Streszczenie treści zawartej na stronie nr. 1
R
BODEGA BAY WOOD INSERT
Advanced Combustion Technology (ACT)
OWNER’S MANUAL
Installation and Operation
Model:
BODBAY
Portland
Tested and
O-T L
Listed by Oregon USA
C US
OMNI-Test Laboratories, Inc.
This manual contains instructions for Installation, Operation & Maintenance.
Please read this entire manual before you install and use your new room heater. Failure to follow
instructions may result in property damage, bodily injury, or even death.
IMPORTANT SAFETY NOTES:
1) When installing your
Streszczenie treści zawartej na stronie nr. 2
R BODEGA BAY WOOD INSERT and Welcome to the Quadra-Fire Family! Hearth & Home Technologies welcomes you to our tradition craftsmanship. Each unit is meticulously fabricated and surfaces of excellence! In choosing a Quadra-Fire appliance, you have are hand-finished for lasting beauty and enjoyment. Our pledge our assurance of commitment to quality, durability, and perfor- to quality is completed as each model undergoes a quality control mance. inspection. From design, to fabrication, t
Streszczenie treści zawartej na stronie nr. 3
R BODEGA BAY WOOD INSERT Table of Contents OPERATION OVERVIEW SAFETY & OVERVIEW OF APPLIANCE Wood Selection & Storing ---------------------------------- 16 Location & Sample of Serial Number Label -----------2 Overfiring-------------------------------------------------------- 16 Dimensions -----------------------------------------------------4 Building A Fire ------------------------------------------------- 16 Minimum Clearances to Combustibles ------------------4 Operating Tips --------------
Streszczenie treści zawartej na stronie nr. 4
R BODEGA BAY WOOD INSERT DIMENSIONS TOP VIEW CLEARANCES TO COMBUSTIBLES 30-3/16" United States and Canada (767mm) 24-1/16" Maximum Mantel Depth - 10" (254mm) (611mm) Mantel C L Fascia or Trim B 11-3/4" (298mm) C A D Insert E 8-3/8" F (213mm) Hearth Extension SIDE VIEW USA CANADA A Sidewall to Stove 15" (381mm) 15" (381mm) B Mantel to Stove 2 6" (660mm) 23" (584mm) C Top Trim to Stove 20" (508mm) 20" (508mm) 21-9/16" D Side Trim to Stove 6" (152mm) 6" (152mm
Streszczenie treści zawartej na stronie nr. 5
R BODEGA BAY WOOD INSERT LISTINGS CHIMNEY HEIGHT/DRAFT (CONT’D) These installation instructions describe the installation and AVOID FIRE: To ensure that insulation or any other combustible operation of the Quadra-Fire Bodega Bay Wood Insert. This material does not contact the chimney, a chimney inside the house insert meets the U.S. Environmental Protection Agency’s 1990 must have at least 2 inches (51mm) of air space clearance around particulate emission standards. This product is lis
Streszczenie treści zawartej na stronie nr. 6
R BODEGA BAY WOOD INSERT GENERAL INSTALLATION PROCEDURE • DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. • Install liner, if required, for your chosen installation. • Attach metal warning plate to the back of the fireplace with screws or nails. • Set appliance on the hearth (See Hearth Requirements page 4 and Support Kit information on page 15.) • Complete the vent connection required for your installation type. • Relocate plate for Outside Air. (Required for Mobile Home
Streszczenie treści zawartej na stronie nr. 7
R BODEGA BAY WOOD INSERT OVALIZING ROUND STAINLESS STEEL CHIMNEY REqUIREMENTS LINERS A chimney must be the required height above the roof or other obstruction for safety and for proper draft oper- Ovalizing round stainless steel liners to acommodate ation. The requirement is that the chimney must be at the liner passing through the damper region of a fire- place is an allowable and acceptable practice. least 3 ft (91cm) higher than the highest point where it passes through the roof, and
Streszczenie treści zawartej na stronie nr. 8
R BODEGA BAY WOOD INSERT INSTALLATIONS INTO ZERO CLEARANCE FIREPLACES IN MOBILE HOMES (IN USA ONLY) 1. An outside air inlet must be provided for combustion and Spark Arestor Cap must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability Storm Collar to maintain a fire. Smoke spillage can also set off smoke alarms. Roof Flashing 2. Unit must be secured to the mobile home
Streszczenie treści zawartej na stronie nr. 9
R BODEGA BAY WOOD INSERT INSTALLATION OPTIONS Refer to: Clearances to Combustibles on page 4, Canadian Installation Requirements on page 11, Hearth Requirements on page 4 and Zero Clearance Adjustable Support Kit on page 15. MASONRY FIREPLACE USING DIRECT-CONNECT METHOD Masonry Chimney Flue Tile This product conforms with the UL Standard for Safety 1482 and ULC S628 (Canada) in all respects, and is approved to Full Listed Mantel Liner Option UL & ULC safety standards for installation an
Streszczenie treści zawartej na stronie nr. 10
R BODEGA BAY WOOD INSERT FACTORY BUILT ZERO CLEARANCE FIREPLACE (USA INSTALLATONS ONLY) The Quadra-Fire Bodega Bay ACT Wood Stove Insert is listed to UL 1482 Standard and approved for installation into listed factory built zero clearance fireplaces listed to UL 127 conforming to the following specifications and instructions: Mantel The original factory-built clearance fireplace chimney cap must be re-installed after installing the approved chim- ney liner meeting type H.T. requirements (2
Streszczenie treści zawartej na stronie nr. 11
