Streszczenie treści zawartej na stronie nr. 1
2-In-1 Stand
Assembly Instructions
Model: BDS1642
Streszczenie treści zawartej na stronie nr. 2
Complete Stand Component Diagram � � �� �� � �� �� � � �� �� �� �� �� �� � �� �� �� � �� � �� �� �� � � �� �� �� 2
Streszczenie treści zawartej na stronie nr. 3
Parts Tools Required # Qty. Description 7/32" Allen Wrench (included) 1 1 TUBE, BOTTOM CROSS BRACE 2 1 ASSEMBLY, REAR LEFT STABILIZER 3 1 ASSEMBLY, REAR RIGHT STABILIZER You will also need: 4 2 ASSY, STAND LEG 9/16" Socket 9/16" Wrench or Adjustable Wrench 5 1 WELDMENT , LEFT DUMBBELL PLATFORM Utility knife or scissors to cut nylon ties 6 1 WELDMENT, RIGHT DUMBBELL PLATFORM 7 1 WELDMENT, TOWEL BAR 8 1 FOOT PEGS, SET OF FOUR 9 1 HOLD DOWN STRAPS, 2F 2M 10 20 NUT-NL 0.375-16 G2
Streszczenie treści zawartej na stronie nr. 4
step 1 � � �� �� �� �� Figure 1 Parts: • Stand Leg (#4) • Rear Left Stabilizer (#2) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 1-1 A ttach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1. Note: Do not tighten hardware. 4
Streszczenie treści zawartej na stronie nr. 5
step 2 � �� �� � �� �� Figure 2 Parts: • Stand Leg (#4) • Rear Right Stabilizer (#3) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2. Note: Do not tighten hardware. 5
Streszczenie treści zawartej na stronie nr. 6
step 3 � � �� �� � �� � � Figure 3 Parts: • Cross Brace (#1) • Left Stand Leg assembly from Step 1 • Right Stand Leg assembly from Step 2 Hardware Qty • 3" Screws (#12) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) 3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3) using the hardware shown in Figure 3. Make sure that the narrower edge of the Cross Brace (#1) is closer to the Stand Leg (#4) uprights. Note: Do not t
Streszczenie treści zawartej na stronie nr. 7
step 4 �� �� �� �� �� �� �� �� �� Figure 4 Parts: • Stand Leg and Cross Brace assembly from Step 3 • Center Plate (#17) Hardware Qty • 2.5" Screws (#14) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 4-1 I nstall the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4. Note: Make sure that the Center Plate edges are on the outer sides of the legs, and that the logo on the Plate is right side up.
Streszczenie treści zawartej na stronie nr. 8
step 5 � �� �� �� �� Figure 5 Parts: • Stand base assembly from Step 4 • Left Dumbbell Platform (#5) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 5-1 S ecure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in Figure 5. Note: Make sure the screw holes in the Platform are toward the center of the stand. 8
Streszczenie treści zawartej na stronie nr. 9
step 6 � �� �� �� �� Figure 6 Parts: • Stand base assembly from Step 5 • Right Dumbbell Platform (#6) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 6-1 S ecure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in Figure 6. Note: Make sure the screw holes in the Platform are toward the center of the stand. 9
Streszczenie treści zawartej na stronie nr. 10
step 7 � �� �� �� �� �� �� Figure 7 Parts: • Stand assembly from Step 6 • Towel Bar (#7) Hardware Qty • 1" Screws (#15) 4 • Washers (#11) 4 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 7-1 A ttach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) using hardware shown in Figure 7. Hand tighten screws in a cross pattern, to ensure even fit. 7-2 Tighten all screws securely. 10
Streszczenie treści zawartej na stronie nr. 11
step 8 � �� � Figure 8 Parts: • Stand assembly from Step 7 • Foot Pegs (#8) or Caster Wheels (#16) • Hold Down Straps (#9) 8-1 A ttach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear Right Stabilizer (#3), and both Stand Legs (#4). See Figure 8. 8-2 Attach the Hold Down Straps (#9) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) as shown in Figure 8. 11
Streszczenie treści zawartej na stronie nr. 12
16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS www.nautilus.com © 2006 Nautilus, Inc. All Rights Reserved. Bowflex and Bowflex SelectTech are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change. P/N 000-3708 RevB 02/06
