Instrukcja obsługi Field Controls WML-C

Instrukcja obsługi dla urządzenia Field Controls WML-C

Urządzenie: Field Controls WML-C
Kategoria: Piec
Producent: Field Controls
Rozmiar: 0.89 MB
Data dodania: 9/17/2013
Liczba stron: 40
Drukuj instrukcję

Pobierz

Jak korzystać?

Naszym celem jest zapewnienie Ci jak najszybszego dostępu do treści zawartych w instrukcji obsługi urządzenia Field Controls WML-C. Korzystając z podglądu online możesz szybko przejrzeć spis treści i przejść do strony, na której znajdziesz rozwiązanie swojego problemu z Field Controls WML-C.

Dla Twojej wygody

Jeżeli przeglądanie instrukcji Field Controls WML-C bezpośrednio na tej stornie nie jest dla Ciebie wygodne, możesz skorzystać z dwóch możliwych rozwiązań:

  • Przeglądanie pełnoekranowe - Aby wygodnie przeglądać instrukcję (bez pobierania jej na komputer) możesz wykorzystać tryp przeglądania pełnoekranowego. Aby uruchomić przeglądanie instrukcji Field Controls WML-C na pełnym ekranie, użyj przycisku Pełny ekran.
  • Pobranie na komputer - Możesz również pobrać instrukcję Field Controls WML-C na swój komputer i zachować ją w swoich zbiorach. Jeżeli nie chcesz jednak marnować miejsca na swoim urządzeniu, zawsze możesz pobrać ją w przyszłości z ManualsBase.
Field Controls WML-C Instrukcja obsługi - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Wersja drukowana

Wiele osób woli czytać dokumenty nie na ekranie, lecz w wersji drukowanej. Opcja wydruku instrukcji również została przewidziana i możesz z niej skorzystać klikając w link znajdujący się powyżej - Drukuj instrukcję. Nie musisz drukować całej instrukcji Field Controls WML-C a jedynie wybrane strony. Szanuj papier.

Streszczenia

Poniżej znajdziesz zajawki treści znajdujących się na kolejnych stronach instrukcji do Field Controls WML-C. Jeżeli chcesz szybko przejrzeć zawartość stron znajdujących się na kolejnych strinach instrukcji, możesz z nich skorzystać.

Streszczenia treści
Streszczenie treści zawartej na stronie nr. 1

Installation, Operation and
Maintenance Manual
Oil Fired Warm Air Furnaces


WML-C AND MPL-B
(Down-Flow or Horizontal Model)
ALL INSTALLATIONS MUST MEET ALL
LOCAL, PROVINCIAL/STATE, AND
FEDERAL CODES WHICH MAY
DIFFER FROM THIS MANUAL

ECR International Limited
OLSEN Division
Read this complete manual before
beginning installation. These
instructions must be kept with the
furnace for future reference.

Streszczenie treści zawartej na stronie nr. 2

TABLE OF CONTENTS INTRODUCTION..........................................................................................................................................................................3 HEAT LOSS.................................................................................................................................................................................3 LOCATION OF UNIT ........................................................................................

Streszczenie treści zawartej na stronie nr. 3

enable proper sizing of the trunk and branch ductwork. In retrofit applications, a building shell (overall) heat loss IMPROPER INSTALLATION MAY DO NOT USE GASOLINE, calculation may be used. CREATE A CONDITION WHERE THE CRANKCASE OIL, OR ANY OTHER In the United States, Manual J. titled, OPERATION OF THE PRODUCT OIL CONTAINING GASOLINE AS A "Load Calculation" published by the Air COULD CAUSE PERSONAL INJURY FUEL FOR THIS FURNACE. Conditioning Contractors of America, OR PROPERTY DAMAG

Streszczenie treści zawartej na stronie nr. 4

HORIZONTAL INSTALLATION Table 1: Clearance to Combustibles WML-C AND MPL-B furnaces models WML-C MPL-B Furnace are assembled and shipped ready for installation in the down-flow position. The Location Down flow Horizontal Down flow Horizontal furnace may be installed in either of the Top 0 in. 3 in. 0 in. 3 in. horizontal positions; warm air discharging left or warm air-discharging Bottom 1 in. 1 in. 1 in. 1 in. right by following these steps: S/A Plenum 1 in. 1 in. 1 in. 1 in. 1.

