Streszczenie treści zawartej na stronie nr. 1
Sheraton
Free Standing Stove
ModelS : 7016/7017/7027
Instructions for Use,
Installation and Servicing
For use in Great Britain and Republic of Ireland.
This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the translated
instructions and in some cases the appliance will require modification. Contact Stovax for further information.
IMPoRTANT
This appliance will become hot whilst in operation, it is
Streszczenie treści zawartej na stronie nr. 2
CoVeRING THe FolloWING ModelS: 7016/7017/7027 PAGe APPlIANCe CoMMISSIoNING CHeCKlIST 3 oPeRATING INSTRUCTIoNS 4 INSTAllATIoN INSTRUCTIoNS 9 Technical Specifications 9 Site Requirements 10 Pre-Installation 13 Installation 15 Commissioning 17 SeRVICING INSTRUCTIoNS 18 Maintenance & Servicing 18 Basic spare parts list 21 Care of your stove 23 Service Records 24 2
Streszczenie treści zawartej na stronie nr. 3
APPlIANCe CoMMISSIoNING CHeCKlIST To assist us in any guarantee claim please complete the following information:- dealer appliance was purchased from Name: ................................................................................................................................................................. Address: ............................................................................................................................................................... ............
Streszczenie treści zawartej na stronie nr. 4
oPeRATING INSTRUCTI oNS Before using this appliance, please read these instructions carefully. 1. GeNeRAl 1.1 This stove is designed for domestic heating and should only be used for this purpose, and in accordance with the manufacturers operating instructions. 1.2 It must be installed by a competent installer, in accordance with all local regulations, including those referring to national and european standards. 1.3 The stove should only be used to burn approved fuels and should not be use
Streszczenie treści zawartej na stronie nr. 5
oPeRATING INSTRUCTI oNS 3.3 Fuel consumption at nominal heat output. dooR HANdle As tested at nominal heat output to the requirements of EN 1.12 To open and Close: Use a protective gloved hand to 13240: 2001 for intermittent operation. operate. Fuel Consumption 1.13 Rotate RH Knob anti-clockwise to open. Rotate clockwise to Kg/hour close. Kg/hour Description Briquetted Wood Smokeless fuel Sheraton 7016 2.66 - Sheraton 7017 2.66 1.12 Sheraton 7027 2.66 1.12 3.4 If you require advice on suitab
Streszczenie treści zawartej na stronie nr. 6
oPeRATING INSTRUCTI oNS 4.9 The ideal control settings to suit the particular installation fuel. Allow the new fuel to burn at high output for a few and personal preferences will be established by experience minutes before adjusting the burn rate with the Primary/ in using the stove. Thermostat* air control to the desired setting. It is best to refuel little and often to maintain clean and efficient 4.10 Do not load fuel higher than the log guard. It is not burning. recommended to load larg
Streszczenie treści zawartej na stronie nr. 7
oPeRATING INSTRUCTI oNS 9.2 Fuel Quality (Solid Fuel) 7. ASH ReMoVAl (Multi-fuel stoves) Use only recommended solid fuels, which are approved for use with closed appliances. Symptoms of poor performance related to unsuitable fuels include: 7.1 The burning of any fuel will produce ash, which will have to be removed after a period of use. This time will depend • Difficulty getting a fire going and keeping it burning well on the fuel used. Before removing the ash from the stove it • Smoky
Streszczenie treści zawartej na stronie nr. 8
oPeRATING INSTRUCTIoNS Windy days - Smoking from the appliance. This could 10.2 Stove glass cracking: be caused by turbulent airflow around chimney terminal, Please ensure when replacing the glass in your stove that possibly caused by the position of other buildings or you do not over tighten the screws on the glass clips as this obstacles nearby. This problem is, also, sometimes will cause stress in the glass and with the intense heating associated with oversize chimneys, which may eve
Streszczenie treści zawartej na stronie nr. 9
TeCHNICAl SPeCIFICATIoN SHeRAToN SToVe Model Sheraton - 7016 / 7017 / 7027 Wood kW 8.0 Nominal Heat Output 8.0 Solid Fuel kW mm 1.25 All Fuels Flue Draught at Nominal Heat Output 0.05 inch Wg 5.4 Wood g/s Flue Gas Mass Flow Solid g/s 5.1 Fuel 337 Wood °C Flue Gas Temperature at Spigot/Socket Solid Fuel °C 335 mm 150 Flue Outlet Size (Top or Rear Option) inch 6 Weight kg 80 Wood Seasoned wood (less than 20% moisture content) Recommended Fuels Briquette smokeless fuel suitable for closed applian
Streszczenie treści zawartej na stronie nr. 10
SITe ReQUIReMeNTS Before installation of this product please read these When completing the installation and building works you should instructions fully. comply with your responsibilities under the Health and Safety at Work Acts, and any new regulations, which may be introduced It is very important to also understand the requirements of the UK during the lifetime of these instructions. Building Regulations (England and Wales – Document J / Scotland - Part F, Eire - Document J), along with
Streszczenie treści zawartej na stronie nr. 11
SITe ReQUIReMeNTS HeARTH dIMeNSIoNS The appliance must stand on a constructional hearth with the minimum dimensions as shown in the diagram below. Check that the building has a suitable loadbearing capacity for the hearth and stove. If in doubt consult a structural engineer for advice before proceeding. 1200mm minimum 150mm 150mm minimum minimum 150mm minimum Constructional Hearth Constructional Hearth 840mm minimum 840mm minimum PR7216S If you are fitting the appliance into an existing heart
Streszczenie treści zawartej na stronie nr. 12
SITe ReQUIReMeNTS WAllS NeXT To A HeARTH Thickness W Solid, non-combustible material e.g. masonary or concrete H C 150mm minimum 150mm minimum C PR7217S Dimensions of non-combustible material around Stove Location of Stove and Hearth Distance ‘C’ Thickness ‘W’ Height ‘H’ If the hearth touches the wall and the stove is placed Height of stove + 300mm or 0-50mm from the same wall the non-combustible Zero mm 200mm 1200mm above
Streszczenie treści zawartej na stronie nr. 13
PRe-INSTAllATIoN CHeCKS It is important that adequate ventilation exists and the flue or 1.13 Check the flue draught. This should be done with all chimney system that is to be used is in good working condition. windows and doors closed and any extraction fans in this Products of combustion that enter the room could be a serious or adjoining rooms running at maximum speed. (See next health risk. Before installation of this product we recommend section for additional ventilation requirements) t
Streszczenie treści zawartej na stronie nr. 14
PRe-INSTAllATIoN CHeCKS Model Sheraton - 7016 / 7017 / 7027 150 mm Without liner system round (diameter) 6 inch 135 mm Flue/Chimney Without liner system (square) Size minimum dimension 1 5 / inch 2 150 mm With liner or factory made system (diameter) installed in accordance with manufacturers instructions 6 inch 4.5 m Flue/Chimney minimum height* 15 feet * When measured from the top of the stove to the top of the flue, with no horizontal sections and a maximum of 4 bends with angles of less t
Streszczenie treści zawartej na stronie nr. 15
INSTAllATIoN INSTRUCTIoNS Because each installation is unique to the property, it is not 1.4 Lift the stove into position on the prepared hearth area, possible to give full details to suit every setting. However, the taking care not to damage the hearth finish. Level stove installation should comply with the requirements of the Building using foot adjusting bolts. Regulations and be made using "best practice" construction methods. 1.5 Connect the stove to the chimney system, using Stovax en
Streszczenie treści zawartej na stronie nr. 16
INSTAllATIoN INSTRUCTIoNS 1.9 Connect a straight piece of flue pipe by inserting it into the 4. FITTING & ReMoVAl oF THe BAFFle flue spigot and seal using fire cement and secure with a suitable self tapping screw. 4.1 To maintain safe and efficient combustion the stove is fitted with a baffle in the top of the firebox. To chimney connection as detailed in building regulations 4.2 Allow the stove to cool fully before removing baffle system. Elbow with access cover 4.3 Remove baffle suppo
Streszczenie treści zawartej na stronie nr. 17
CoMMISSIoNING 1.1 Replace the firebricks, baffle, and log retainer. 1.2 Check the door alignment and catch operation, adjust if required. 1.3 Inspect the door seals for damage and check the operation of the air controls. 1.4 Carry out a final smoke draw test, by first warming the flue with a blowlamp, or similar, for about 10 minutes. Then place a smoke pellet on the centre of the grate, with the air controls open, and close the door. Smoke should now be drawn up the flue and be seen to e
Streszczenie treści zawartej na stronie nr. 18
MAINTeNANCe and SeRVICING See chart on page 19 for common spare parts refered to in this section. For a complete list of spare parts and accessories contact your Stovax dealer for the Stovax Fireplace, Stove & Hearth Accessories brochure or call 01392 474011 on how to remove the baffles and firebricks. Care should be 1. GeNeRAl CleANING taken when handling firebricks, as they can become fragile after a period of use. Before any cleaning is carried out, allow stove to cool thoroughly to av
Streszczenie treści zawartej na stronie nr. 19
MAINTeNANCe and SeRVICING This is a list of the maintenance products you may need to use 5. ReMoVAl oF THe loG GUARd Stovax Code Task Product name Number 5.1 Remove the log guard by lifting clear of the supporting Stove glass cleaner 500ml brackets and rotating to clear the sides of the door opening. 4111 (wipe on) The stove should not be used without the log guard in Glass cleaning position. Stove glass cleaner 4103 (spray on) 6. FITTING & ReMoVAl oF FIReBRICKS Preventing build- Protec
Streszczenie treści zawartej na stronie nr. 20
MAINTeNANCe and SeRVICING Seal 14mm Fixing Screw (x10) Glass (x2) Seal 10mm x 2mm Glass Seal (3mm) Fixing Clip (x4) Door (x2) 9.3 Remove the old rope and scrape old glue from the locating 8.3 Using a screwdriver remove the glass clip fixing screws. The groove. Clean the locating groove with a clean dry cloth to old glass can then be lifted clear of the door. (Note how remove all old dust and debris. the 3mm sealing rope is placed between the glass and the door.) Remember to dispose of the old
