Streszczenie treści zawartej na stronie nr. 1
CONTENTS
INTRODUCTION 1
mOUNTINg ReCOmmeND a TIONs 2
PRePaRa TION INsTRUCTIONs 3
faN INsT aLLa TION 4
CONTROL fea TURes:
INTELI•TOUCH OPERATION 8
INTELI•TOUCH TROUBLESHOOTING 11
ADVAN•TOUCH OPERATION 12
ADVAN•TOUCH TROUBLESHOOTING 15
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read thi
Streszczenie treści zawartej na stronie nr. 2
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount- ing recommendations as you decide where to install your Casablanca fan. • For safety r eason s , th e f an blad es m ust be a minim um o f 7 ′ above the floor. • D
Streszczenie treści zawartej na stronie nr. 3
® Shealtt STEALTH INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA LOCK™ HARDw ARE • ALLEN SET SCREw DOwNROD & BALL 1 1 ⁄4-20 x ⁄4” ASSEMBLY 3mm (PRE-INSTALLED) ALLEN wRENCH FAN PREPARATION impor TanT safeTy informa Tion! MOTOR BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN,
Streszczenie treści zawartej na stronie nr. 4
CEILING HARDw ARE addiTional hardware 1 2 /4” x 8-32 ROUNDED HEAD SCREw (2) CROSSBAR wIRE NUT (4) 1” x 8-32 ROUNDED MOUNTING FLAT w ASHER HEAD SCREw (2) BRACKET SUPPORT INSTALLATION PARTS LARGE LAG SCREw FLAT w ASHER 3 /8” #7 X 5” (1) 3 /8” (1) CROSSBAR MOUNTING BRACKET INSTALLATION JOIST note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or beam across its upper surface. If not, a 2” x 4” stud must be installed. Step 1. Remove the knocko
Streszczenie treści zawartej na stronie nr. 5
® Stlaeht LAG SCREw INSTALLATION Step 3. With the large washer attached, pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions. LAG SCREw LARGE w ASHER CANOPY HARDw ARE CANOPY SCREw (4) CA
Streszczenie treści zawartej na stronie nr. 6
ATTACHING THE BLADES 3a - BLADE TIP INSTALLATION: Step 3a. Attach the 5 blade tips to the blades using two 1 6-32x ⁄ ” round head screws provided. Note: the screws have 8 1 6-32 x ⁄ ” 8 locktite on them, so once they are installed it will be difficult ROUND HEAD BLADE to remove the screws. SCREw 1 Step 3b. Attach each of the five blades to the blade holders 6-32 x ⁄ ” 8 using four of the truss head screws and fiber washers pro- ROUND BLADE HEAD vided for each blade. The truss head screw
Streszczenie treści zawartej na stronie nr. 7
® Sheatlt CANOPY HATCH INSTALLATION Step 6. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the white and black wires are on HATCH CANOPY opposite sides of the canopy and all wires are clear of the CANOPY canopy opening. LOCK Step 7. Install canopy hatch with the last canopy screw w ASHER and lock washer. To do this, tilt the fan body away from the CANOPY hatch opening. SCREw Tip: Place the lock washer on the canopy screw, and the screw through the hatch before
Streszczenie treści zawartej na stronie nr. 8
® Int eli•T ouch INTELI•T OUCH INST ALLING THE W -32 W ALL CONTR OL The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only the Casablanca W-32 wall control. 4. No other light fixtures or electrical appliances may be 2. Do not use any additional contro
Streszczenie treści zawartej na stronie nr. 9
® Int eli•T ouch INTELI•T OUCH OPERA TION POwER The POwER button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POwER must be left on to retain a previously set fan speed or light level. INTELI•T OUCH OPERA TION SPEED CONTROL There are six individual speed settings for the fan; each speed is indicated FAN CONTROL by an audible tone of increasing pitch. To s
Streszczenie treści zawartej na stronie nr. 10
® Int eli•T ouch INTELI•T OUCH OPERA TION LIGHT-MINDER PROGRAM The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: POWER 1. Turn the POwER OFF for at least three seconds. POWER 2. Turn the on. 3. Immediately operate the buttons in the following sequence: LIGHT FAN FAN LIGHT + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons t
Streszczenie treści zawartej na stronie nr. 11
® Int eli•T ouch TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Changing Light Bulbs should be used to prevent scratching the finish. A vacuum cleaner Be sure to turn power to the fan OFF at the wall switch or circuit brush nozzle can remove heavier dust. Surface smudges or an ac- breaker before changing light bulbs. Replace bulbs with same type a
Streszczenie treści zawartej na stronie nr. 12
® ADVAN •TOUCH SAFETY FIRST w arning: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. AD v AN•T OUCH W -62 bRA CkET/HOLSTER REmO v AL Step 1. Remove the two 6-32 x 5/16” screws holding the bracket to the holster. Save screws for later. BRACKET HOLSTER AD v AN•T OUCH CONTR OL bRA CkET INST ALLA TION CAUTION! Do not use with wall dimmer. STANDARD ROCKER TOGGLE TYPE SwITCH LIGHT SwITCH INNER OUTER MOUNTING MOUNTING HOLES HOLES SwITCH
Streszczenie treści zawartej na stronie nr. 13
® ADVAN •TOUCH AD v AN•T OUCH bA TTER Y INST ALLA TION Open Battery Door Install 4 “AAA” alkaline by pressing down on batteries in the space the insert tab pro- provided. Please observe vided. proper polarity placement. Replace Battery Door. BATTERY DOOR AD v AN•T OUCH ImPOR T ANT OPERA TING NO TES Power turned off, interrupted or failure: The remote control is battery operated, therefore if the power is turned off, interrupted or you experience a power failure, the remote control remembe
Streszczenie treści zawartej na stronie nr. 14
® ADVAN •TOUCH SECURITY FEATURE Pressing the ‘SECURITY’ button will start the Security lighting program. The controller beeps and indicates ‘SECURITY’. The light will automatically turn ON and OFF in a seemingly random manner over an eight and a quarter hour programmed cycle that is designed to give the home a “lived-in” look. Regardless of the light setting when switching to the Security mode (lights on or off, dim or bright), the lights will increase to high brightness and then begin t
Streszczenie treści zawartej na stronie nr. 15
® ADVAN •TOUCH TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth Changing Light Bulbs should be used to prevent scratching the finish. A vacuum cleaner Be sure to turn power to the fan OFF at the wall switch or circuit brush nozzle can remove heavier dust. Surface smudges or an ac- breaker before changing light bulbs. Replace bulbs with same type a
Streszczenie treści zawartej na stronie nr. 16
PRODUCT SPECIFICATIONS ® ® Model Name: Stealth Motor: XLP-2000 Model Number: 32xxA/T Blade Span: 54" Blade Iron Pitch: 14° Dimensions: A = 10.8" No. of Blades: 5 B = 13.25" ® Technology: A dvan•T ou ch W-62 C = 3" NOTE: Dimension B ® In teli•T ou ch W-32 includes light fixture D = 11.5" and glass. Lightbulb: (1) 100-watt halogen lightbulb E = 5.6" Weight: 33 lbs. Airflow: 6,251 cfm Electricity Use*: 112 watts Airflow Efficiency*: 52.9 cfm/watt * Performance data is for fan
