Streszczenie treści zawartej na stronie nr. 1
Angle Grinder
180 mm (7”)
MODEL 9067L
230 mm (9”)
MODEL 9069
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Streszczenie treści zawartej na stronie nr. 2
SPECIFICATIONS model 9067L 9069 No load speed (RPM) 6,000/min 6,000/min Overall length 458 mm (18”) 458 mm (18”) Net weight 4.2 kg (9.3 lbs) 4.2 kg (9.3 lbs) Spindle thread 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serio
Streszczenie treści zawartej na stronie nr. 3
5. Avoid body contact with grounded sur- be used for appropriate conditions. Ordinary faces such as pipes, radiators, ranges and eye or sun glasses are NOT eye protection. refrigerators. There is an increased risk of Tool Use and Care electric shock if your body is grounded. 15. Use clamps or other practical way to 6. Do not expose power tools to rain or wet secure and support the workpiece to a conditions. Water entering a power tool will stable platform. Holding the work by hand or increase th
Streszczenie treści zawartej na stronie nr. 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Streszczenie treści zawartej na stronie nr. 5
8. Be careful not to damage the spindle, the poor installation or a poorly balanced flange (especially the installing surface) wheel. or the lock nut. Damage to these parts 15. Use the specified surface of the wheel to could result in wheel breakage. perform the grinding. 9. NEVER use tool with wood cutting blades 16. Watch out for flying sparks. Hold the tool or other sawblades. Such blades when so that sparks fly away from you and other used on a grinder frequently kick and persons or flammabl
Streszczenie treści zawartej na stronie nr. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001026 Shaft lock CAUTION: 1 • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001041 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns t
Streszczenie treści zawartej na stronie nr. 7
001064 Installing or removing wheel guard 1 CAUTION: • When using a depressed center grinding wheel/Multi- disc, flex wheel or wire wheel brush, the wheel guard must be fitted on the tool so that the closed side of the 3 guard always points toward the operator. 2 Mount the wheel guard with the protrusion on the wheel 1. Wheel guard guard band aligned with the notch on the bearing box. Then 2. Bearing box 3. Screw rotate the wheel guard around 180 degrees. Be sure to tighten the screw securely. T
Streszczenie treści zawartej na stronie nr. 8
001101 Installing or removing flex wheel 1 (optional accessory) 2 3 WARNING: 4 • Always use supplied guard when flex wheel is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. Follow instructions for depressed center grinding wheel/ 1. Lock nut 2. Flex wheel Multi-disc but also use plastic pad over wheel. See order of 3. Plastic pad assembly on accessories page in this manual. 4. Inner flange 001112 Installing or removing abrasive disc 1 (optional acce
Streszczenie treści zawartej na stronie nr. 9
CAUTION: • After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. 001127 Grinding and sanding operation ALWAYS hold the tool firmly with one hand on rear handle and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. 15˚ During the break-in period with a new wheel, do not work
Streszczenie treści zawartej na stronie nr. 10
001234 Operation with wire wheel brush (optional accessory) 1 CAUTION: • Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not use wire wheel brush that is damaged, or which 1. Wire wheel brush is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. • ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. W
Streszczenie treści zawartej na stronie nr. 11
001146 Replacing carbon brushes When the resin insulating tip inside the carbon brush is 2 exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should 1 be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at 3 the same time. Use only identical carbon brushes. 1. Commutator 2. Insulating tip 3. Carbon brush 001154 Use a screwdriver to remove the brush holder caps. Take out
Streszczenie treści zawartej na stronie nr. 12
001184 1 2 2 8 2 12 3 3 9 11 13 4 6 10 5 7 5 9067L/9069 1 Grip 36 2 Wheel guard 3 Inner flange 89 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/8-40 6 Plastic pad 7 Flex wheel 8 Rubber pad 170 9 Abrasive disc 10 Sanding lock nut 5/8-48 11 Wire wheel brush 12 Urethane washer 14 13 Wire cup brush - Lock nut wrench 28 12
Streszczenie treści zawartej na stronie nr. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Streszczenie treści zawartej na stronie nr. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Streszczenie treści zawartej na stronie nr. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO LOUISIANA NEW YORK PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 5626 Jefferson Hwy. 4917 Genessee Street 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Harahan, LA 70123 Cheektowaga, NY 14225 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (504) 733-4138 (716) 685-9503 (787) 250-8776 131-35 31st Ave. ARIZONA FLORIDA MARYLAND Flushing, NY 11354 TENNESSEE 3707 E. Broadway Rd., Ste. 6 62
Streszczenie treści zawartej na stronie nr. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
