Streszczenie treści zawartej na stronie nr. 1
Owners &
™
L676 Sunrise Gas Fireplace
Installation Manual
www.regency-fi re.com
MODELS: L676S-NG1 Natural Gas L676S-LP1 Propane
WARNING:
FOR YOUR SAFETY
If the information in these instructions are not followed exactly,
What to do if you smell gas:
a fi re or explosion may result causing property damage,
Do not try to light any appliance
personal injury or loss of life.
Do not touch any electrical switch:
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or use gaso
Streszczenie treści zawartej na stronie nr. 2
To the New Owner: Congratulations! ® You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The L676S has been designed to provide you with all the warmth and charm of a fi replace at the fl ick of a switch. The model L676S has been approved by Warnock Hersey for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with ® the
Streszczenie treści zawartej na stronie nr. 3
TABLE OF CONTENTS Gas Line Installation ....................................................28 SAFETY LABEL Pilot Adjustment ...........................................................28 Gas Pipe Pressure Testing ..........................................28 Copy of Safety Decal .....................................................4 SIT 820 Valve Description ...........................................28 Aeration Adjustment ....................................................29 REQUIREMENTS Wiring
Streszczenie treści zawartej na stronie nr. 4
Model/Modele: Model/Modele: L676S-LP1 L676S-NG1 SAFETY LABEL This is a copy of the label that accompanies each L676S-NG1 and L676S-LP1 Direct Vent 342 Gas Fireplace. We have printed a copy of the contents here for your review. DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ETIQUETTE ® NOTE: Regency units are constantly being improved. Check the label on the unit and if 342 there is a difference, the label on the unit is the correct one. Serial No. / No de serie Listed: VENTED GAS FIREPLA
Streszczenie treści zawartej na stronie nr. 5
INSTALLATION REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above
Streszczenie treści zawartej na stronie nr. 6
UNIT DIMENSIONS 6 6 Regency® L676S-1 Direct Vent Gas Fireplace INSTALLATION
Streszczenie treści zawartej na stronie nr. 7
INSTALLATION INSTALLATION 12) Installation and any repairs to this appliance YOUNG CHILDREN SHOULD BE IMPORTANT MESSAGE should be done by an authorized service CAREFULLY SUPERVISED WHEN person. A professional service person should SAVE THESE THEY ARE IN THE SAME ROOM AS be called to inspect this appliance annually. THE APPLIANCE. Make it a practice to have all of your gas INSTRUCTIONS appliances checked annually. The L676S Direct Vent Fireplace must be CLOTHING OR OTHER FLAMMABLE 1
Streszczenie treści zawartej na stronie nr. 8
INSTALLATION 9) Test Gas Pressure (Refer to "Gas Pipe Pres- 3) The L676S Direct Vent Gas Fireplace can HEAT RELEASE KIT sure Testing" section). be installed in a recessed position or framed out into the room as in A, B, C and D. See The Heat Release Kit expels warm air from the Diagram 1. 10) Install standard and optional features. Refer fi replace to the outside of the building, allowing to the following sections: the fi replace to be operated with less heat entering the room. The kit
Streszczenie treści zawartej na stronie nr. 9
INSTALLATION INSTALLATION CLEARANCES The clearances listed below are Minimum distances unless otherwise stated: A major cause of chimney related fi res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fi replace and vent system be installed only in accordance with these instructions. Caution Requirements The top, back and sides of the fi replace are defi ned by standoffs. The metal ends of the standoff may NOT be recessed
Streszczenie treści zawartej na stronie nr. 10
INSTALLATION MANTEL CLEARANCES Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram below. Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board. Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour. MANTEL LEG CLEARANCES Combustible ma
Streszczenie treści zawartej na stronie nr. 11
