Instrukcja obsługi Monte Carlo Fan Company 5CLR66XXD Series

Streszczenie treści zawartej na stronie nr. 1

Owner’s
Manual
Ceiling Fan Installation Instructions
Total fan weigh
with light
For 5CLR66XXD Series Fans
READ AND SAVE THESE INSTRUCTIONS
Quality Ceiling fans

Streszczenie treści zawartej na stronie nr. 2

Installation SAFETY TIPS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS 1. Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70- 1999), including fire-rated construction. 2. Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer. 3. After making the wire connections,

Streszczenie treści zawartej na stronie nr. 3

7 8 9 Lift mounting neck to mounting Plate and align Secure mounting neck to the mounting plate Remove keeper from cross pin and with four screws to become a complete mount- screws. then cross pin from yoke. Replace ing bracket. keeper on cross pin and save. 10 11 12 Loosen lock nuts and screws on yoke Loosen set screw that holds ball. Slide ball down and remove pin save till you can not feel screw on inside pin for later. of yoke. 13 14 15 Install downrod into yoke. Align hole Tighten 2 downro

Streszczenie treści zawartej na stronie nr. 4

21 19 20 Place ball on downrod. Replace pin Install canopy onto downrod. Thread leadwires and safety cable removed earlier and pull ball up so that through ball. the pin fits in the notches in the ball. 22 23 24 Remote Transmitter Dip swtiches Remote Receiver Dip switches Set dip switches on the Remote Transmitter and Remote Receiver to the same settings. This must be done so the units will communcate properly. If you have other fans you Tighten set screw to hold ball in can set to control fro

Streszczenie treści zawartej na stronie nr. 5

31 32 33 Loosen 2 screws and remove 1 Twist lower cover plate into place by Align the blade and then the blade screw. Save screw removed. plate with castings on motor to twisting in direction of arrow. attach blades to motor. Replace 1 screw removed and tighten all 3 screws securely. 36 34 35 Place light kit over screws and twist direction of arrow into place. Then Loosen 3 screws on light plate as Plug white wire from fan to white tighten all 3 screws securely. shown. wire from light kit. T

Streszczenie treści zawartej na stronie nr. 6

43 Remote Control Transmitter Features: Attach front cover to wall control with screws provided. Snap battery cover in place. FAN REVERSE LED LIGHT (Press once to change direction of MEDIUM SPEED the fan)Fanmust be running to reverse. LOW SPEED HIGH SPEED FAN OFF SETTING LIGHT ON/OFF SET- (Turns fan off only) TING AND DIMMER (Press and hold to dim light infinitively) FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”. LIGHT DIMMER T

Streszczenie treści zawartej na stronie nr. 7

Trouble Shooting If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning: Before servicing or cleanin

Streszczenie treści zawartej na stronie nr. 8

6/21/06 REV.0 New made from 5GMR manual