Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
COMPETITOR BENCH
Hardware Identifier
CB-339
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB 339
Retain This
Manual for
Reference
05-31-02
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fi
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM.....................................................
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Streszczenie treści zawartej na stronie nr. 4
3
Streszczenie treści zawartej na stronie nr. 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left Upright Beam (#1) and Right Upright Beam (#2) by a Cross Brace (#3) in the mid-span. Align the holes and secure each end of the Cross Brace with one Bracket (#16), two M10 x 2 ½” Carriage Bolts (#28), two ∅ ¾” Washers (#33), and t
Streszczenie treści zawartej na stronie nr. 6
STEP 2 (See Diagram 2) A.) Attach the Main Stabilizer (#21) to the Cross Brace (#3). Secure it with a 4 3/8” x 1 ½” Bracket (#43), two M10 x 2 ½” Carriage Bolts (#28), ∅ ¾” Washers (#33), and M10 Aircraft Nuts (#38). B.) Attach the Front Support (#10) to the Main Stabilizer (#21). Secure it with one M10 x 2 3/8” Allen Bolt (#36) and ∅ ¾” Washer (#33). C.) Attach one end of Man Seat Support (#4) to the Main Stabilizer (#21). Secure it with two M10 x 2 ½” Carriage Bolts (#28), ∅ ¾” Was
Streszczenie treści zawartej na stronie nr. 7
STEP 3 (See Diagram 3) A.) Attach the hole-side of Backrest Supports (#9) to the pivot on the Main Seat Support (#4). Secure it with one M12 x 5 7/8” Hex Bolt (#13) and M12 Aircraft Nut (#37). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar. B.) Place the Backrest Board (#17) onto the Backrest Supports (#9). Secure it with four M6 x 1 3/8” Hex Bolts (#31) and ∅ ½” Washers (#35). C.) Place the Seat (#18) onto the Main Seat Support (#4). Secure it with
Streszczenie treści zawartej na stronie nr. 8
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#6) to the open bracket on the Front Support (#10). Secure it with one M10 x 3” Allen Bolt (#30), two ∅ ¾” Washers (#33), and one M10 Aircraft Nut (#38). B.) Insert the two Foam Tubes (#8) halfway through the holes on the Leg Developer. Push four Foam Rolls (#20) onto the Foam Tubes. C.) Attach the Bar Holder (#12) to the Leg Developer (#6). Secure it with a L-shaped Pin (#15). Remove the Bracket when using the Leg Developer.
Streszczenie treści zawartej na stronie nr. 9
8
Streszczenie treści zawartej na stronie nr. 10
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Upright Beam 1 2 Right Upright Beam 1 3 Cross Brace 1 4 Main Seat Support 1 5 Backrest Adjustment Bar 1 6 Leg Developer 1 7 Crutch 2 8 Foam Tube 2 9 Backrest Support 2 10 Front Support 1 11 Arm Curl Stand 1 12 Bar Holder 1 13 M12 x 5 7/8” Hex Bolt 1 14 Curl Bar 1 15 L-shaped Pin 1 16 Bracket 2 17 Backrest Board 1 18 Seat 1 19 Arm Curl Pad 1 20 Foam 4 21 Main Stabilizer 1 22 1 ¾” Square End Cap 6 23 1 ½” Square End Cap
Streszczenie treści zawartej na stronie nr. 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Custo
