Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
MARCY CORNER GYM
Hardware Identifier
CR 4
Assembly Instruction
Parts List
Resistance Chart
How to Use
Warranty
Ordering Parts
Model
MWB CR 4
Retain This
Manual for
Reference
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
6-18-01
www.impex-fitness.com
info@impex-
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 PARTS LIST…………………………………………………………….…………….21 RESISTANT CHART…………………
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
Streszczenie treści zawartej na stronie nr. 4
3
Streszczenie treści zawartej na stronie nr. 5
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each other. Attach the Rear Vertical Beam (#5) to the joint and align the holes. Secure the top hole with a M10 x 2 ¾” Carriage Bolt (#90), ∅3/4” Wash
Streszczenie treści zawartej na stronie nr. 6
STEP 2 (See Diagram 2) A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅3/4” Washers (#106), and two M10 Aircraft Nuts (#110). B.) Attach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M10 x 2 ½” Allen Bolt (#97), ∅ ¾” Washer (#106), and 4” x 2” Bracket (#39) into the upper hole. Secure the bottom hole with one M10 x 2 ¾” Carriage
Streszczenie treści zawartej na stronie nr. 7
6
Streszczenie treści zawartej na stronie nr. 8
STEP 3 (See Diagram 3) A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106) and two M10 Aircraft Nuts (#110). B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them with two M10 x 2 ¾” Carriage Bolts (#90), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110). DIAGRAM 3 7
Streszczenie treści zawartej na stronie nr. 9
STEP 4 (See Diagram 4) A.) Attach four ∅1” x ½” Bushings (#55) to the Leg Press Pivot Arm (#18). Attach the Pivot Arm to the bracket on the Right Base Frame (#1). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two ∅ 1” Washers (#105), and one M12 Aircraft Nut (#109). B.) Attach two ∅1”x1/2” Bushings (#55) to the tube on the Leg Press Frame (#19). Attach the Leg Press Frame (#19) to the top of the Pivot Arm (#18). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two ∅ 1”
Streszczenie treści zawartej na stronie nr. 10
STEP 5 (See Diagram 5) A.) Insert the Chromed Adjustment Tube (#20) into the Leg Press Frame (#19). Secure it with a Quick Release Pin (#62). B.) Attach the Foot Plate (#21) to the Chromed Tube (#20) and secure it with a L-Shaped Pin (#112). C.) Attach the Bench Press Frame (#11) to the pivot tube on the Right Base Frame (#1). Insert a M10 x 8 5/8” Axle (#82) through the holes. Secure it with two ∅ ¾” Washers (#106) and M10 Aircraft Nuts (#110) on both sides. Close the ends with t
Streszczenie treści zawartej na stronie nr. 11
STEP 6 (See Diagram 6) A.) Attach the Butterfly Support Frame (#8) to the front of the Right Vertical Beam (#3). Attach the Butterfly Pulley Support (#113) to the back of the Right Vertical Beam (#3). Secure them with two M10 x 3” Carriage Bolts (#89), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110). B.) Insert the axle on the Right Butterfly (#10) into the hole on the Butterfly Support Frame (#8) from the bottom up. Secure it with a ∅1 ½” Washer (#59) and M12 Aircraft Nut (#1
Streszczenie treści zawartej na stronie nr. 12
STEP 7 (See Diagram 7) A.) Attach the Leg Developer Frame (#15) to the Left Vertical Beam (#4). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106), and two M10 Aircraft Nuts (#110). B.) Attach the Leg Developer Frame (#15) to the Left Base Frame (#2). Secure it with a M10 x 2 ¾” Carriage Bolt (#90), ∅ ¾” Washer (#106), and M10 Aircraft Nut (#110). C.) Place a ∅1 ½” Ring (#114) onto the pivot axle on the Left Base Frame (#2). Th
