Streszczenie treści zawartej na stronie nr. 1
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Otreap Or ’s Mlauna
Yard Vacuum/Chipper/Shredder with Vacuum/Hose
Model CSV 060
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA Form No. 769-08982
(June 21, 2013)
Streszczenie treści zawartej na stronie nr. 2
To The Owner 1 Thank You Thank you for purchasing a Chipper/Shredder Vacuum If applicable, the power testing information used to establish manufactured by Troy-Bilt. It was carefully engineered to the power rating of the engine equipped on this machine can be provide excellent performance when properly operated and found at www.opei.org or the engine manufacturer’s web site. maintained. If you have any problems or questions concerning the machine, Please read this entire manual prior to ope
Streszczenie treści zawartej na stronie nr. 3
Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - HEED ITS WARNING! CALIFORNIA PROPOSITION 65 WARNING: Engine Exhaust, some of its constituents, and certain
Streszczenie treści zawartej na stronie nr. 4
4. If the impeller strikes a foreign object or if your machine Safe Handling of Gasoline: should start making an unusual noise or vibration, To avoid personal injury or property damage use extreme care immediately shut the engine off. Allow the impeller to in handling gasoline. Gasoline is extremely flammable and the come to a complete stop. Disconnect the spark plug wire, vapors are explosive. Serious personal injury can occur when ground it against the engine and perform the following
Streszczenie treści zawartej na stronie nr. 5
Maintenance & Storage Do not modify engine 1. Never tamper with safety devices. Check their proper To avoid serious injury or death, do not modify engine in any operation regularly. way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper 2. Check bolts and screws for proper tightness at frequent with factory setting of engine governor. intervals to keep the machine in safe working condition. Also, visually inspect machine
Streszczenie treści zawartej na stronie nr. 6
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING— ROTATING BLADES Keep hands out of inlet and discharge openings while machine is running. There are rotating blades inside BYSTANDER
Streszczenie treści zawartej na stronie nr. 7
Assembly & Set-Up 3 Contents of Carton • One Chipper/Shredder Vacuum • One Operator’s Manual • One Engine Operator’s Manual • One Upper and Lower Handle • One Hose Assembly • One Safety Glasses • One Bag • One Bottle of Oil • One Hose Extension 2. Unfold the upper handle until it aligns with lower handle. Assembly Make sure the rope guide is on the right side of upper NOTE: This unit is shipped without gasoline or oil in the engine. handle. See Figure 3-2A. Fill up gasoline and oil as instruc
Streszczenie treści zawartej na stronie nr. 8
4. Loosen the wing nut that secures the rope guide to the 2. Pull spring loaded pin out on the base and align pin with right side of upper handle. the first hole (closest to the end of the tube) in the hose adapter. See Figure 3-4B. a. Slowly pull starter rope out of engine. 3. Release the pin to lock the hose in place. b. Slip the starter rope into the rope guide. See Figure 3-3. 4. Lay hose tubing in curved end of hose handle next to chipper chute and into hose cradle (if applicable). See
Streszczenie treści zawartej na stronie nr. 9
Bag Adjustments 1. Grasp bag handle with one hand and slide locking rod on Nozzle Height mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the The nozzle can be adjusted to any six positions, ranging from locking rod. See Figure 3-6. 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to chipper shredder conditions. 1. Depress nozzle height adjustment lever towards wheel. See Figure 3-7. 3 2 2 1 3 4 1 Figure
Streszczenie treści zawartej na stronie nr. 10
Controls and Features 4 Recoil Starter Bag Hose Handle Hose Assembly Hose Extension Chipper Chute Nozzle/Hose Vac Lever Nozzle Nozzle Height Adjustment Lever WARNING: The operation of any chipper shredder Hose Assembly can result in foreign objects being thrown into the Used as an alternative to the nozzle to vacuum yard waste such eyes, which can damage your eyes severely. Always as leaves or pine needles. wear the safety glasses provided with this unit or eye shields while operating or
Streszczenie treści zawartej na stronie nr. 11
Operation 5 5. Twist the two buttons on the back of the bag to unlock and Starting & Stopping Engine empty contents. See Figure 5-2. Hold bag handle and bag Refer to the Engine Operator’s manual packed with your chipper/ clip while emptying the contents. shredder vacuum for instructions on starting and stopping the engine. To Empty Bag 1. Unhook bag straps from the lower handle. 2. Unsnap bag clip from the top of lower handle. See Figure 5-1. 2 Buttons Inner Flap 4 Outer Flap Figure 5-2 6.
