Streszczenie treści zawartej na stronie nr. 1
TABLETOP PAPER SHREDDER
Model 93499
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be repr
Streszczenie treści zawartej na stronie nr. 2
PRODUCT SPECIFICATIONS Waste Basket Dimensions 1-3/8” L x 4-1/4” W x 4-5/16” H Strip Size 0.14” Wide Cutter Housing Dimensions 10-1/2” L x 4-3/4” W x 1-3/4” H Sheet Capacity 1 (#20WT.) Power Source 6 “AA” Batteries or 120 Volts AC, DC9V 1.2A Adapter (not included) Weight 1.65 Lbs. Note: This unit works on “AA” batteries or on an AC Adapter that is NOT in- cluded. The following manual addresses safety issues for both applications. SAVE THIS MANUAL You will need this manual for the safety warning
Streszczenie treści zawartej na stronie nr. 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insu
Streszczenie treści zawartej na stronie nr. 4
12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Plugging in Paper Shredders with the Power Switch on, invites accidents. TOOL USE AND CARE 13. Do not force the Paper Shredders. Allow the Shredder to work at its own speed. 14. Do not use the Paper Shredder if the Power Switch does not turn it on or off. Any Paper Shredder that cannot be controlled with the Power Switch is dangerous and must be replaced. 15. Disconnect the Power Cord Plug from the power source
Streszczenie treści zawartej na stronie nr. 5
SERVICE 20. Service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 21. When servicing a Shredder, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and namepla
Streszczenie treści zawartej na stronie nr. 6
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet insta
Streszczenie treści zawartej na stronie nr. 7
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B EXTENSIO
Streszczenie treści zawartej na stronie nr. 8
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NA
Streszczenie treści zawartej na stronie nr. 9
UNPACKING When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY AND OPERATING INSTRUCTIONS CAUTION: Always make sure the Power Cord of the Paper Shredder is un- plugged from its electrical outlet prior to installation. FIGURE 1 Switch For technical questions, please call 1-800-444-3353. Page 9 SKU 93499
Streszczenie treści zawartej na stronie nr. 10
FIGURE 2 To remove or replace the “AA” batteries, open the plastic lid on the bottom of the unit. Remove the old and replace with new batteries making sure that the polarity on the batteries match the polarity on the battery housing. Caution! Do not use an AC adapter if you are using non-rechargeable batteries. An AC adapter will try to charge the batteries and in doing so will damage the unit. You may use an AC adapter with rechargeable batteries. An AC adapter is not included. Caution: Do
Streszczenie treści zawartej na stronie nr. 11
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the Power Switch of the Paper Shredder is in its “OFF” position, that the batteries are removed, and that the unit is unplugged from its electrical outlet before performing any inspection, maintenance, or clean- ing procedures. 2. BEFORE EACH USE, inspect the general condition of the Paper Shredder. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other
Streszczenie treści zawartej na stronie nr. 12
Troubleshooting Note: The housing of this unit may eventually fill with paper shavings. If this occurs, the bin must be cleaned out by a qualified service technician. Problem: Paper is hanging from the Shredder exit after finishing. Cause: Paper is clogging the machine. Solution: Set the unit to “REV” (reverse) and remove the scraps. Problem: Paper is not feeding properly. Cause: Paper isn’t straight in the feeder. Solution: Reposition paper so that both corners enter together. P