INSTALLATION INSTALLATION FRAMING 1) Frame in the enclosure for the unit with framing material. The framed Note: When constructing the framed opening, please ensure opening for the assembled kit is 45-7/8" high x 43" wide x 24-1/2" there is access to install the gas lines when the unit is deep (1143mm x H 1092mm W x 622mm D). See Diagram 1. Also installed. See Diagram 3 for details. see Diagram 2 for corner installations. IMPORTANT: Header must be metal stud. All other framing may
Streszczenie treści zawartej na stronie nr. 12
INSTALLATION FINISHING 1) Finishing material such as tile, river rock, etc. must not protrude beyond the front facing fl anges on all 4 sides of the fi rebox opening. NON-COMBUSTIBLE REQUIREMENTS Metal 44-1/2" 2) If material such as brick, stone, etc. extends past the faceplate depth, Stud (1130mm) when fi nishing around the faceplate, the minimum opening dimension noted below (Diagram 3) must be adhered to - to ensure the faceplate can be removed. Non-combustible 36 -1/4” Material 31-5/8"
Streszczenie treści zawartej na stronie nr. 13
INSTALLATION INSTALLATION To accommodate various thicknesses of facing material - the faceplate is adjustable to a maximum of 1-1/4" and a minimum of 1/2" . See chart below and page 35 for detailed instructions. Finished Facing Thickness Faceplate Adjustment 1/2" Factory Setting 1/2" - 7/8" (or less) Adjusted to + 3/8" 7/8" - 1-1/4" (or less) Adjusted to + 3/4" Diagram 5 Regency® L676S Direct Vent Gas Fireplace 13
Streszczenie treści zawartej na stronie nr. 14
INSTALLATION SIDE NAILING STRIPS The Finishing Template uses two magnets to UNIT ASSEMBLY attach itself to the fl ange on the left or right side of the unit (see diagram below). Install the The side nailing strips come attached to the unit. PRIOR TO facing material up to the outside edge (when There are 2 plates on each side, one on the top INSTALLATION facing the unit) of the fi nishing template. This and bottom that can be folded out as required. template may be discarded after the fac
Streszczenie treści zawartej na stronie nr. 15
INSTALLATION INSTALLATION VENT RESTRICTOR POSITION Latch Vent restriction is required for certain venting installations, see the diagrams in the "Venting Arrangements" section to determine if they are required for your installation. The Vent Restrictor plate is located on the inside top of the fi rebox. 2- ½” Vent Restrictor Plate Vent Restrictor Set 1 b. Swing the door out from the top and release the hinge on the left side of the door and lift out. Factory Set Vent Restrictor Set (no
Streszczenie treści zawartej na stronie nr. 16
INSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTS 1 2 Canada USA Minimum Clearance Requirements A Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm) B Clearance to window or door that may be opened 12"(30cm) 9" (23cm) C Clearance to permanently closed window ** D Vertical clearance to ventilated soffi t located above the terminal within a horizontal distance of 2 feet (61cm) 24"(60cm)) 24"(60cm)) E Clearance to unventilated soffi t 24"(60cm) 24"(60cm) F Clearance to outs
Streszczenie treści zawartej na stronie nr. 17
INSTALLATION INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATION (FLEX) ® Regency Direct Vent System These venting systems, in combination with the L676S, have been tested and listed as a direct vent system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram from the "Exterior Vent Termination Locations" section. FPI Direct Vent (Flex) System Termination Kits include all the parts needed to install the L676S usi
Streszczenie treści zawartej na stronie nr. 18
INSTALLATION RIGID PIPE VENTING SYSTEMS BASIC HORIZONTAL & VERTICAL TERMINATIONS Vertical Terminal Rigid Pipe Vent Systems offer a complete line of component parts for installation of both horizontal and vertical installations. Many Storm Collar items are offered in decorative black, as well as galvanized fi nish. Flashing The minimum components required for a basic horizontal termination are: Ceiling Firestop 1 AstroCap XL Vinyl Siding o 1 90 Elbow Standoff (Optional) Vent Guard - if re
Streszczenie treści zawartej na stronie nr. 19
INSTALLATION INSTALLATION 5” X 8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Regency® L676S Direct Vent Gas Fireplace 19
Streszczenie treści zawartej na stronie nr. 20
INSTALLATION 20 Regency® L676S Direct Vent Gas Fireplace INSTALLATION