Streszczenie treści zawartej na stronie nr. 13
STEP 8 (See Diagram 8) A.) Attach the Seat (#40) to the Leg Developer Frame (#15). Secure it with two ∅5/8” Washers (#107) and M8 x 2 ½” Allen Bolts (#101). B.) Attach both Left Handlebar (#32) and Right Handlebar (#33) to the Leg Developer Frame (#15) underneath the Seat (#40). Secure them with two M10 x 2 ¾” Carriage Bolts (#90), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110). C.) Attach two ∅1” x ½” Bushings (#55) to the Leg Developer (#23). Attach the Leg Developer to t
Streszczenie treści zawartej na stronie nr. 14
STEP 9 (See Diagram 9 & 15) A.) Attach a Pulley (#58) to the bracket on the Right Butterfly Arm (#10). Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾” Washers (#106), and one M10 Aircraft Nut (#110). Repeat to install another Pulley to the other side. B.) Attach one end of the 86” Butterfly Cable (#84) to the Right Butterfly Pulley Bracket (#29). Install a Pulley (#58) to the Bracket and secure it with a M10 x 1 ¾” Hex Head Bolt (#92), two ∅ ¾” Washers (#106), and a M10 A
Streszczenie treści zawartej na stronie nr. 15
STEP 10 (See Diagram 10 & 15) A.) Attach the Ball-end of the 132” Upper Cable (#85) to the Right Upper Frame (#6). Install a Pulley (#58). Push two Bushings (#56) into the holes from both sides. Secure it with one M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable towards the back of the machine along the top of the Right Upper Frame (#6). Install another Pulley (#58) using one M10 x 1 ¾” Hex Head Bolt (#92), two ∅ ¾” Washers (#106), and one M10 Aircraft
Streszczenie treści zawartej na stronie nr. 16
STEP 11 (See Diagram 11 & 15) A.) Attach one end of the 327 ½” Leg Press Cable (#83) to the bracket on the Leg Press Pivot Arm (#18). (See C View) Secure it with one M10 x 1” Allen Bolt (#99), two ∅ ¾” Washers (#106), and one M10 Aircraft Nut (#110). NOTE: Do not over tighten this bolt. Make sure the head of the cable can swivel on the bolt. B.) Draw the Cable to the Vertical Supports (#16). Install a Pulley (#58). Secure it with one M10 x 5” Allen Bolt (#96), two ∅ ¾” Washers
Streszczenie treści zawartej na stronie nr. 17
16
Streszczenie treści zawartej na stronie nr. 18
STEP 12 (See Diagram 12 & 15) A.) Attach the Ball-end of the 158” Ab Cable (#86) to the opening on the Left Vertical Beam (#4). Install a Pulley (#58). Push two Bushings (#56) from both sides of the Beam. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable over the Pulley downward and install another Pulley to a Double Floating Pulley Bracket (#30). Secure it with one M10 x 1 ¾” Hex Head Bolt (#92), two ∅ ¾” Washers (#106), and one M10 A
Streszczenie treści zawartej na stronie nr. 19
STEP 13 (See Diagram 13 & 15) A.) Attach the Ball-end of the 102” Leg Curl Cable (#87) to the opening on the Leg Developer (#23). Install a Pulley (#58) to the opening. Attach two Bushings (#56) to the holes on the Leg Developer. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Pull the Cable through the openings to the bracket on the Left Base Frame (#2). Install a Pulley. Secure it with a M10 x 1 ¾” Hex Head Bolt (#92), two ∅ ¾” Washers (#106), an
Streszczenie treści zawartej na stronie nr. 20
STEP 14 (See Diagram 14 & 15) A.) Tighten all the nuts and bolts previously installed. B.) Before putting the Weight Plates on, now move the machine to the corner of the room or place where you will use the machine. C.) Lift up the Selector Rod and install the Weight Plates. To install the plates, hold the plate at an angle and place between the two guide rods then drop it down. Make sure the grooves on the plastic covers all face up. See diagram below. It is strongly recommende
