Streszczenie treści zawartej na stronie nr. 1
Nautilus® Nautilus® Nautilus® U514 U514 U514 Upright Upright Upright Exercise Exercise Exercise Bike Bike Bike
003–3242–110609C
Streszczenie treści zawartej na stronie nr. 2
Para obtener este manual en Español Latino Americano vaya a: http://support.nautilus.com. Table of Contents 3 Parts 6 Important Safety Instructions 4 7 Specifications Assembly Before Assembly 4 Level Y our Bike 20 T ools Required 5 21 Contacts 5 Hardware Instructions de montage 23 © 2009 Nautilus, Inc., All rights reserved ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (www .nautilus.com) trademarks include NAUTILUS®, BOWFLEX®, ST AIRMASTER®, SCHWINN® and UNIVERSAL® and res
Streszczenie treści zawartej na stronie nr. 3
Important Safety Instructions This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury . Obey the following warnings: Read and understand all warnings on this machine. Carefully read and understand the Assembly Manual. • • • Keep bystanders and children away from the product you are assembling at all times. • • • Do not connect power supply to the machine until instructed to do so. • • • Do not assemble equipment in a wet or damp location.
Streszczenie treści zawartej na stronie nr. 4
Specifications Before Assembly Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a hard, level surface. Allow a workout area of minimum 82” x 61” (2.1m x 1.5m). Follow these basic points when you assemble your machine: 1. Read and understand the “Important Safety Instructions” before assembly. 2. Collect all the pieces necessary for each assembly step. 3. Using the recommended wrenches, turn the bolts and nuts to the right (clockw
Streszczenie treści zawartej na stronie nr. 5
Tools Included Not Included 6mm Hardware Item Qty Description Item Qty Description 1 2 A M8 x 85 Hex Bolt G Flat W asher B 1 M8 x 85 Carriage Bolt H 1 M8 Lock Nut C 4 M8 x 16 Hex Screw I 1 T -Nut 4 1 D M8 x 16 Button Head Hex Screw J Narrow W asher E 4 Arc W asher K 1 Console slider adjustment knob F 4 Cover L 1 Console tilt adjustment knob 5 5 5
Streszczenie treści zawartej na stronie nr. 6
Parts Item Qty Description Item Qty Description 1 1 8 1 Rear Stabilizer Console 2 1 Front stabilizer 9 1 Console Bracket 3 1 Main Frame 10 1 W ater Bottle Holder 4 1 11 1 Seat Power Cord 5 1 1 Seat Post 12 Right Pedal 6 1 Console Mast 13 1 Left Pedal 7 1 Handlebar 6 6 6
Streszczenie treści zawartej na stronie nr. 7
Assembly 1. Install Front and Rear Stabilizers 7 7 7
Streszczenie treści zawartej na stronie nr. 8
2. Install Pedals 8 8 8
Streszczenie treści zawartej na stronie nr. 9
3. Install Seat Post 9 9 9
Streszczenie treści zawartej na stronie nr. 10
4. Install Seat 10 10 10
Streszczenie treści zawartej na stronie nr. 11
5. Connect Console Mast Cable to Frame Assembly Cable 11 11 11
Streszczenie treści zawartej na stronie nr. 12
6. Attach Console Mast NOTICE: Do not crimp Console Cable. 12 12 12
Streszczenie treści zawartej na stronie nr. 13
7. Install Handlebar Note: Put the T -nut (I) into the Handlebar slider and align it with the second hole (7a) to install the Console Slider Adjustment Knob (K) and washer (J). Make sure that the lower Heart Rate cable (7b) is connected. NOTICE: Do not crimp the cables. 13 13 13
Streszczenie treści zawartej na stronie nr. 14
8. Install Console Bracket NOTICE: Do not crimp the cables. 14 14 14
Streszczenie treści zawartej na stronie nr. 15
9. Connect Console Mast Cable and Heart Rate Cable to Console 15 15 15
Streszczenie treści zawartej na stronie nr. 16
10. Attach Console to Console Bracket Note: Hardware is pre-installed on Console and not on Hardware Card. NOTICE: Do not crimp the cables. 16 16 16
Streszczenie treści zawartej na stronie nr. 17
11. Adjust and Tighten the Console Mast 17 17 17
Streszczenie treści zawartej na stronie nr. 18
12. Install Water Bottle Holder Note: Hardware is pre-installed on Mast and not on Hardware Card. 18 18 18
Streszczenie treści zawartej na stronie nr. 19
13. Connect Power Cord to Frame Assembly Final Inspection Inspect your machine to ensure that all fasteners are tight and components are properly assembled. Do not use or put the machine into service until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’ s Manual. 19 19 19
Streszczenie treści zawartej na stronie nr. 20
Level Your Bike Levelers are found on each side of the Rear Stabilizer . T urn the knob to adjust the stabilizer foot. Make sure the bike is level and stable before you exercise. 20 20 20
