Streszczenie treści zawartej na stronie nr. 1
Irving Oil
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
Freestanding
BEFORE INSTALLING AND
Direct Vent
USING APPLIANCE
Fireplaces
WARNING!
IRFSDV24
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION
IRFSDV34
MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY
OR LOSS OF LIFE.
FOR YOUR SAFETY
Installation and service must
be performed by a qualified in-
staller, service agency or
the gas supplier.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to
Streszczenie treści zawartej na stronie nr. 2
Irving Oil TABLE OF CONTENTS PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a Irving Oil fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Installation Instructions ........................................................................................................
Streszczenie treści zawartej na stronie nr. 3
Irving Oil INSTALLATION & OPERATING INSTRUCTIONS This gas fireplace should be installed by a qualified installer in accordance with local building codes and with IMPORTANT: current CSA-B149 (.1 or .2) Installation codes for Gas PLEASE REVIEW THE FOLLOWING CAREFULLY Burning Appliances and Equipment. For USA Installations follow local codes and/or the current National Fuel Gas Remove any plastic from parts before turning the Code. ANSI Z223.1. If the unit is being installed in a fireplace ON. mobi
Streszczenie treści zawartej na stronie nr. 4
Irving Oil FIREPLACE DIMENSIONS IRFSDV24 IRFSDV34 A 23 in (584 mm) A 26-14 in (667 mm) B 28-3/4 in (730 mm) B 31-1/2 in (800 mm) C 16-5/8 in (422 mm) C 19-3/8 in (492 mm) D 27-3/8 in (695 mm) D 30 in (762 mm) E 9-1/2 in (241 mm) E 10 in (254 mm) F 13-7/8 in (352 mm) F 15-1/2 in (394 mm) G 4 in (102 mm) G 4-1/2 in (114 mm) H 23 in (584 mm) H 26-1/4” (667 mm) I 11-1/2 in (292 mm) I 13-1/8 “ (334 mm) J 16-5/8 in (422 mm) J 19-1/2” (495 mm) K 6” (152 mm) K 6-3/8 in (162 mm) 4 10004000
Streszczenie treści zawartej na stronie nr. 5
Irving Oil GAS SPECIFICATIONS PREPARATION The use of wall paper adjacent to this Max. Max. fireplace is not recommended, as the high heat given off by this fireplace may Input Input adversely affect the binders in the Model Fuel Gas Control BTU/h BTU/h adhesive used to apply the wallpaper. IRFSDV24RN Nat Millivolt Hi/Lo 20,000 14,000 Before beginning, remove the window frame assembly IRFSDV24RP Prop Millivolt Hi/Lo 20,000 15,000 from the fireplace. Also check to make sure there is not hidden d
Streszczenie treści zawartej na stronie nr. 6
L I P TPTH TP TH Irving Oil When using copper or flex connector use only ap- INSTALLATION OF REMOTE proved fittings. Always provide a union when using SWITCH FOR RN/RP GAS VALVE black iron pipe so that gas line can be easily disconnected for burner or fan servicing (see Fig. 2) The remote ON/OFF switch can not be fitted to units See gas specification for pressure details and ratings. using the Honeywell Radio Frequency control valve. The fireplace valve must not be If the fireplace has been fi
Streszczenie treści zawartej na stronie nr. 7
V V Operable Irving Oil GENERAL VENTING INFORMATION–TERMINATION LOCATION INSIDE CORNER DETAIL G V N H N A D E B C B Fixed Fixed L V B V Closed Closed V Fixed Operable G Closed F V V B M V G B J X B X I V K V A A VENT TERMINATION X AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED V CFM145a 1 2 Canadian Installations US Installations A = Clearance above grade, veranda, porch, 12 inches (30cm) 12 inches (30 cm) deck, or balcony B = Clearance to window/door that may be opened 6 in (15cm) for ap
Streszczenie treści zawartej na stronie nr. 8
Irving Oil Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. Inside Corner Recessed Location Outside Corner D B = C C Combustible A = 6"(152mm) Combustible E A 6"(152mm) Noncombustible V V 2"(50mm) Noncombustible 2"(50mm) V B Fig. 6 Fig. 7 Balcony - Balcony - with no side wall with perpendicular side wall C = Maximum depth of 48" (1219mm) for recessed H G location. V V D = Minimum width for back wall
Streszczenie treści zawartej na stronie nr. 9
Irving Oil GENERAL INFORMATION ON ASSEMBLING THE VENT PIPES IN DIRECT VENT APPLICATIONS NOTE: Only venting components manufactured by The Vermont Castings Majestic Products Company may be used. CRIMPED END PIPES TWIST LOCK PIPES Before joining elbows and pipes apply a bead of high When using twist-lock pipe it is not necessary to use temperature sealant to the crimped end of the elbow or sealant on the twist lock joints. pipe. Join the pipes using a 2” (50mm) overlap and The only areas of the ve
Streszczenie treści zawartej na stronie nr. 10
Irving Oil Example: In Figure 13 VERTICAL SIDEWALL INSTALLATIONS Elbow 1 = 90° Elbow 2 = 45° Elbow 3 = 45° Since it is very important that the venting system Elbow 4 = 90° maintain its balance between the combustion air intake and the flue gas exhaust, certain limitations as to vent Total angular variation = 270° configurations apply and must be strictly adhered to. The graph, on page 11, showing the relationship between vertical and horizontal side wall venting will help to determine the variou
Streszczenie treści zawartej na stronie nr. 11
