Streszczenie treści zawartej na stronie nr. 1
™
Installation Guide
CO2075DWR —
Combo Drawer Model
Ice Maker/Refrigerator
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005
Streszczenie treści zawartej na stronie nr. 2
™ CO2075DWR — Ice Maker/Refrigerator Contents 1 Follow Safety Precautions Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PLEASE READ all instructions completely before Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . . 5 attempting to install or operate the unit. Other Site Requi
Streszczenie treści zawartej na stronie nr. 3
™ CO2075DWR — Ice Maker/Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your CO2075DWR throughout this guide: Combo Drawer Model Ice Maker/Refrigerator with a package inside containing a User Manual, a Product WARNING Registration Card, water connection parts and Anti-Tip Kit. Complete and mail the Product Registration Card or SHOCK HAZARD
Streszczenie treści zawartej na stronie nr. 4
™ CO2075DWR — Ice Maker/Refrigerator Exterior Cleaning 3 Prepare Site (As Required) Your U-Line product has been designed for built-in Black Models: installation. Your unit does not require additional air The drawers, grille and cabinet may be cleaned with a space for top, sides or rear. However, the front grille must mild detergent and warm water solution. Do not use NOT be obstructed and clearance is required for water solvent-based or abrasive cleaners. Use a soft sponge and electrical
Streszczenie treści zawartej na stronie nr. 5
™ CO2075DWR — Ice Maker/Refrigerator Product Dimensions Clearances Information The unit must be installed in a wall or under a counter- top to allow for the installation of the Anti-Tip Kit (see 25-13/16" 23-11/16" Including Page 14). Handle WARNING The Anti-Tip Kit must be installed on this unit before it is used. Never use the drawers as steps 34-1/8" 34-1/8" or as a shelf to support more than the drawers’ contents. Serious personal injury could occur. The unit is designed so it can be ins
Streszczenie treści zawartej na stronie nr. 6
™ CO2075DWR — Ice Maker/Refrigerator The drawer unit can be installed with an appliance or Other Site Requirements fixture located in front of it, as long as there is adequate clearance for the drawer to be opened and removed Power Supply when servicing (see Figure 4). The unit requires a grounded and polarized 115 VAC, Note: U-Line recommends you consider additional 60 Hz, 15A circuit (normal household current). See clearance in front of the open drawer for convenience. Electrical Specifi
Streszczenie treści zawartej na stronie nr. 7
™ CO2075DWR — Ice Maker/Refrigerator Drawer Panel Installation 4 Prepare and Install Drawer Panel Install the insert as follows: (Black Units Only) CAUTION Two types of custom drawer panels can be installed on your Black unit to harmonize with or accent the Use care when handling the insert. Insert edges may be surrounding décor: Custom 1/4" Inserts or Full Overlays. sharp. Black units may also be installed with no custom drawer 1. Open drawer. Pull drawer panel. Handle gasket out of groov
Streszczenie treści zawartej na stronie nr. 8
™ CO2075DWR — Ice Maker/Refrigerator Attaching the Full Overlay Panel Full Overlay Drawer Panels 1. If user-supplied cabinet handles will be used, attach Drawer Panel Preparation their hardware to the overlay panel at this time. Full overlay drawer panels completely cover the drawer IMPORTANT fronts and handles to give a built-in appearance. Black units are shipped ready for full overlay installation. User-supplied cabinet handles MUST be counter bored to make sure mounting hardware is below
Streszczenie treści zawartej na stronie nr. 9
™ CO2075DWR — Ice Maker/Refrigerator CAUTION 5 Adjust Drawers It is important to ensure that all drilled holes are drilled to Checking Drawer Alignment the correct depth in order to avoid splits in the wood when hardware is installed. The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been 4. Remove tape adjoining the panels and enlarge the five disturbed during shipment or during overlay panel holes in the overlay panel using a 0.201" (#7) d
Streszczenie treści zawartej na stronie nr. 10
™ CO2075DWR — Ice Maker/Refrigerator Minor Adjustment: Adjusting Drawer Alignment Note: The mounting holes Loosen WARNING on the slide are slightly Mounting Screws larger than the screws’ diameter. SHOCK HAZARD — The unit must be unplugged from the wall outlet during drawer removal, 1. Loosen the slide’s adjustment and re-installation. mounting screws. Drawer Removal 2. Push the slide Push Slide backward. 1. Confirm that the unit is Backward Mounting unplugged from wall Screw 3. Retight
Streszczenie treści zawartej na stronie nr. 11
™ CO2075DWR — Ice Maker/Refrigerator Minor Adjustment: Minor Adjustment: Note: The mounting holes Note: The mounting holes Screws Should Loosen on the slide are slightly on the slide are slightly Be Loose Mounting Screws larger than the screws’ larger than the screws’ diameter. diameter. 1. Loosen one slide’s 1. Loosen one slide’s mounting screws. mounting screws. 2. Level the slide. 2. Push the slide upward Push Slide Upward or or downward to match Downward 3. Retighten the screws. Leve
Streszczenie treści zawartej na stronie nr. 12
™ CO2075DWR — Ice Maker/Refrigerator 2. Locate the compression fitting and ferrule packed with 6Prepare Plumbing the unit. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Do not use thread Plumbing installation must observe all state and local sealing compound or tape. Using two wrenches, codes. All water connections MUST BE made by a licensed/ tighten the compression fitting on the supply line (see qualified plumbing contractor. Failure to follow Figure 24
Streszczenie treści zawartej na stronie nr. 13
™ CO2075DWR — Ice Maker/Refrigerator 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not Electrical installation must observe all state and local level, the ice mold will not fill evenly. codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a 1. Use a level to check the qualified electrician. levelness of the unit from
Streszczenie treści zawartej na stronie nr. 14
™ CO2075DWR — Ice Maker/Refrigerator 9 Install the Unit Horizontal Mounting (Left Side Shown) Countertop or Wall Header Installation of the CO2075DWR 1. Make sure the ON/OFF switch is in the OFF position. B 2. Open the water supply valve in the main water source. 3. Plug in the power cord. 4. Gently push the unit into position. Be careful not to A kink the water supply line or entangle the electrical cord. 5. Re-check the leveling, from front to back and side to side. Make any necessary adju
Streszczenie treści zawartej na stronie nr. 15
OFF ON OFF ON ™ CO2075DWR — Ice Maker/Refrigerator 4. Using two of the screws (C) supplied, fasten the screws 10 Start-Up for the First Time through the bracket and into the counter, cabinet or wall. IMPORTANT Initial Start-Up Certain cabinets or countertops may require special Once installation and leveling is complete, the unit is fasteners or additional wood blocking to anchor properly. ready for initial start-up and operation. The ON/OFF switch is located in the front grille (see Figure
Streszczenie treści zawartej na stronie nr. 16
™ CO2075DWR — Ice Maker/Refrigerator Temperature Controller Start-Up Troubleshooting The temperature controller (Figure 32) is located in the top drawer. It consists of an LED display, two LED status Problem Q: indicator lights and three touchpad buttons. The LED Unit does not appear to turn on when switch is set to ON. display shows the refrigerator temperature set point and is calibrated in degrees Fahrenheit. The controller is Solution factory programmed for a set point of 38°F for the t
Streszczenie treści zawartej na stronie nr. 17
™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in underco
