. Secure them with two M10 x 2 3/8” Hex Bolts (#2), four ∅ ¾” Washers (#3), one Bracket (#7), and two M10 Aircraft Nuts (#4) on each end of the Cross Brace. B.) Insert the
Streszczenie treści zawartej na stronie nr. 6
STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52). Secure them with two M10 x ¾” Hex Bolts (#46), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15). Secure them with two M10 x 2 3/8” Bolts (#2), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4). C.) Connect one end of Diagonal Support (#43) to the Main Seat Su
Streszczenie treści zawartej na stronie nr. 7
STEP 3 (SEE DIAGRAM 3) A.) Attach the Leg Developer (#38) onto the bracket on the Front Stabilizer (#42). Secure it with an Allen Socket Axle (#44) and Allen Socket Screw (#45). B.) Insert two Foam Roll Tubes (#39) halfway through the hole on the Leg Developer. Push four Foam Rolls (#37) onto the Tube from both ends. Plug four Ø 1” Foam Roll End Caps (#36) onto each end of the Tubes. C.) Clip a Spring Clip (#34) onto the post on the Leg Developer. D.) Attach the Arm Curl Handle Supp
Streszczenie treści zawartej na stronie nr. 8
STEP 4 (SEE DIAGRAM 4) A.) Attach the hole-side of the Backrest Supports (#16) onto both ends of the Pivot on the Main Seat Support (#52). The other side rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#18) onto the Backrest Supports (#16). Secure it with four M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51). C.) Place the Seat (#19) onto the bracket on the Main Seat Support (#52). Align the holes and secure it with four M6 x 1 3/8” Hex Bolts (#50) an
Streszczenie treści zawartej na stronie nr. 9
STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable (#27) to the Pulley (#28). Place the Pulley in the open slot on the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two Pulley Bushings (#29), two ∅ ¾” Washers (#3), and one M10 Aircraft Nut (#4). B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom. Connect the Cable to the Holder with a Hook (#26). C.) Connect the Lat Bar (#25) to the Cable with a Hook (#26). When using the La
Streszczenie treści zawartej na stronie nr. 10
9
Streszczenie treści zawartej na stronie nr. 11
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Rear Upright Beam 2 2 M10 x 2 3/8” Hex Bolt 6 3 ∅ ¾” Washer 18 4 M10 Aircraft Nut 9 5 1 5/8” x 3 1/8” Square End Cap 6 6 1 ¼” Square End Cap 2 7 Bracket 2 8 Short Lock Pin 1 9 ∅ 1” Round End Cap 5 10 Backrest Adjustment Bar 1 11 Bar Catch Panel 2 12 ∅ ¾” Bar Catch End Cap 2 13 Right Bar Catch 1 14 Left Bar Catch 1 15 Cross Brace 1 16 Backrest Support 2 17 1” Square End Cap 2 18 Backrest Board 1 19 Seat 1 20 M8 x ¾” Hex Bol
Streszczenie treści zawartej na stronie nr. 12
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust
