Instrukcja obsługi Royal Sovereign RSC Series

Streszczenie treści zawartej na stronie nr. 1

17. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the custome

Streszczenie treści zawartej na stronie nr. 2

RSC Series TABLE OF CONTENTS 1. INTRODUCTION TOPIC PAGE Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and 1. Introduction.......................................................................................................... 2 maintenance information please read this manual thoroughly. Upon receipt of your 2. Safety Precautions........................................................

Streszczenie treści zawartej na stronie nr. 3

! RSC Series 3. INSTALLATION 4. INCLUDED WITH LAMINATOR Thoroughly inspect the parts and the unit. It is imperative that any missing parts are Note: The laminator should be installed by a trained service technician.

Streszczenie treści zawartej na stronie nr. 4

Streszczenie treści zawartej na stronie nr. 5

" ! " ! " ! " !

Streszczenie treści zawartej na stronie nr. 6

RSC Series 10. USING CROSS CUTTER 11. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). The cross cutter is located on the rear exit table of the machine. Loading films to the top and bottom film shafts: (See page 5 for assistance with parts identification.) 1. After lamination, move the cutter approximately to 1. Remove the top and bottom film shafts from the the center of the completed application at the machine. desired point o

Streszczenie treści zawartej na stronie nr. 7

RSC Series 9. Cut and separate the release liner and the film. 12. THREADING FILM (Figure 3) Figure 3 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) only RSC-1650HR 12.1. Decaling 11. Reinstall the Feed Table and the Frame-Paper 1. Turn the power switch on (“I” position). The Power Figure 4 Guide,and close the Safety Cover. switch is located on the rear left side of the unit. 12

Streszczenie treści zawartej na stronie nr. 8

RSC Series 17. Press the Stop button when the leader board has completely exited from the rollers. 4. Flip the image over the top roller and hold on to the release liner (Figure 4). 18. Use the Cross Cutter to cut the leader board from the web (see page 9). 19. Set the nip setting to the appropriate position for the Over-lamination / Decaling application. Figure 4 12.2. Mounting 1. Lay the decaled image face down on a flat surface. 5. Press the foot pedal once, and then let it go while Careful

Streszczenie treści zawartej na stronie nr. 9

RSC Series 4. Disassemble the power switch bracket and place the left 13. INSTALLATION OF FRONT FEEDER and REAR rewinder outside of the frame; fasten with round head REWINDER OPTIONS 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 7). Note: Below options are to be installed by an authorized RS reseller. Figure 7 Installation of the Front Feeder Option (Includes 2 brackets, one spindle, and mounting hardware). 5. Install the right rewinder on th

Streszczenie treści zawartej na stronie nr. 10

RSC Series 14. MAINTENANCE 16. SPECIFICATIONS Cleaning the Body of the laminaor 1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean. Removing Adhesive Build Up 1. Remove the film from the laminator. 2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers. Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool