Streszczenie treści zawartej na stronie nr. 1
L0542
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
www.fi sher-price.co.uk
Streszczenie treści zawartej na stronie nr. 2
Consumer Information IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach. • Please read these instructions before assembly and use of WARNING this product. • Adult assembly is required. Prevent serious injury or death from falls • Tool needed for assembly: Phillips screwdriver (not included). or sliding out: • Product features and decorations may vary from photographs. • The child should at all times
Streszczenie treści zawartej na stronie nr. 3
Assembled Parts 2 Frames Pad Seat Back Seat Bottom 2 Bases Footrest 2 Seat Bottom Tubes Food Tray Hinge Rod Base Tray Teether Toy Note: Tighten or loosen all screws with a Phillips screw- driver. Do not over-tighten the screws. #8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7 Shown Actual Size 3
Streszczenie treści zawartej na stronie nr. 4
Assembly IMPORTANT! Before assembly and each use, inspect this prod- uct for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. 3 • Align the holes in the plastic rings and the seat bottom tubes. • Insert a #8 x
Streszczenie treści zawartej na stronie nr. 5
Assembly Insert Screws Here Hinge Hinge Rod 4 6 • Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom. Tighten the screws. This may require • Turn the seat assembly face down. extra force. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw. Seat Back Pin Seat Back Pin • Set the seat assembly aside for Assembly step 9. Slot Slot 5 • Turn the seat bottom as
Streszczenie treści zawartej na stronie nr. 6
Assembly Frame Leg Seat Height Adjusters Position 4 Frame Decorated Side Press Lever Frame Back Legs 8 • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Seat Assembly Base Screw Retainers Sockets 7 • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. • Position a frame so that the decorated side is outward. • Fit the end of a base into the back leg of a frame. • Fit a screw retainer over the hole
Streszczenie treści zawartej na stronie nr. 7
Assembly PUSH PUSH Screw Retainers Base Seat Bottom Tube Ends 10 11 • Insert the frame front legs onto the remaining base. • Push each seat height adjuster to be sure they are completely on • Fit a screw retainer over a hole in the front leg. the seat bottom tubes. • Insert a #10 x 2,2 cm black screw through the screw retainer • Insert a #8 x 1,9 cm screw through each seat height adjuster and and front leg. Tighten the screw. the ends of the seat bottom tube. Tighten the screws. This may • R
Streszczenie treści zawartej na stronie nr. 8
Assembly Shoulder Straps Seat Bottom Tube Ends Crotch Strap 14 • Remove both shoulder straps from the seat back. • Remove the crotch strap from the seat back. Seat Height Adjusters 12 • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. This may require extra force. PRESS PRESS 13 15 • Squeeze the restraint release tabs together. • Fit t
Streszczenie treści zawartej na stronie nr. 9
Assembly Shoulder Straps Up Clips Lowest Slot Crotch Strap Down 16 • Fit the clips on the front edge of the pad onto the seat bottom. • Hook the elastic loops on each side of the pad onto the tabs in the seat back. 17 Hint: Do not unbuckle the restraint system. It is easier to attach or re-attach it to the product if it is buckled. • Grasp the restraint system so that the shoulder straps are up and the crotch strap is down. • Insert the end of the crotch strap through the lowest slot in
Streszczenie treści zawartej na stronie nr. 10
Assembly Shoulder Straps 18 Smaller Baby • Insert the ends of the shoulder straps through the lower slots in the pad. • From behind the product, attach the ends of the shoulder straps to the peg. 19 Larger Baby • From the front of the product, insert the ends of the shoulder straps through the upper slots in the pad and seat back. • From behind the product, attach the ends of the shoulder straps to the peg. 10
Streszczenie treści zawartej na stronie nr. 11
Secure Child Adjuster WARNING Prevent serious injury or death from falls or sliding out: The child should at all times wear a safety harness correctly fitted Free End and adjusted. The tray is not designed to hold the child in the chair. Anchored End Waist/Shoulder Belt Waist/Shoulder Belt TIGHTEN 2 • To tighten the waist straps: Feed the anchored end of the waist strap up through the buckle to form a loop A. Pull the free end of the waist strap B. • To tighten the shoulder straps: Hold th
Streszczenie treści zawartej na stronie nr. 12
Secure Child Shoulder Straps Shoulder Straps PRESS PRESS PRESS PRESS 5 4 • You can remove the shoulder straps and use only the To change strap slots: waist restraint. • From behind the product, squeeze the restraint release tabs • From behind the product, squeeze the restraint release tabs and and remove the shoulder straps. remove the shoulder straps. • From the front of the high chair, pull the shoulder portions • From the front of the product, pull to remove the shoulder straps of the re
Streszczenie treści zawartej na stronie nr. 13
Using the Trays WARNING Prevent serious injury or death from falls or sliding out: The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. PUSH Base Tray 7 • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward. Armrest PUSH 6 8 • Fit the base tray onto the seat armrests. Push down until the base tray "snaps" into place. • While pushing the release bar on the
Streszczenie treści zawartej na stronie nr. 14
Using the Trays Using the Teether Toy Teether Toy Food Tray Base Tray Tab 9 Slot • Fit the food tray into the base tray, as shown. Tab Hint: Before use, thorougly wash all parts (the trays) that may 10 contact food. The food tray is not microwave safe. • Insert and “snap” the teether toy tab into either slot in the tray. Hint: To remove the teether toy, press the tab and lift the toy. 14
Streszczenie treści zawartej na stronie nr. 15
Adjusting the Seat Hint: Adjust the seat height to any of seven positions! WARNING Prevent serious injury or death from Seat Height Adjuster falls or sliding out. It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position. Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline. Press Lever Upright Semi-Recline 12 Recline To adjust the seat height: • Press the levers on both seat height adjusters and
Streszczenie treści zawartej na stronie nr. 16
Storage Care • The pad, frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth. • The restraint system may be wiped clean or is machine washable. Machine wash in cold water on the gentle cycle. Do not use bleach. Line dry. Pull Frame Release Latch • The food tray, teether toy and restraint system are also top rack dishwasher safe (or use bottom rack - without using the drying cycle). To remove the pad: • Remove the elastic loops from the pegs on the back of
