Streszczenie treści zawartej na stronie nr. 1
Streszczenie treści zawartej na stronie nr. 2
WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturing’s obligations under this warranty shall be limited to the repair or exchange, at Buhler Manufacturing’s option, of any Buhler Manufacturing product or part which proves to be defective as
Streszczenie treści zawartej na stronie nr. 3
bühler Allied Front-End Loader 2595 & 2596 OPERATOR’S AND PARTS MANUAL Table of Contents Description Page Registration and Policy Loader Specifications .......................................................................................... 2 Introduction Terminology .............................................................................................. 4 Serial Decal Location ..........................................................................
Streszczenie treści zawartej na stronie nr. 4
bühler Allied Front-End Loader LOADER SPECIFICATIONS Illustration (TSL shown) - 2 - P4094
Streszczenie treści zawartej na stronie nr. 5
bühler Allied Front-End Loader Specification Chart 2595/2596 2595/2596 2595S/2596S 2595S/2596S Item Description REG TSL REG TSL A Maximum lift height to pivot pin [in/cm] 145/368 145/368 142/361 142/361 B Maximum lift height under level bucket [in/cm] 135/343 135/343 132/335 132/335 C Clearance with bucket dumped [in/cm] 112/285 112/285 108/274 108/274 D Reach at maximum lift height [in/cm] 29/74 28/71 32/81 32/81 E Maximum dump angle [deg] 48 49 46 48 G Maximum rollback an
Streszczenie treści zawartej na stronie nr. 6
bühler Allied Front-End Loader INTRODUCTION This manual has been provided as information regarding the specifications, safe operation and maintenance of your agricultural front-end loader. Read and understand this manual and the tractor manual prior to operating to obtain the best use of operating your loader. Keep this manual for reference and to forward to new operators and owners. Contact your local Buhler - Allied dealer if you require any assistance, information or additi
Streszczenie treści zawartej na stronie nr. 7
bühler Allied Front-End Loader Serial Decal Location: The serial decal is located on the inside left arm of the loader joint plate. Please record the serial number in the space provided for future reference. The serial decal will provide the model and date of manufacture of the loader and will be required to obtain correct replacement parts and complete warranty claims. Buhler Manufacturing For your records, record "a partnership" Serial Number here: __________________________
Streszczenie treści zawartej na stronie nr. 8
bühler Allied Front-End Loader SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate the loader properly. It is your responsibility to inform subsequent operators and owners of these precautions. General Safety Notes: Improper use of the loader and tractor can cause serious injury or death. Operate the loader while seated in the tractor seat only. Keep the work
Streszczenie treści zawartej na stronie nr. 9
bühler Allied Front-End Loader Safety Decals: Safety Decal Location illustrates the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper and align over the specified area. Carefully press in place. Slowly peel back the remaining paper and smooth the remaining portion in place. Small air poc
Streszczenie treści zawartej na stronie nr. 10
bühler Allied Front-End Loader Safety Decal Location - 8 - P4094
Streszczenie treści zawartej na stronie nr. 11
bühler Allied Front-End Loader The following pictorials indicate important precautions to be used during the operation of the loader. WARNING DANGER FALLING HAZARD ELECTROCUTION HAZARD To prevent serious injury or death: To prevent serious injury or death: Do not lift, carry or allow anyone to ride on or work from any Stay away from power lines and cables. portion of loader. Electrocution can occur with or without direct contact. WARNING WARNING CRUSHIN
Streszczenie treści zawartej na stronie nr. 12
bühler Allied Front-End Loader PRE – OPERATION WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injury or death caused by tractor roll over. CAUTION Maximum rated loader capacity may exceed tractor rating. Load restrictions or reduction in hydraulic operating pressure may be required for safe operation. Rops: Do not exceed the manufacturer’s rating for maximum gross vehicle weight.
Streszczenie treści zawartej na stronie nr. 13
bühler Allied Front-End Loader OPERATION General Operating Notes: The following section provides general information that can be applied towards your specific application. Ensure that you’ve read and understood this manual and your Tractor Manual. Observe all safety precautions and follow local laws pertaining to the use of your loader and tractor. Hydraulics: Under normal conditions, operate the tractor’s engine at ½ throttle. Note: In cold weather, tractors with load se
Streszczenie treści zawartej na stronie nr. 14
bühler Allied Front-End Loader All Buhler-Allied hydraulic valves are self-centering and return to neutral from all positions except float. The float or detent spool is only to be used on the boom circuit. This position allows the oil to freely flow through the valve so the lift cylinders can extend or retract. It can be engaged by slightly pushing control beyond full lower. Float will allow for the loader to lower and rise as the attachment follows the ground contours. To dise
Streszczenie treści zawartej na stronie nr. 15
bühler Allied Front-End Loader Minimize turning angle and length of run between pile and trailer to increase loading efficiency. Also, place load evenly or centered in the attachment. WARNING Carry the load no higher than necessary to clear the terrain. Turn and brake slowly. Always be sure that loading area is level and on solid ground. Do not raise loader higher then required while dumping. Immediately lower the loader to ground if the tractor becomes unstable.
Streszczenie treści zawartej na stronie nr. 16
bühler Allied Front-End Loader For back grading, either load the bucket and position the heel on the ground or position the bucket at 40 ° or less below level as shown. Place the valve in the float position and back up slowly. IMPORTANT: Float position must be used to reduce down pressure, otherwise cylinder rod(s) and/or bucket damage could occur. A – Frame: Standard and Heavy Duty A – Frames can be fitted with either spears or pallet forks. - Standard
Streszczenie treści zawartej na stronie nr. 17
bühler Allied Front-End Loader Handling bales and pallets: For safe handling of bales and pallets please follow procedures below: WARNING Do not operate A – Frame for bales without the stabilizers. With a single spear, enter one of the ends of the bale and drive the spear horizontally into the center or slightly above center of the bale and fully penetrate the bale. Then rollback the bucket cylinders approximately three quarters of the cylinder stroke and lift bale
Streszczenie treści zawartej na stronie nr. 18
bühler Allied Front-End Loader When loading bales onto a trailer, park trailer in close proximity to minimize turning angle and length of travel to increase loading efficiency. As you lift the bale using the regular loader, it is recommended to feather the valve to allow bucket cylinders to extend to keep bale at about a 20 ° angle. (On TSL loaders this is not necessary) Lift the bale only enough to clear the area that the bale will be placed on. Always approach the traile
Streszczenie treści zawartej na stronie nr. 19
bühler Allied Front-End Loader Grapple: The grapple is designed to safely prevent loads (bales, silage) from falling out of the bucket. (Refer to pictorial below for options listed) WARNING Travel at low speeds. Carry loads as low as possible. Avoid sharp turns and uneven terrain. Grapple for Hay or Silage Standard 2000 series Quick attach brackets (2495-2895) Standard 495-995 Quick attach Optional 95-395 Quick attach Optional factory pre punched grapple buckets. (84",
Streszczenie treści zawartej na stronie nr. 20
bühler Allied Front-End Loader INSTALLING / REMOVING LOADER Installing: CAUTION Prior to initial mounting, cycle loader cylinders to displace air. This ensures the loader will remain in the storage position and operate consistently. 1. Position the tractor centrally and parallel to the loader uprights. Drive forward slowly until the loader hydraulic hoses can be coupled. Shut tractor off and set park brake. Couple the loader hoses to the matched color code identi
