Instrukcja obsługi Harbor Freight Tools CENTRAL PNEUMATIC 46309

Streszczenie treści zawartej na stronie nr. 1

®
AIR BRAD NAILER
Model 46309
ASSEMBLY and OPERATING
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2001, 2004 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced
in any shape or form without the express written consent of Harbor Freight Tools.
For technical qu

Streszczenie treści zawartej na stronie nr. 2

Specifications Brad Size .039-.042” Shank (18 Gauge), 3/8” to 2” long Magazine Capacity 100 Operating PSI 55-95 PSI Air Inlet Size 1/4” NPT Male Safety Feature Full Sequential Safety Trip Mechanism Dimensions 9-3/4” L x 8-5/8” H x 2-1/4” W Accessories Two Hex Wrenches, Lubricating Oil Fasteners available from Harbor Freight Tools: SKU 43213 - 18 gauge brad nails, 1000 pieces. Save This Manual You will need the manual for the safety warnings and precautions, assembly instruc- tions, operating and

Streszczenie treści zawartej na stronie nr. 3

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI approved impact safety goggles. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating

Streszczenie treści zawartej na stronie nr. 4

panel fuse to break. If this happens, either use the compressor without an extension cord or find a larger amperage circuit to use. 19. Maintenance. The maintenance outlined in the maintenance section should be performed regularly. For your safety, this product should be serviced or repaired regularly only by a qualified technician. 20. Compressed air only. Never use combustible gas as a power source. 21. Do not load nails with the trigger or safety depressed. Unintentional firing may occur

Streszczenie treści zawartej na stronie nr. 5

Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. NOTE: Although a spare Drive Pin (46), Step Pin (45), Piston Head (44), O-ring (43), and assorted O-rings are included, these parts are for installation by a qualified technician only. Operation For best service, you should incorporate an oiler, regulator, and inline filter, as sho

Streszczenie treści zawartej na stronie nr. 6

Operation (continued) Air Inlet (38) FIGURE 1 Retaining Spring (58) Trigger (29) Safety Magazine (60) Loading Brad Nails ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. 1. Press the Retaining Spring (58) up and slide the Magazine (60) back. 2. Holding the nailer wit

Streszczenie treści zawartej na stronie nr. 7

Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (60) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (60) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. FIGURE 2 Clearing Jams 1. Disconnect tool from air hose, empty t

Streszczenie treści zawartej na stronie nr. 8

Anytime any maintenance or repairs are done, FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (60) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (60) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. Troubleshooting Guide Stop using the Brad Nailer immediately if any of the following probl

Streszczenie treści zawartej na stronie nr. 9

Parts List Pn artDt escriptioPn arDt escriptioPn ar Descriptio 1tE4 xhaus 2mT7 rigger Valve Ste 4w Scre 2wS5 cre 2gO8 -Rin 4I Cover I 3rW6 ashe 2eV9 alve Guid 4r Quick Release Leve 4yC7 ylinder Cap Assembl2eR0 eleasing Blad 5g Sprin 5rS8 eal Ai 2gE1 -rin 5r Driver Guide Cove 6gC9 ompression Sprin 2rT2 rigge 5e Driver Guid 7tG0 aske 3nS3 pring Pi 5w Scre 8gO1 -rin 3nS4 tep Pi 5n Spring Pi 9gO2 -rin 3eF5 ram 5g Sprin 1n 0H3 ead Valve Pisto 3nS6 pring Pi 5y Safet 1g 1O4 -Rin 3rS7 toppe 5w Scre 1r 2

Streszczenie treści zawartej na stronie nr. 10

Assembly Drawing Maintenance Warning! Always disconnect the tool from the air compressor and then empty the magazine of nails before attempting to inspect or perform maintenance to the Nailer. 1. Inspect all of the nuts and screws and make sure they are securely fastened. 2. Periodically lubricate the driving mechanism and magazine with a light oil. Wipe down with a clean cloth. Never use gasoline or flammable solvents to clean the tool. 3. Inspect your air compressor according to manufacture