R BODEGA BAY WOOD INSERT INSTALLATION IN CANADA MASONRY and HEAT-CIRCULATING (INSTALLATIONS INTO FACTORY-BUILT FIREPLACES ARE PROHIBITED IN CANADA) Whether installed in a masonry or heat-circulating fireplace, this fireplace insert must be installed with a continuous chim- ney liner of six inch (152mm) diameter extending from the fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirements of CAN/ULC-S635, Standard for Lining Systems for Existing Ma
Streszczenie treści zawartej na stronie nr. 12
Attach liner with 2 tabs R BODEGA BAY WOOD INSERT SECURING LINER TO CHIMNEY RING There are 2 options to secure the liner to the chimney ring: (See Figure 12A). Option One: If there is enough room on the top of the 2 pre-drilled holes on insert to work, hand bend the two tabs upward 90°. chimney ring under outer skin Secure the liner with the supplied hex head bolts 1/4- (access through firebox) 20-3/4. Option Two: Remove the manifold tubes, fiberboard baffle and ceramic blanket. From
Streszczenie treści zawartej na stronie nr. 13
R BODEGA BAY WOOD INSERT PANEL and GOLD or NICKEL TRIM SET STANDARD: 30-1/2” h x 44-5/8”w Screw side panels to top LARGE: 34”h x 50-1/2”w panel SP-BB3044-GD Panel & Trim Set, Std, Gold SP-BB3044-NL Panel & Trim Set, Std, Nickel SP-BB3450-GD Panel & Trim Set, Large, Gold SP-BB3450-NL Panel & Trim, Set, Large, Nickel Tab with screw hole to secure Included in Panel Kit: (2) side panels, left and right; (1) panel panel to insert top; (2) trim sides, left and right; (1) trim top (1) faste
Streszczenie treści zawartej na stronie nr. 14
BLOWER CORD LOCATION R BODEGA BAY WOOD INSERT FAN (BLOWER) REPLACEMENT BLOWER CORD LOCATION & BLOWER CONTROL BOX WITH SWITCH Included in Kit: Replacement Blower This insert comes standard with a blower, installed at the Tools Needed: 5-32 Wrench and Phillips Head Screwdriver. factory with blower cord on right side of insert (as you face 1. Remove bolts from both sides of the insert and slide the the unit). The blower cord can also be installed on the left lower cover towards you. See Fi
Streszczenie treści zawartej na stronie nr. 15
R BODEGA BAY WOOD INSERT ZERO CLEARANCE ADJUSTABLE TRIM SUPPORT, 2” to 10” Part No. 841-0990, size 9”d x 45”w and Part No. ADJSPT-12, size 12”d x 50”w Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides, Double-Sided Tape (already installed) Tools Needed: Phillips Head Screwdriver, Sheet Metal Shears, Measuring Tape, Gloves EXPLODED VIEW OF SCISSORS 1. The 10 screws on each set of scissors will already be loose when shipped. See Figure 15A. 2. Expand scissors to desired height.
Streszczenie treści zawartej na stronie nr. 16
R BODEGA BAY WOOD INSERT OPERATION WOOD SELECTION AND STORAGE Burn only dry seasoned wood. Dry, well-seasoned wood will not only minimize the chance of creosote formation but will give you the most efficient heat output. Even dry wood contains at least 15% moisture by weight and should be burned hot enough to keep the chimney hot enough to maintain particulate (smoke) burning. Burning unseasoned wood of any variety defeats the inserts’ efficiency. Dead wood lying on the forest floor should
Streszczenie treści zawartej na stronie nr. 17
R BODEGA BAY WOOD INSERT OPERATING TIPS For maximum operating efficiency with the lowest emissions, follow these operating procedures: 1. Regardless of desired heat output, when loading stove, burn your Quadra-Fire with both air controls wide open for a minimum of 5 to 15 minutes. 2. Regulate burn rate (heat output) by using the Primary Control (top rod). The Start-Up Air Control (bottom rod) is mainly for initial start-up and reloading. 3. Heat output settings: Follow burn rate instruction
Streszczenie treści zawartej na stronie nr. 18
R BODEGA BAY WOOD INSERT AIR qUALITY AND YOUR qUADRA-FIRE INSERT In recent years there has been an increasing concern about the quality of our air. Much of the blame for poor air quality has been placed on the burning of wood for home heating. In order to improve this situation we at Quadra-Fire have developed cleaner burning inserts that surpass the stringent requirements for emissions established by our governing agencies. Your Bodega Bay Wood Insert, like any other appliance, must be
Streszczenie treści zawartej na stronie nr. 19
R BODEGA BAY WOOD INSERT MAINTENANCE CARE AND CLEANING OF PLATED SURFACES IMPORTANT: You must clean all the fingerprints and oils from the plated surfaces before firing the insert for the first time. Use warm soapy water and a soft rag, glass cleaner and a paper towel, or vinegar and a paper towel to remove the oils. DO NOT use abrasive cleaners! If not cleaned properly prior to lighting the first fire, the oils can cause permanent stains. The plating will be cured upon firing of the inse
Streszczenie treści zawartej na stronie nr. 20
R BODEGA BAY WOOD INSERT BRICK REPLACEMENT INSTRUCTIONS PART 832-3500 The firebox of your insert is lined with high quality fire- 1 4 6 6 1 4 brick which has exceptional insulating properties. There is no need for a grate, simply build a fire on the firebox of your insert. 5 5 1. Be certain coals are completely cold. Remove all old brick and ash from unit and vacuum out firebox. 4 4 2. Remove new brick set from box and lay out to the diagram 4 4 5 4 4 as shown. 4 4 3. Lay bottom bricks i