Streszczenie treści zawartej na stronie nr. 5

through a refrigeration unit unless the If the chimney serves the WML-C unit is specifically approved for such furnace only, the vent should be sized at service. 5-inch minimum. The MPL-B should be THE FURNACE MUST BE 6-inch minimum. The data provided in Generally, a six-inch clearance between CONNECTED TO A FLUE HAVING Table 3 is based on dedicated venting. If the air conditioning evaporator coil and SUFFICIENT DRAFT AT ALL TIMES TO the furnace is to be co-vented with other the he

Streszczenie treści zawartej na stronie nr. 6

Fig. 2: Common Chimney Problems Can be found Obstruction in by light and Use weight to chimney D mirror reflecting break and conditions in dislodge. chimney. Must be Lowering a light handled by Joist protruding E on an extension competent into chimney. cord. masonry contractor. Smoke test - build smudge Must be fire blocking off handled by Break in F other opening, competent chimney lining. watching for masonry smoke to contractor. escape. Clean out with Collection

Streszczenie treści zawartej na stronie nr. 7

In general, the oil tank must be properly Table 4: Oil Lines OPTIONAL SIDE WALL VENTING supported and remain stable in both Certain WML-C AND MPL-B furnace Copper Tubing Oil Line Length (Feet) empty and full condition. The oil tank models are manufactured to be installed must be fitted with vent and supply pipes Single-Pipe OD Two-Pipe OD Lift as sidewall vented units. Please refer to to the outdoors. Refer to the above- (Feet) 3/8” 1/2” 3/8” 1/2” Direct Venting Instructions, P/N

Streszczenie treści zawartej na stronie nr. 8

main electrical panel; however, 2. Connect an ammeter between the If the limit control opens with the United accessory equipment such as electronic wire and the thermostat terminal to Technologies 1158-120 electronic fan control, the circulating fan will be air cleaners and humidifiers may be which it was attached. included on the furnace circuit. Although energized as well. When the limit closes, 3. Note the amperage reading when a suitably located circuit breaker can be the control initi

Streszczenie treści zawartej na stronie nr. 9

trunk ducts. These systems may require into contact with the furnace heat box, tape off both ends of the unused modification to provide some resistance exchanger. Do not use direct drive motor wire. to the airflow to prevent over-amping of connections as a source of power for the direct drive blower motor. Selecting a 120 VAC humidifiers and humidifier lower blower speed may correct this transformers. problem. DISCONNECT THE POWER SUPPLY OIL BURNER Direct drive blower speeds are adju

Streszczenie treści zawartej na stronie nr. 10

BURNER ELECTRODES PROCEDURE: excess air, or contaminated fuel. Do not ignore this indicator. Correct positioning of the electrode tips Start the burner and allow it to run at STACK TEMPERATURE: with respect to each other, to the fuel oil least ten minutes. Set the air shutter to nozzle, and to the rest of the burners is give a good flame visually. The Stack temperature will vary depending essential for smooth light ups and proper combustion air supply to the burner is on fuel input, circ

Streszczenie treści zawartej na stronie nr. 11

used in conjunction with multi-meters anywhere within the heating system B: Annual Service By Contractor with temperature measurement which may cause some concern or capabilities. annoyance to the home owner, etc. The return air should be measured at a F) Be sure that the homeowner is THE COMBUSTION CHAMBER point where the thermometer will be well familiar with the furnace. The (FIREPOT) IS FRAGILE. USE CARE within the air stream near the furnace homeowner should be aware of the WHEN

Streszczenie treści zawartej na stronie nr. 12

should be checked to ensure that all fan furnace and set the thermostat above speeds are operating properly. room temperature. After three or four minutes of burner operation, the limit OPERATING INSTRUCTIONS control should turn the burner off. When the limit function test is complete, shut Before Lighting off electrical power to the furnace, Open all supply and return air registers replace the neutral wire to the blower fan and grilles. motor, and then restore power. The blower fan

Streszczenie treści zawartej na stronie nr. 13

APPENDIX A- WML-C AND MPL-B BURNER SET UP WML-C AND MPL-B furnaces may be used with the following oil burners. Please note: The Beckett AF, and Riello 40F oil burners are for applications using indoor air for combustion only. For sidewall venting applications utilizing outdoor air for combustion, use the Beckett AFII or the Riello 40BF (Balanced Flue) oil burners only. Table A-1 Beckett AF Oil Burner Set-Up Beckett AF Series Oil Burners (For use with chimney vented units only) Furnace