Streszczenie treści zawartej na stronie nr. 12
Using The Nozzle Vacuum Using The Hose Assembly Yard waste such as leaves and pine needles can be vacuumed 1. Place nozzle/hose vac lever in the bottom position on the up through the nozzle for shredding. After material has been nozzle to redirect vacuum to the hose assembly. See Figure shredded by the flail blades on the impeller assembly, it will be 5-4. discharged into catcher bag. Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e. branches, le
Streszczenie treści zawartej na stronie nr. 13
Maintenance & Adjustments 6 Equipment Care Maintenance • Clean the chipper/shredder vacuum thoroughly after each General Recommendations use. • Always observe safety rules when performing any • Wash bag periodically with water. Allow to dry thoroughly maintenance. in shade. • The warranty on this chipper/shredder vacuum does not • If the flail screen becomes clogged, remove and clean as cover items that have been subjected to operator abuse or instructed below. negligence. To receive full
Streszczenie treści zawartej na stronie nr. 14
Removing the Flail Screen If the discharge area becomes clogged, remove the flail screen and clean area as follows: 1. Stop the engine. Make certain the chipper/shredder vacuum has come to a complete stop. 2. Before unclogging the discharge chute, disconnect and ground the spark plug wire to retaining post. 3. Remove the vacuum bag from the unit as instructed in the OPERATION section to obtain access to flail screen. 4. Remove self tapping screw on right side of unit that attaches to the fl
Streszczenie treści zawartej na stronie nr. 15
Service 7 Blade Care Front Support Brace/ WARNING: Before performing any type of Lock Nut maintenance on the machine, wait for all parts to Bell Pivot Arm stop moving and disconnect the spark plug wire. Washer Assembly Failure to follow this instruction could result in personal injury or property damage. Thrust Washer NOTE: When tipping the unit, empty the oil and fuel tank and keep engine spark plug side up. Shoulder Wave Screw 1. Disconnect and ground the spark plug wire to retainin
Streszczenie treści zawartej na stronie nr. 16
7. Carefully tilt and support the unit up to provide access 10. The nuts on the flat head cap screws can be reached underneath to the nozzle mounting hardware and impeller. from underneath using a 1/2-inch socket, universal, and Remove the three shoulder bolts securing the black plastic extension. See Figure 7-6. lower flail housing to the lower housing. Refer to Figure 7-4. Impeller Nuts Figure 7-6 11. Replace or sharpen chipper blade. The blade can be Figure 7-4 sharpened with a file or on
Streszczenie treści zawartej na stronie nr. 17
Troubleshooting 8 Problem Cause Remedy Engine Fails to start 1. Throttle lever (if equipped) not in correct 1. Move throttle lever to FAST or START starting position. position. 2. Engine switch (if equipped) in OFF position. 2. Move engine switch to ON position. 3. Spark plug wire disconnected. 3. Connect wire to spark plug. 4. Choke not in CHOKE position (if equipped). 4. Move choke lever to CHOKE position. 5. Fuel tank empty or stale fuel. 5. Fill tank with clean, fresh gasoline. 6. Fuel shut
Streszczenie treści zawartej na stronie nr. 18
Replacement Parts 9 Component Part Number and Description BS-591868 Spark Plug (Briggs & Stratton) 951-14437 Spark Plug (MTD Engine) BS-491588S Air Filter Cartridge (Briggs & Stratton) BS-493537S† Pre-Cleaner (Briggs & Stratton) 951-10298 Air Cleaner Kit (MTD Engine) BS-799585 Fuel Cap (Briggs & Stratton) 951-14407 Fuel Cap Assembly (MTD Engine) BS-298090S† Fuel Filter (Briggs & Stratton) 951-10358A Fuel Filter (MTD Engine) 664-04029 Bag 981-0490 Chipper Blade 719-0329 Flail Blade (2 total) 634-
Streszczenie treści zawartej na stronie nr. 19
Notes 10 19
Streszczenie treści zawartej na stronie nr. 20
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by Troy-Bilt LLC with c. Routine maintenance items such as lubricants, filters, blade respect to new merchandise purchased and used in the United States sharpening, tune-ups, brake adjustments, clutch adjustments, and/or its territories and possessions, and by MTD Products Limited deck adjustments, and normal deterioration of the exterior finish with respect to new merchandise purchased and used in Canada and/ d