Vertical Dimension From The Floor Of The Fireplace To The Center Of The Horizontal Vent Pipe Irving Oil TO USE THE VENT GRAPH 1. Determine the height of the center of the horizontal vent pipe exiting through the outer wall. Using this dimension on the Sidewall Vent Graph below, locate the point it intersects with the slanted graph line. 2. From the point of this intersection, draw a vertical line to the bottom of the graph. 3. Select the indicated dimension, and position the fireplace in accord
Streszczenie treści zawartej na stronie nr. 12
Irving Oil STEP 3 VENT PIPE ASSEMBLY Place fireplace into position (Fig. 19). Measure the vertical height (X) required from the base of the flue collars to the center of the wall opening. STEP 1 Locate vent opening on the wall. It may be necessary to first position the fireplace and measure to obtain hole location. Depending on whether the wall is combustible or noncombustible, cut opening to size (Fig. 17). (For combustible walls first frame in opening. Fig. 17) Vent Opening X Combustible Wal
Streszczenie treści zawartej na stronie nr. 13
Irving Oil STEP 5 STEP 7 Apply high temperature sealant to 4” (100 mm) and 7” Measure the horizontal length requirement including a (175 mm) collars or the termination one inch away from 2” (50 mm) overlap, i.e. from the elbow to the outside crimped end. Guide the vent terminations 4” and 7” wall face plus 2” (or the distance required if installing a collars into their respective vent pipes. Double check second 90° elbow (Fig. 21). that the vent pipes overlap the collars by 2” (50mm). Secure the
Streszczenie treści zawartej na stronie nr. 14
Irving Oil If installing a snorkel a minimum 24” vertical rise is necessary. The maximum horizontal run with the 24” vertical pipe is 36” (915 mm). This measurement is taken from the collar of the fireplace to the face of the FOUNDATION RECESS exterior wall. See the Vent Chart on page 11 for SNORKEL extended horizontal run if the vertical rise exceeds 24”. WATERTIGHT SEAL 1. Establish vent hole through the wall (Fig. 17). AROUND WALL PIPE 2. Remove soil to a depth of approximately 16" SCREWS
Streszczenie treści zawartej na stronie nr. 15
Irving Oil installations. From 0 to a maximum of 8’ of vent TO INSTALL VERTICAL VENTING pipe can be used between elbows (Fig. 25). • 7DVCS must be used to support offsets (Fig. 1. Locate your fireplace. 26). This application will require that you first 2. Plumb to center of the (4”) flue collar from ceiling determine the roof pitch and use the appropriate above and mark position. 3. Cut opening equal to 9-3/8” x 9-3/8” (240 mm x starter kit. (See Venting Components List) 240 mm). 4. Proceed to p
Streszczenie treści zawartej na stronie nr. 16
Irving Oil CRIMPED END VENTING COMPONENTS Starter Kit-Model 7FSDVSK-Sidewall Venting Starter Kit-Model 7TDVSKV-Vertical Venting for 7DVSKV-A order 1/12 to 6/12 roof pitch for 7DVSKV-B order 7/12 to 12/12 roof pitch for 7DVSKV-F order flat roof Starter Kit-Model 7FSDVSKS-Snorkel Kit for Below Grade Installation 45˚ elbow kit 7FSDVT45G for Vertical Installation Offsets 90˚ Transition elbow kit 7DVRT90 for Vertical Sidewall Applications or through-the-roof. Telescopic vent sections 7DVP610 -6” to 1
Streszczenie treści zawartej na stronie nr. 17
Irving Oil TWIST LOCK VENTING COMPONENTS Starter Kit - Model 7TFSMSK Starter Kit-Model 7TFSDVSK-Sidewall Venting Starter Kit-Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitch for 7TDVSKV-B order 7/12 to 12/12 roof pitch for 7TDVSK-F order flat roof Starter Kit-Model 7TFSDVSKS-Snorkel Kit for Below Grade Installation 45˚ elbow kit 7TFSDV45 for Vertical Installation Offsets 90˚ Transition elbow kit 7TFSDV90 for Vertical Sidewall Applications or through-the-roof. Telescop
Streszczenie treści zawartej na stronie nr. 18
Irving Oil OPERATING INSTRUCTIONS GENERAL GLASS INFORMATION INSTALLATION OF LOGS & BURNER LAVA ROCK MATERIAL Only glass approved by the Vermont Castings, Majestic Products Company may be used for replacement. Model: IRFSDV34 Refer Figure 32. • The use of substitute glass will void all pro- duct warranties. • Care must be taken to avoid breakage of the glass. 1. Remove window frame assembly (See “Window Under no circumstances should this Frame Assembly” section). fireplace be operated without th
Streszczenie treści zawartej na stronie nr. 19
Irving Oil MAINTENANCE INSTALLATION OF LOGS & BURNER LAVA ROCK MATERIAL (Cont.) 1. It is important to keep the burner and the burner compartment clean. This must be done Model: IRFSDV24 periodically, at least once per season (See Cleaning Procedure). Refer Figure 33. 2. Clean the brass trim using a soft clean cloth, 1. Remove window frame assembly (See Window Frame slightly dampened with lemon oil and buff with a soft clean cloth. Do NOT use brass polish or Assembly section). household cleaners
Streszczenie treści zawartej na stronie nr. 20
Irving Oil FLAME & TEMPERATURE ADJUSTMENT RN/RP Models For units equipped with ‘HI/LO’ valves the flame adjustment is accomplished by rotating the ‘HI/LO’ knob located near the center of the gas control valve (See Fig. below). IRFSDV24 Fig. 35 Turn Turn clockwise counterclockwise to increase to decrease flame height flame height Honeywell Valve FLAME CHARACTERISTICS It is important to periodically perform a visual check of the pilot and burner flames. Compare them to the pictorials illustrated