Streszczenie treści zawartej na stronie nr. 14

Table A-4 Riello Balanced Flue (BF) Burner Set-Up Riello Balanced Flue Series Oil Burners (For use with sidewall vented units using outdoor combustion air) Furnace Output Burner Pump Turbulator Nozzle Flow Rate Model BTU/Hr Model Pressure Setting WML-60CRB 59,500 40BF3 0.50 / 60°W 105 PSIG 0.51 USGPH 1.0 WML-80CRB 75,000 40BF3 0.60 / 60°W 115 PSIG 0.65 USGPH 1.5 WML-90CRB 85,600 40BF3 0.65 / 60°W 135 PSIG 0.75 USGPH 2.0 NOTE: Air gate setting may vary for sidewall vented units where air

Streszczenie treści zawartej na stronie nr. 15

Table A-6 Direct Drive Blower Set-Up Blower Set-Up Cooling Capacity Furnace Blower 0.20 in. w.c. 0.50 in. w.c. Model Tons Power CFM Range Speed Motor Speed Motor WML-60C GT10 DD Low ½ HP Med-Low ½ HP 3 ½ HP 763 – 1505 WML-80C GT10 DD Med-Low ½ HP Med-High ½ HP 3 ½ HP 763 – 1505 WML-90C GT10 DD Med-High ½ HP High ½ HP 3 ½ HP 763 – 1505 3 MPL-90B GT12-10DD Low ¾ HP Med-High ¾ HP ¾ HP 1185 – 1553 3 MPL-100B GT12-10DD Med-High ¾ HP High ¾ HP ¾ HP 1185 – 1553 3 MPL-120B GT12-10DD Hig

Streszczenie treści zawartej na stronie nr. 16

Table A-9 General Dimensions (Inches) Cabinet Plenum Openings Filter Flue Furnace Shipping Diameter Return Width Depth Height Supply Model Weight Type Size H A B C D x E Side Bottom WML-C 22 22-1/8 55-1/4 19 x 19 18 x 18 18 x 18 5 Permanent 20 x 20 x 1 265 20-1/2 x 20- MPL-B 22-1/4 22-1/4 62 18 x 18 18 x 18 6 Permanent 20 x 20 x 1 292 1/2 WML-C & MPL-B Down flow WML-C & MPL-B Horizontal 30318 R4 9/9/2005 16

Streszczenie treści zawartej na stronie nr. 17

APPENDIX B: WIRING DIAGRAMS Beckett AF Burner Wiring Diagram 30318 R4 9/9/2005 17

Streszczenie treści zawartej na stronie nr. 18

Beckett AFII Burner Wiring Diagram 30318 R4 9/9/2005 18

Streszczenie treści zawartej na stronie nr. 19

Riello 40F3 and F5 Burner Wiring Diagram 30318 R4 9/9/2005 19

Streszczenie treści zawartej na stronie nr. 20

Riello 40BF3 Burner Wiring Diagram 30318 R4 9/9/2005 20


Podobne instrukcje
# Instrukcja obsługi Kategoria Pobierz
1 Field Controls MPL-B Instrukcja obsługi Piec 0
2 Adams Condensing Oil-Fired Instrukcja obsługi Piec 2
3 AirComm Corporation 10016 Instrukcja obsługi Piec 0
4 AirComm Corporation 7516 Instrukcja obsługi Piec 0
5 AirComm Corporation 50 Instrukcja obsługi Piec 0
6 Air King 9320 Instrukcja obsługi Piec 2
7 Air King 9718 Instrukcja obsługi Piec 5
8 AirComm Corporation 7512 Instrukcja obsługi Piec 1
9 Allied Air Enterprises A80UH Instrukcja obsługi Piec 8
10 Allied Air Enterprises 92G1DF Instrukcja obsługi Piec 0
11 Allied Air Enterprises 95G1DF Instrukcja obsługi Piec 0
12 American Standard 32-5037-01 Instrukcja obsługi Piec 1
13 American Standard Condensing Gas s Fan Assisted Combustion System Upflow Horizontal and Downflow Horizontal Instrukcja obsługi Piec 0
14 American Standard Noncondensing Gas s Instrukcja obsługi Piec 1
15 Amana Gas Furnance GME8 Instrukcja obsługi Piec 0